Search Documents

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government's revenue.

Jan 1, 1986

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By Dean H. Ambrose

This paper presents an approach for representing and analyzing random motions and hazardous events in a simulated three-dimensional workplace, providing designers and analysts with a new technique for evaluating operator-machine interaction hazards in virtual environments. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. The project's methodology includes human factors design considerations, ergonomic modeling and simulation tools, laboratory validation, and collaboration with a mining equipment manufacturer. Hazardous conditions can be analyzed in virtual environments using collision detection. By simulating an operator's random behavior and machine's appendage velocity, researchers can accurately identify hazards, and use that information to form safe design parameters for mining equipment. Analysts must be discerning with the model and not read more from the databases than what the simulation model was designed to deliver. Simulations provided an interesting approach to data gathering in that there was no need for live subjects and logistics - test sites and costs associated with experiments-became insignificant. Collisions versus speed, operators' size, and risk behaviors proved the versatility found in the data obtained from the model. Preliminary results show that response time significantly affects the number of collisions experienced by the virtual subject. Also simulation data suggests that more mishaps occur with hand-on-boom-arm risk behavior.

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

By J. Roger Loebenstein

Demand for arsenic exceeded supply in 1980, and the major domestic and foreign producers allocated available supplies to customers. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-In June 1980, the Environmental Protection Agency (EPA) listed inorganic arsenic as a hazardous air pollutant.2 Proposed regulations on arsenic emissions were to be announced on an industry-by-industry basis at a future date, and public comment on the listing and on specific regulations was to be heard.

Jan 1, 1981

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for surface sand and gravel mines by state during 1990-2001. Table 28 also shows the injury risk rates, employees' working hours, and lost workdays. At surface sand and gravel mines, a total of 70 fires with 60 injuries occurred in 29 states during 1990-2001. Fifty-nine of the fires caused 60 injuries (none of the fires involved contractors). The yearly average was 5.8 fires and five injuries. The Ewhr value was 741 x 106 hr (Irr = 0.016), and the LWD value was 6,921. California had the most fires (nine fires and five injuries), followed by Michigan (six fires and six injuries) and Pennsylvania (five fires and five injuries). Of these states, Pennsylvania had the highest injury risk rate value (Irr = 0.052). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during the fourth period followed by a small increase during the fifth period and a sharp decrease during the last period. Employees' working hours increased during most of the periods. The Irr values follow patterns similar to those shown by the injury values.

Jan 1, 2004

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By Manuel Gomez

Prediction models were constructed for seam elevation, overburden, and sodium concentration for a lignite deposit in Ward County; N. Dak. These models were developed by mathematical-statistical techniques using surface coordinates as independent variables to permit interpolation between drill holes. The results suggest that sodium concentration in lignite may be predicted in advance of mining. This information is helpful to mine planning, specifically, in scheduling production to deliver a uniform product to existing powerplants.

Jan 1, 1970

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By Howard E. Parkinson

An environment monitoring and communication system has been installed in the Bruceton Mine, and research is under way to improve mine safety. Standard day-to-day mine communications are available, along with additional systems installed to permit experimentation with wireless radio, through-the-earth phones, along-the-roof paging, and mine face machinery communications. Research is continuing and the essential concepts for a dependable whole mine communication system, providing simple environment monitoring, improved day-to-day communications and post-disaster communications, will be demonstrated in a larger mine with about 900 feet of overburden.

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground metal/nonmetal and stone mines by state during 1990-2001. Table 10 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 12 fires occurred in 11 states; 5 of the fires caused 5 injuries. The yearly average was one fire and 0.42 injury. Five fires with two injuries occurred at metal mines, five fires with two injuries occurred at nonmetal mines, and two fires with one injury occurred at stone mines. None of the fires involved contractors. The Ewhr value was 58 x 106 hr (Irr = 0.017), and the LWD value was 75. Nevada had the most fires (two fires and no injuries). Ohio, New Mexico, Missouri, South Dakota, and Idaho each had one fire with one injury. Of these states, Missouri had the highest injury risk rate value (In = 0.25). Table 11, partly illustrated in figure 5, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the six time periods. The number of fire injuries and employees' working hours decreased during all of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 12-17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables related to fires for 1990-2001. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004