Search Documents

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, Which in Many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over wide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals now being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the same for all of the tars studied. Also, it mast function equally well for both low and high temperature tar permit accurate fractionation, and reduce adventitious decomposition to a minimum. The authors are aware that certain types of distillation analysis which do not meet the above requirements may give results comparable with those of the large stills of a by-product coke-plant where one type of tar is produced. These may be simpler and shorter and entirely suitable for control work, but at the same time have little value in a fundamental investigation.

Jan 1, 1932

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By Thomas E. Popplewell

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing the mining and treatment methods and costs obtained in sand and gravel plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By T. E. Swigart

In connection with experimental work by the Bureau of Mines to determine effects of back pressure . on oil wells * , data were compiled on the engineering conditions in the oil field selected , in order to afford a more complete understanding of the wells tested , and to illustrate the extent to which underground conditions should be studied when making oil -field experiments of this nature . This report , containing the data mentioned, may be of interest to the oil industry , as it describes briefly the methods of operation employed in developing and exploiting shallow well territory .

Feb 1, 1923

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressures. New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 2010

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage arc also described. IntroductionThe association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate ·formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation.In its most general form, the process of agglomeration involves taking discrete, independent particles, bringing them into contact with one another, promoting (or allowing) interparticle adhesion to occur and then causing structure rearrangement, usually under the action of external forces. The relative importance of these steps varies with the nature of the particulate system being agglomerated and with the kinds of agglomerates being produced. Coagulation or flocculation of particles dispersed in fluids is generally dominated by the contact and adhesion steps. In the granulation of powders, on the other hand, particles are already in contact so that structure rearrangement is the principal step."

Mar 1, 1992

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

In spite of advances in measurement techniques and an explosive increase in the volume of research, our understanding of human strength remains in its introductory stages. It is clear that muscle strength is a highly complex and variable function that depends on a large number of factors. It is not surprising, therefore, that large differences in strength exist not only between individuals, but even within the same individual tested repeatedly on a given piece of equipment. The issue is compounded by the fact that correlations of strength among different muscle groups in the same individual are generally low, and tests of isometric strength do not necessarily reflect the strength an individual might exhibit in a dynamic test. As a result of these and other influences, great care needs to be exercised in designing, evaluating, reporting, and interpreting muscular strength assessments. Traditionally, tests of muscular strength were in the domain of the orthopaedist, physical therapist, and exercise physiologist. Such tests are also an important tool for the ergonomist, however, because of the high strength demands on workers in manual materials-handling tasks. In some cases, task demands may approach or even exceed the strength that an individual is voluntarily willing to exert in a test of strength. In such cases, evidence suggests that the likelihood of injury is significantly greater than when the task demands lie well within an individual's strength capacity. Because the relationship among strength capabilities, job demands, and musculoskeletal injury has been established, it is apparent that tests of muscular strength may benefit the ergonomist both in designing jobs and in ensuring that individuals have sufficient strength to safely perform physically demanding jobs. Several strength assessment techniques have been employed for these purposes, each possessing unique characteristics and applicability to job design and worker selection procedures. Our main purpose has been to elucidate these strengths and weaknesses, so that tests of strength may be properly applied in designing jobs and selecting workers. One of the crucial points we have emphasized is that any test of strength used in job design or worker selection must be directly related to the demands of the job.(1) For example, if an occupational lifting task has a high dynamic component, a test of isometric strength is not likely to provide the data necessary for proper design of the job. Of course, dynamic strength tests would also be misapplied in assessing a job requiring isometric exertions. Another potential pitfall is using tests of strength on isolated muscle groups and assuming that they are indicative of whole-body strength. For example, one might mistakenly assume that dynamic trunk extension strength represents a person's capability to perform a lifting task. However, an individual's lifting capacity may be entirely unrelated to trunk extension strength. It may, instead, be limited by an individual's arm or leg strength, depending on the task being performed. A final point on strength assessment should be made. An individual's strength capability cannot be considered a fixed human attribute. Strength training regimens can increase an individual's strength capability by 30%-40%. Whether

Jan 1, 1998

By R. Barany

The heats of the glass-crystal transformation of nepheline (Na0.7794K0.2206AlSiO4) and wollastonite (CaSiO3) and the heat of formation of nepheline at 298.15° K were determined by solution calorimetry. For the glass-crystal transformations, the heat values were -9.0 ± 0.3 kcal/mole for nepheline and -8.1 ± 0.2 kcal/mole for wollastonite. The heat of formation of nepheline was -34.8 ± 0.6 kcal/mole from the oxides and -501.0 ± 0.5 kcal/mole from the elements.

Jan 1, 1966

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993