Search Documents

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are established it can be ascertained with a,of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town, whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well under drained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive."

Jun 1, 1921

By Louis A. Panek

The practice of roof bolting, now recognized as an effective method of support, is based largely on rule of thumb. Among the various applications of bolting, the support of stratified mine roof is by far the most common. The general principles relating to this type of reinforcement are presented in two companion reports; the first describes the function of the bolts, the bolting pattern, and the behavior of bolted roof (1), 2/ and the second describes the design of the models and the theory of the experimental method (2). This report presents a rational method for designing systems of vertical bolts to reinforce horizontally bedded mine roof, developed from model tests. The structure treated herein may be described as follows: The immediate roof, consisting of beds of like material and equal thickness with no bond between them, is reinforced by vertical bolts installed in straight lines across the opening; the case of suspension is excluded because the bolts are assumed not to extend above the immediate roof. The assumption is made that the behavior of the lowest bed approximates that of a rectangular plate clamped along two opposite sides (the ribs). These specifications represent approximately the roof conditions encountered in mining bedded deposits of all kinds - coal, potash, iron ore, etc. Thus, for the design of a roof-bolting system a quantitative solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, how does the support depend upon the length, spacing, and tightness of the bolts?

Jan 1, 1956

By B. Olson, V. A. Marple, D. J. Radet

"Gravitational forces have been found to be an important factor in defining the particle collection efficiency curve of inertial impactors for large particles. In general it was found that if the parameter G = gW /V 0 2 (g is the gravitational acceleration. w is the nozzle diameter and V 0 is the average fluid velocity at the nozzle throat) in greater than 10-3 the efficiency curve would shift to lower panicle sizes. No effect could be seen for lower values of G.IN'IRODUCTIONInertial impactors have long been used as classifiers for airborne particles. By proper design of the nozzles and flow rate it is possible to classify particles with a fairly sharp cut in the particle size range from approximately .02 µm to 50 µm. Because of inertial impactors wide usage they have been extensively studied calibrated and evaluated. Most of these studies have been experimental calibrations of single stages using monodisperse aerosol particles. However, due to impactor simplicity. i.e. a jet of particle laden air impinging upon a flat plate with large inertia particles crossing the streamlines and impacting upon the plate the impactor also lends itself to theoretical evaluation.The most comprehensive method for analyzing impactors theoretically is to use finite difference solutions to the Navier-Stokcs equations and solve for the velocity components and pressure at node points of a grid placed over the area of interest. Using iteration and relaxation techniques the value of the velocity vectors can be determined at these node points with good accuracy. Once the velocities arc known, theoretical particles of known size can be placed into the now field and their trajectories determined by analyzing their equation of motion using numerical methods.Rader and Marple (1985) have performed theoretical analysis on impactors and have included such factors as Ultra-Stoksian .drag and the physical diameter of the particle in their analysis. However, even with these· factors included, there appears to be discrepancy · between the experimental and theoretical results when the particle size is larger than approximately 4 or 5 µm. One possible reason for this discrepancy could be the effect of gravity on the particle as it passes through the impactor. Therefore, a program was initiated to study the effects of gravitational forces on the collection· efficiency of particles in impactors. The results of that study arc presented here."

Jan 1, 1990

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By Susan M. Moore

The objective of this study was to evaluate the circumstances leading to fall from equipment injuries in the mining industry. Method: The 2006 and 2007 Mine Safety and Health Administration annual injury databases were utilized for this study whereby the injury narrative, nature of injury, body part injured, mine type, age at injury, and days lost were evaluated for each injury. Results: The majority of injuries occurred at surface mining facilities (~60%) with fractures and sprains/strains being the most common injuries occurring to the major joints of the body. Nearly 50% of injuries occurred during ingress/egress, predominately during egress, and approximately 25% of injuries occurred during maintenance tasks. The majority of injuries occurred in relation to large trucks, wheel loaders, dozers, and conveyors/belts. The severity of injury was independent of age and the median days lost was seven days; however, there was a large range in severity. Impact on industry: From the data obtained in this study, several different research areas have been identified for future work, which include balance and stability control when descending ladders and equipment design for maintenance tasks.

Jan 1, 2009

By W. R. Moorehead

This paper, describing the mining methods and colt at the New Indria quicksilver mine, is one of a series of similar papers being prepared by the Bureau of Mines on various mines in the United States. The New Idria mine lies at an elevation of 3,500 to 4,200 feet in the Coast Range of San Benito County, Calif. The property is accessible by automobile stages from Gilroy or Hollister via Tres Pinos. Tres Pinos, 65 miles northwest of the mine, is the nearest railroad point.

Jan 1, 1931

By Hiram C. Draper

The Mining Division of the Bureau of Mines, in cooperation with the Obstacle and Demolition Branch, Engineer Research and Development Laboratories, Department of the Army, undertook some extensive tests to determine the effectiveness and limitations of using standard demolition-type shaped charges in underground Mining. The tests proved the shaped charge has no practical application in the functions of mining covered by this report. At an approximate cost of 0 per foot hole plus spall produced by the most efficient single shots with the M3 shaped charge, the cost is over 20 times that of producing a better hole with a rock drill. The concussion would prohibit its use in many mines, and the excess carbon monoxide gas liberated by the pontolite explosive would be an additional hazard when used underground.

Jan 1, 1948

By B. J. Scheiner

As part of the goal to maximize minerals and metals recovery from primary domestic resources, design factors associated with minimizing current leakage in bipolar cell configurations were studied by the Bureau of Mines as a means of improving the efficiency of bipolar e1ectrooxidation cells. Initial studies that were conducted in a small bipolar cell operating at 140 to 145 volts and 15.4 amp indicated how design factors could be employed to minimize cur-rent leakage around adjacent electrodes during cell operation. Based on these results, a 40-electrode, 108-kva prototype of an industrial-sized cell was constructed and tested for extracting metal values from offgrade molybdenite concentrates. The feasibility of recovering molybdenum and rhenium from the oxidized pulp also was determined. Feed to the process sequence consisted of flotation concentrates containing 16 to 35 pet Mo as molybdenite and 6 to 15 pct Cu. E1ectrooxidation in the prototype cell resulted in 84 to 97 pct Mo and Re extraction with a corresponding energy consumption of 9 to 13 kwhr/1b Mo extracted.

Jan 1, 1979

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to January 1, 1925, was published in Bureau of Mines Technical Paper 3761. The present list includes all equipment tested and approved by the Bureau, up to and including January 1, 1926, and supersedes the list issued as Serial 27202 in November, 1925. It covers electric air compressors, coal drills, mining machines, mine pumps, room hoists, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamp, methane indicators and detectors, blasting units, storage battery loco- motives, power trucks, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manu- facturer, after his equipment has passed certain tests prescribed by the bureau, to mark his equipment with a seal showing that it has been "approv- ed" by the Bureau of Mines. The tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Feb 1, 1926

By S. E. Khalafalla

The Bureau of Mines investigated variations in the activation energy for the carbon monoxide reduction of magnetite and ferrous oxide with respect to the state of aggregation of the oxide material. Reduction phenomena can only be satisfactorily explained by including an adsorption step in the reduction process. Summation of the values of the exothermic heat of chemisorption and the variable apparent activation energy for reduction yields a nearly constant value of about 50 kcal for either ferrous oxide or magnetite regardless of whether they are aggregated in pelletized form or coarsely crystalline particles.

Jan 1, 1965

By J. G. Eisele

Solvent-extraction characteristics of dodecyl phosphoric acid (DDPA) were investigated to determine its potential as a fractional or selective extract-ant for individual elements in a rare-earth-yttrium mixture. The DDPA is an effective extractant for splitting rare-earth mixtures into light and heavy subgroups. Yttrium normally extracts with the heavy rare-earth elements but may be shifted toward an extraction sequence with the light rare-earth elements by increasing the pH. Elements in the light and heavy ends of the rare-earth series can be separated from middle-group rare-earth elements by using diethylenetriaminepentaacetic acid (DTPA) as an aqueous phase counter-extractant. Hydrogen-ion dependency of the distribution coefficients differs from that reported for similar systems at tracer-level concentration.

Jan 1, 1965

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By Hal J. Kelly

A picture of the ceramic industrial potential of the Pacific Northwest States is presented by reviewing the present ceramic industries, raw-material resources, and current market demands. A resume is given of the industrial plants manufacturing ceramic ware as well as available information on raw-material resources. No attempt was made to prospect for new deposits but rather to evaluate, insofar as possible, those already known. Since much of the industry is concentrated on the Pacific coast, most of the information available on resources concerns deposits in that area. Large, undeveloped districts in Montana and Idaho, however, offer promise of larger reserves of ceramic raw materials. Average annual production, some operating costs, and annual power consumption are given for each of the plants. Production and some cost figures are listed to show the limited nature of the present industry and to suggest fields open for new development.

Jan 1, 1956

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965