Search Documents

By Edward L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

By H. P. Greenwald, G. E. McElrey

"Part IV.- The Resistance Caused by Right-Angle Bends. IntroductionThis paper deals with the fourth phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the major results public as rapidly as possible. Parts I, II and III were issued as Serials Nos. 2621 (July 1924), 2647 (October 1904) and 2671 (March 1925) and dealt with the resistance of unobstructed entries, the resistance due to mine cars and, the resistance of timbered entries respectively.Description of the Tests With the last cutthrough between the two butt entries of the test section in the Experimental Mine open, the air flow was deflected, around two right-angle bends in the same direction, the butt entries being 50 feet center to center and approximately 6 by 9 feet in cross section. Each bend had a dead end opening off of it; that at the first bend was in the direction of flow and that at the second bond was at right angles to the flow. For a primary test condition the inner corner of each bend was trimmed square and the dead ends were closed off with board brattices set flush with the line of the cut-through.The two corners of the first band were, then modified both independently and in conjunction. Various modifications of both bends in conjunction were also tested with rather surprising results as to the effect of conditions at the first bend, upon the pressure losses at the second. To confirm the theory developed to fit these results a series of tests were made to give a direct comparison of the -pressure losses as between two bends with the air flow deflected in the some direction at each and with the air flow deflected in opposite directions. The former is designated ""double"" and the latter a ""reversed"" right-angle bend. This series of tests was conducted, however, on the bends at one of the intermediate cutthroughs at which the flow could be deflected us either direction at the second, bend. Here also the average cross-section was 6 by 9 feet and the bends were 50 feet apart."

Jan 1, 1928

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By H. M. Lawrence

"In the land-pebble district of Florida a lively interest in the possibilities of obtaining increased recoveries of phosphate rock is evident. Research in several directions is being carried on by companies operating in the district to increase the yields obtained by the washing plants. The Bureau of Mines is cooperating with this research program to promote more efficient plant practice and to avoid unnecessary depletion of mineral resources.Washing practice, as carried on in the district at present for the recover of phosphate rock from the crude ores or matrix, is not a complicated process. Flow sheets of the several companies are similar, although the equipment varies with the preferences of the individual operators. For disintegrating the matrix log washers are favored, although revolving drums equipped with flights to break up lumps of clay are also used. Fine sand is removed by screening. Vibrating screens have become well established in the district, although stationary flat screens and trammels are also employed.The writer acknowledges with appreciation the cooperation of the phosphate companies in the land-pebble district; suggestions and criticism by Will. H. Coghill, supervising engineer, Ore Dressing Section of the Bureau of Mines; and the laboratory assistance of J. O. Davie, J. W. Pamplin, and E. Roca, cooperative fellows of the University of Alabama.Losses in the Finer SizesOf the phosphate that is not recovered by present washing methods the greater portion is in the finer sizes. In these sizes the phosphate grains are accompanied by grains of sand - largely quartz - of the same size, and recovery of these phosphate grains as a commercial product is not possible by simple washing methods. Phosphate recoveries approaching complete extraction can only be effecte by applying metallurgical processes, either mechanical or chemical. As yet, most of these processes have not advanced much beyond the laboratory or perhaps the pilot-plant stage. Such processes may have some application to the beneficiation of phosphatic ores or washer rejects, but a discussion of them is not within the scope of this paper."

Apr 1, 1929

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By B. W. Madsen

As part of a program to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, the Bureau of Mines conducted research to determine the diffusion coefficients for ferric ions in synthetic copper leach solutions. Determination of ferric ion diffusion coefficients in typical dump leach solutions is necessary for predicting leaching rates of copper from large-scale leaching operations and for optimizing concentrations of ferric iron in solutions to maximize leaching efficiency. Derivative chronopotentiometry, an electroanalytical technique, was used to determine ferric ion diffusion coefficients. The diffusion coefficient decreased dramatically with increasing concentration of iron in solution. An empirical model was used to relate the ferric ion diffusion coefficient to the total amount of sulfate in solution. Measuring the diffusion coefficient dependence on temperature yielded an activation energy of 5.5 kcal/mole of ferric ion. Activity coefficients of ferric ions as a function of concentration were calculated from diffusion coefficient data.

Jan 1, 1981

Prevent the explosion of methane gas or coal dust by replacing air with inert gas inside highwall mine excavations. Approach Use combustion gases as a source of inert gas with low oxygen content to blanket the cutting, head of highwall mining machines. This gas is placed strategically at the collar of the excavation where it enters the hole to replace the mined coal volume. The elimination of oxygen from the hole prevents explosions of gas or dust. How It Works Highwall mining methods arc used when surface mining becomes uneconomical. One method of highwall mining involves use of a horizontal auger to enter the coalbed from a surface mine bench. The coal is mined in a series of horizontal, parallel, and large-diameter holes. Historically, little methane has been associated with auger mining. However, mining technology has extended the reach of auger mining, which can increase the occurrence of methane. Methane explosions at auger mining operations have been increasing. Methane has been the primary fuel source of these ignitions, but coal dust also may have been involved.

Jan 1, 1993

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

By David L. Moffatt

Considerable current interest is evident[l,2] in the use of transient electromagnetic methods for subsurface remote sensing. A transient method is discussed which uses a periodic video-type pulse containing a wide frequency range. A video pulse is used as an interrogating signal both for "target" identification and detection for relatively short depth (c 20 meters) applications in soil and soft rock media. If the medium is favorable, e.g., hard rock, greater depth applications appear to be feasible. The same procedures would be applicable for deep geological exploration but would require a substantial reduction in frequency and increase in target size. It should be noted that video pulse generators with 35 kv peak voltage and nanoseconds base widths are now within the state-of-the-art, thus significant power over broad spectral ranges is possible. In the design of a video pulse sounding system, 5 main problem areas can be identified; 1 ) selection of the pulse shape or spectral content of the video pulse, 2) design of a radiating structure which effectively couples such a pulse into the medium, 3) isolation of the radiating and receiving mechanisms, 4) realistically accounting for the dispersion and attentuation of the medium and the air-medium interface, and 5) interpretation or processing of the received signal waveform. Each of these problem areas will be discussed and illustrated with experimental and/or theoretical results. The Video Pulse Selection of the proper video pulse signal is dictated by 3 considerations, the maximum desired depth of penetration, the attenuation of the medium and the required resolution and size of the target. For a lossy medium, penetration and resolution are clearly at cross purposes and a compromise is necessary. The exact nature of the compromise is dictated by the application, but the spectrum of the video pulse should not contain any frequencies higher than the predicted cut-off, i.e., that frequency which is attenuated to the threshold level of the receiver. As a practical matter, it may be necessary to select 1 or 2 video pulses reasonably suited

Jan 1, 1973

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By W. J. Fene

"The prevalence of accidents in the coal-mining industry has prompted a study of the workmen's compensation laws of the various States and the statistics of accident costs, for the purpose of explaining to operators how the compensation laws are regulated and to show the cost of accidents.The subject of compensation laws and accident costs is by no means new, but the prevalence of coal-mine accidents would indicate that the mine operator in general is not thoroughly conversant with their importance. Unquestionably, compensation laws are a large factor in promoting accident prevention, and it is believed that a greater measure of success would be accomplished in preventing accidents if all mine operators were fully aware of their important bearing on the cost of production.Many operators seem to be indifferent to accident occurrence; possibly they do not real¬ize the seriousness of the accident hazards that exist in their mines, even after the hazards are brought to their attention. There is no question that material financial advantages are to be gained by the prevention of accidents and it would appear that when these advantages are thoroughly understood, operators would be anxious to eliminate, insofar as is feasible, conditions likely to cause accidents.The unsettled state of the mineral industry and the irregular operation of mines during the past several years has probably been an important factor in influencing the apparently indifferent attitude of the operator. The chaotic conditions in the mining industry and especially in coal mining are unquestionably a factor that tends to increase accidents, just as mine idleness increases roof hazards and results in deterioration in mechanical, electrical, and haulage equipment, and promotes disorganization of the personnel. During such times greater efforts should be exerted toward the prevention of accidents because of these increased hazards and of the financial advantages brought about by the various savings to be effected when mine accidents are held to a minimum.This report on accidents in the coal mines of Pennsylvania was made possible largely through the cooperation of William J. Maguire, director, Bureau of Statistics, Pennsylvania Department of Labor and Industry, and Rush N. Hosier, superintendent, Coal Mine Section, Pennsylvania Compensation Rating and Inspection Bureau, who made available their records and extended much assistance and numerous courtesies during this study."

May 1, 1932

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By S. E. Khalafalla

The ability of potentiometric, gas-sensing electrodes to reliably monitor free gaseous molecules in solution has been recently demonstrated. A gas such as sulfur dioxide from a dilute sample solution diffuses through a hydrophobic, gas-permeable membrane to an internal filling solution. The latter solution contains a sufficiently large excess of sodium bisulfite, the concentration of which can be considered constant regardless of the quantity of sulfur dioxide entering by diffusion. The electrode response is essentially due to the liberated hydrogen ions from the bisulfite-sulfur dioxide equilibrium. This Bureau of Mines report describes a new technique used to detect the formation, and to estimate the stability constant, of gas-molecule and gas-ion complexes in solution, as part of an effort to minimize the undesirable environmental impacts associated with mining and mineral processing. Although the unknown activity coefficients of the neutral and ionic species in the external solution complicate the quantitation of results, methods to circumvent these difficulties are presented. The technique is based on the isometric shift of the Nernst diagram of ion-selective electrodes to higher concentrations relative to the standard aqueous calibration curve. The method is applied to detect and estimate the formation constant of a sulfitocitrate complex, and agrees well with an independently determined stability constant of the disulfitomercu-rate complex.

Jan 1, 1978