Search Documents

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By Donald R. Alvic

For electric utilities serving the aluminum smelter industry in the United States, sulfur oxide (SOx) abatement legislation could bring about increases in the costs of generating electricity. This paper documents the method and assumptions used in estimating these increases, and the contains the results of the estimation. 1.2 SMELTER INFORMATION The smelters used in this study were identified by the Bureau of Mines (BOM) and are listed in Table 1.1. Also included in Table 1.1 are the electric utilities that serve these smelters. Compliance costs were estimated for these utilities. Some of the utilities are unique in the way that the information is handled or in the way the utility is operated; these are discussed below. 1.2.1 Big Rivers and Associated Co-ops, Data for Big Rivers and Associated Co-ops were gathered by George Mason University (GMU) students for BON and are included in this study.

Jan 1, 1988

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By S. S. Venkata

This volume describes a comprehensive program of research into the reliability of mine electrical power system components and the resultant reliability of the total system. The research effort encompassed analytical models, laboratory testing and field testing. The analytical work included definition of terms, fail rate functions and distributions, failure rate estimation and techniques and procedures for theoretical reliability assessment. One of the primary mine power system components addressed in the study was the ac molded case circuit breaker. This device is known to have low reliability and hence an unfavorable impact on mine safety and productivity. Ac molded case circuit breaker reliability was studied by analytical means, laboratory testing and field monitoring. A similar three-pronged' effort was made to study the reliability of undervoltage relays/releases. Particular emphasis was placed on new solid state undervoltage relays. The reliability of bulk power components, such as trailing cab les, motors, control gear, and other equipment, was assessed by gathering maintenance records from active mines. These data were compared to similar records from other industries. The work was extended to include the reliability, availability, maintainability and safety of these components.

Jan 1, 1979

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By Howard W. Wainwright

This bibliography was compiled by the Bureau of Mines as part of an investigation into the possible utilization of low-temperature coal-tar bases. The bibliography consists of literature and patent references from about 1945 to 1961 and is divided into the following headings: Analysis and Composition; Production, Synthesis, Reactions, and Utilization; and Separation, Purification, and Properties. Although over 1,000 references are included, no attempt was made to insure a comprehensive survey. The literature and patent references are arranged alphabetically by author or patentee. When several publications have the same author they are listed in reverse order of age, with the newest first. An author index is included because secondary authors are not cross-indexed. In almost every instance, the entry is accompanied by a Chemical Abstracts reference for those interested in locating an abstract of the original paper.

Jan 1, 1962

By Christopher C. Jobes, Alan G. Mayton

The National Institute for Occupational Safety and Health (NIOSH) researchers have investigated seat design issues for the occupants and operators of underground mine transport vehicles relative to whole-body vibration (WBV) and mechanical shock. Considering the ergonomic and engineering improvements made to underground mine shuttle car seats, this study has focused on reducing injury risk by improving seating on transport vehicles such as scoops, mantrips, personnel carriers, and rail-mounted locomotives. Similarly, proposed seat design improvements included layering of various types of viscoelastic foam padding to isolate vehicle occupants and operators from adverse health effects of jarring/jolting exposure. This paper discusses the results obtained from laboratory vibration testing of new seat padding materials in seven configurations at the NIOSH – Pittsburgh Research Laboratory (PRL) showing that careful use of configuration and materials can reduce the operator’s exposure to WBV. In addition, results for four mine transport vehicles are presented from field data collection efforts at a Southwestern Pennsylvania mine showing that a NIOSH based design does reduce the operator’s exposure to WBV. Finally, the authors discuss efforts to develop and field test seat padding interventions using new padding materials and configurations based on the laboratory test results [The findings and conclusions in this report are those of the author(s) and do not represent the views of the National Institute for Occupational Safety and Health.]

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968