Search Documents

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By Louis A. Panek

This report deals with the combined friction and suspension effects in the reinforcement of horizontally bedded mine roof by bolting. Other reports have treated these two effects separately. Friction effect refers to the reduction of bending in a laminated roof due to the clamping action of tensioned bolts. If the beds tend to have unequal deflections, the bolts oppose this tendency, thus creating a suspension effect, which consists of a transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds within the bolted unit. The combined effects of friction and suspension on the bending of the beds, whether an increase or a decrease, are difficult to generalize because they depend on the bedding sequence and the bolt pre-tension. Some analysis of the bedding sequence usually is required to determine the critical bed within a set of bolted beds. However, if the suspension effect is substantial and if the bolts are pre-tensioned, then the greatest bending stress is likely to occur in the thickest bed. Findings are based partly on theory and partly on tests of mine-roof models in a centrifuge, which were found to verify the theory. Mathematical formulas are obtained for the change in maximum roof bending stress and for the change of roof deflection due to the combined friction and suspension effects. The maximum bending stress is needed for designing a roof-bolting system and the deflection for evaluating its effectiveness.

Jan 1, 1962

By M. M. Fine

This report describes a Bureau of Mines technical feasibility study of simultaneous reduction and induration of pelletized iron ore to make a product with superior qualities as blast-furnace feed. Highly reduced, physically competent pellets can be made from magnetite and specularite concentrates that contain small additions of bentonite as binder. In batch tests, pellets were dried, surrounded with solid fuel in crucibles, and heated to the reducing temperature. Total iron content of the best products was higher than 80 percent and crushing strength of 1/2-inch metallized pellets ranged up to 600 pounds or more. Comparative tests of several commercial oxide pellets showed a wide range in crushing strengths, but most values were less than 350 pounds. Continuous tests in a rotary kiln resulted in the same degree of reduction, but the pellets had lower crushing strengths because of the limitations in the maximum operating temperature of the small kiln.

Jan 1, 1962

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By E. J. Ostrowski

The Bureau of Mines experimental blast furnace, Bruceton, Pa., was operated to determine the feasibility of replacing part of the burden coke requirements with solid fuels injected directly into the smelting zone. This report describes preliminary experiments and information resulting from such an interchange. These experiments were made on an all-sinter burden, using two parts sinter to one part fuel. Anthracite fines were injected intermittently into the smelting zone of the furnace by compressed air through auxiliary tuyeres. The interval between injection periods ranged from 5 to 15 minutes. A maximum of 28 percent of the stock column coke bur-den was replaced. This percentage replacement caused furnace malfunction, but the overall percentage of these experiments indicated that 20 to 24 percent of the coke requirements could be replaced in this way. The metallurgical coke consumption was decreased by as much as 377 pounds (25.3 percent) per ton of pig metal produced. Buckwheat anthracite No.4 was used in this experiment; however, such solids as bituminous coal or coke fines also could be used. The frequency as well as the quantity of solid fuel injected has a direct bearing on furnace performance.

Jan 1, 1960

By Michael D. Fenton

Bauxite resources were primarily in Africa, Asia, Oceania, and South America. Only five countries combined, Australia, Brazil, Guinea, India, and Jamaica, contained most of the total world reserves available for extraction under current economic conditions and accounted for nearly 80 % of world production of bauxite. World bauxite and alumina production declined and prices for smelter-grade alumina remained below the $200/mt level during 1993 because of growing aluminum inventories on international markets and declining worldwide demand. The United States imported bauxite primarily from Australia, Brazil, Guinea, and Jamaica. U.S. alumina plant capacity remained essentially unchanged throughout 1993, but apparent capacity utilization decreased by the close of 1993. Chromium Most of the world's known resources and reserves of chromite are located in India, Kazakhstan, South Africa, and Zimbabwe. India, Kazakhstan, and South Africa accounted for 73 % of world production of chromite. The two largest producers of chromite, Kazakhstan and South Africa, were in the process of major economic and political change during 1993. South Africa's production and exports of chromite continued to fall during 1993, because of weak international demand and a flood of cheap metal from the former U.S.S.R. and China into world markets. Despite a significant increase in production, South Africa's ferrochrome producers continued to operate below capacity in 1993. Prior o the dissolution of the U.S.S.R., Kazakhstan was a major internal supplier of chromite ore to the U.S.S.R. consumer, but subsequent decline in demand led to a downward trend of chromite production in Kazakhstan and increasing exports to Europe during 1992 and 1993. The United States consumed, about 10% of world chromite ore production in various forms of imported materials. The United States imported nearly one-half of its required chromium contained in chromite ore and chromium ferroalloys and metal from South Africa; the remainder was from the minor producers Turkey, Yugoslavia, Zimbabwe, and others.

Jan 1, 1995

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping ' compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

By E. Chin

Natural gas was the only economically significant mineral produced. A significant amount of the gas output was consumed in the production of nitrogen fertilizer and electric power. Proved reserves of natural gas were abundant and at least sufficient to supply most of the country's industrial and domestic needs for many decades to come. Other mineral production was of little importance to the Bangladesh economy, although there were prospects for developing some of the nonmetallic minerals. The flat river-delta terrain comprising nearly all of Bangladesh made the potential for discovering major, economically exploitable mineral deposits poor. The deep sediments, however, have good potential for crude oil or additional natural gas discoveries.

Jan 1, 1985

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By R. F. Abernethy

A small-scale method was developed for determining the free-swelling index of coal samples of limited quantity, especially the macerals. Results of a series of tests using a 0.3-gram sample correlated well with those by the standard method using a 1-gram sample. The standard and small-scale methods are modified to give unrestricted swelling for those coals having swelling index numbers above 7.

Jan 1, 1971

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By Sathit Tandanand

Massive roof overlying the working seam in longwall operations can cause hazards if it does not cave readily behind the face supports. The overhang thus formed can overload the supports and endanger personnel when it collapses suddenly as a large rock mass. This Bureau of Mines report proposes the use of a concentrated load, either strip or point loading, applied onto the roof with the help of the upward thrust of the face supports. An experiment was conducted in the laboratory to obtain information about break characteristics and the values of significant parameters of three sedimentary rocks. The results were used to determine the breaking load requirement for a strong roof possibly encountered in typical longwall operations. The results show that the roof slab of moderate thickness can be fractured within the load capacity of off-the-shelf powered supports.

Jan 1, 1979

By Douglas Pollock, John Organiscak

Water spray characteristics, including droplet size and velocity, airborne dust capture potential, and induced airflow quantity for various spray nozzle designs were evaluated to provide basic information for improving spray applications. Water droplet size and velocity characteristics were initially measured by a Phase Doppler Particle Analyzer (PDPA) for hollow cone, full cone, flat fan, and air atomized spray nozzles at similar operating parameters. Airflow inducement and dust capture experiments were also conducted under the same operating parameters to examine any salient features of the spray nozzle type, droplet characteristics, induced airflow, and airborne dust capture. Test results indicate that there are trade offs between airflow inducement and dust capture efficiency. A spray nozzle with a wider discharge angle was observed to induce more airflow, but at reduced dust capture efficiencies. Increasing spray nozzle fluid pressure(s) generally reduced water droplet sizes with concurrent increases in droplet velocity, airflow inducement, and airborne dust capture. Placing a three-sided barrier around the spray nozzles normally reduced spray air induction and increased dust capture efficiency. A direct relationship between airborne dust capture efficiency and spray input power normalized per unit of airflow induced was ob- served. This information can be utilized to improve the performance of water sprays for reducing airborne dust levels.