Search Documents

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By A. Singh, R. D. Govender

The current method employed to quantify the efficiency of separation of ferromagnetic ores by wet low intensity magnetic drum separators (WLIMS) incorporates the use of a conventional benchscale Davis Tube (DT) operating at a magnetic field intensity that is equivalent to that of the drum’s surface. However, empirical research has indicated that the magnetic force, or force index, rather than the magnetic field intensity, is the critical factor in the operation of the magnetic separator (Murariu and Svoboda, 2002). Furthermore, the current aforementioned practice would yield incorrect information as the magnetic field gradients produced by a typical WLIMS unit differs considerably from that of a bench-scale DT. In light of this, research on magnetite focusing primarily on the scale-up of DT results to pilotscale WLIMS were undertaken. The investigation entailed a comparative study between that of a typical WLIMS circuit and a bench-scale DT. The purpose was to practically evaluate the performance of a WLIMS, bench-marked against the traditional laboratory-scale DT unit. Moreover, the secondary objective was to produce a magnetite concentrate graded at 69% Fe, 95% -45μm, as a suitable source of separation media for use in the Dense Medium Separation (DMS) industry. Fundamental findings of previous works provided a framework for the study, however, a realworld approach was explored. Preliminary testwork conducted at Mintek investigated the performance of a DT and a typical multi-stage laboratory-scale WLIMS circuit (operating at 1000 Gauss at the surface). The results attained indicated that a DT operating at high intensities is comparable to a single rougher WLIMS stage. Additionally, it was observed that the three stage laboratory-scale WLIMS circuit performed similarly to the DT operating at 1000 Gauss. Moreover, piloting testwork was undertaken, carried out in larger 380mm drums, and the results attained showed a strong correlation with laboratory-scale findings. Keywords: Davis Tube, wet low intensity magnetic separation, magnetite

Jan 1, 2020

One of the important facets of The South African Institute of Mining and Metallurgy is its service to its members. One way of achieving this objective is by pursuing an active branch structure. In this Spotlight, Richard Beck, Holder of the Regional Development Portfolio, gives the aims of the Institute's branches, with a short note on each branch prepared by the regional chairman. Aims of the Branches: The primary aims of the Branches of The South African Institute of Mining and Metallurgy are those of the Institute itself: to further the interest of its members, to uphold the status of the mining and metallurgical profession, and to promote the image of mining and metallurgy. Beyond these 'high' objectives, the branches have a special function in providing a more intimate relationship between the Institute and its members. The branches enable members who live outside the Johannesburg area to participate in the affairs of the Institute to an extent that would not otherwise be possible and that they themselves can define. This is achieved through the holding of social events, colloquia, and visits.

Jan 1, 1990

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By H. Scott-Russell

Ladies and Gentlemen. It is my great pleasure on behalf of The South African Institute of Mining and Metallurgy and The Geological Society of South Africa to welcome you to the 15th CMMI Congress and to Southern Africa. It is a great honour to be hosting this event and we have been looking forward to it for a long time. I am sure the technical discussions and visits will be of great value, and I am confident you will return with pleasant memories of places and people in South Africa and neighbouring countries. The theme of this Congress, Resources and Technology', is appropriate for discussions on the ways and means of going forward in the minerals industry to create the employment and wealth so sorely needed in this region. The technical programme will give mineral industry professionals from different parts of the world the opportunity to share experience and expertise for the purpose of making operations more productive, safer and environmentally acceptable to the world at large. Delegates will be exposed to current technical developments by means of 133 papers prepared for the congress: 30 on geological subjects, 45 on mining, 29 on extractive metallurgy, and 29 in the field of metals technology.

Jan 1, 1994

Professor R. P. Plewman graduated with a B.Sc. in mining engineering from the University of the Witwatersrand in 1943, after which he had two years of military service. Mr P. W. J. van Rensburg attended St Andrew's College in Grahamstown before proceeding to the University of the Witwatersrand, where he obtained a B.Sc. (Eng.) degree cum laude in mining and metal. lurgy at the end of 1942 and was awarded the Chamber of Mines Scholarship and Gold Medal. Dr M. G. Atmore, Deputy Technical Director of the Anglo American Corporation of South Mrica, is also Manpower and Education Adviser to the Chamber of Mines of South Mrica and a Visiting Professor at the Imperial College of Science and Technology, London. Mr D. A. Vi1joen attended Queen's College, Queenstown, and then Rhodes University, where he gained a diploma in chemistry and a B. Comm. degree. Mr B. E. Protheroe, C.Eng., obtained a degree in Physical Metallurgy at University College, Cardiff, and an M.sc. in corrosion science from Swansea University. Mr N. J. Devine holds a B.Sc. in Metallurgical Engineering and a G.DE Mining Engineering, both from the University of the Witwatersrand. Dr Oskar Steffen graduated as a civil engineer at the University of the Witwatersrand in 1961, and obtained his master's degree in 1963.

Jan 1, 1984

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

A party of some 60 members of the Institute were welcomed at the Union Junction Works of Scaw Metals Limited on Thursday, 23rd January for a morning visit. Dr J. M. Bereza, the metallurgical Director, gave an informative introductory talk to the assembled visitors, which briefly covered the major activities of the Company. This was followed by refreshments, and the visitors were then allocated to 12 guides for the conducted tour of the Works. The progress of the Company is an impressive saga of the development of heavy industry in this country linked primarily to the expanding mining industry. Many other outlets are now available for Scaw products and the rapidly advancing techniques developed by their own chemists as well as the processes made available from overseas associates indicates the forward looking attitude of the Company. The visitors were impressed by the modern laboratory services, closely linked to rigid quality control, resulting in a high standard of final products. The most fascinating section to many of the visitors was the continuous casting machines and rolling mills recently installed, although the most lucrative section is the large steel foundry. After the tour the parties gathered in a marquee tent for liquid refreshments, followed by a lavish luncheon in the canteen. The visitors were officially welcomed by Mr Richard Boustred, the Deputy Managing Director, and Mr V. C. Robinson replied, thanking the Company on behalf of the South African Institute of Mining and Metallurgy. Arrangements were made for golf in the afternoon at the Germiston Golf Club for those who wished to play. A.E.G.

By J. K. Williams, M. P. Wells

"As part of the planning system at each division of Nchanga Consolidated Copper Mines, Limited, the Mine Planning Department is required to produce a detailed production schedule for each shaft.Because of the difficulties in producing a schedule which satisfies all the mining constraints, and because of the large clerical effort involved, the full range of possible schedules can never be considered.It has been found possible to produce a schedule using linear programming which satisfies the majority of the many varied mining constraints. Computer programs have been written to enable the mine planning department to use this mathematical system without assistance.The system has a large degree of flexibility to enable the planner to include conditions which cannot be incorporated readily in the linear program. This system permits the more efficient production and evaluation of schedules and reduces the amount of clerical effort."

Jan 1, 2014

The February General Meeting of the Branch was held in the St. Helena Club at 8.00 p.m. on the 10th February, 1971. Mr G. Y. Nisbet (Chairman, O.F.S. Branch) was in the chair. There were also present: Seven Fellows: Messrs. N. A. Honnet, C. J. Isaac, J. M' Meyer, I. Thomas (Committee Members), J. Lorenzen, S. L. S. Swart and D. Waterman. Six Members: Messrs. R. Campbell, D. J. Couperthwaite, R. Cross, A. H. Edwards, C. G. J. Vermeulen and G. J. C. Young. Two Graduates: Messrs. J. McLuskie and M. H. Smith. Six Associates: Messrs. J. Dean, W. F. de Lange, J. S. Freer, A. Hooper, A. Paschalides and L. Vorster. One Student: Mr D. J. Hammond and nine visitors, a total attendance of thirty-two. Minutes As the minutes of the General Meeting held on the 17th November, 1970 had not yet been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. Office-bearers The Chairman informed the meeting that this branch had received the resignation of Mr J. N. Saunders. Following his resignation the Committee elected the following office-bearers: Chairman - Mr G. Y. Nisbet Vice Chairman - Mr J. M. Meyer The Chairman also announced that Messrs. J. M. Meyer and G. J. C. Young had been co-opted onto the Committee. General Members were advised that arrangements had been made for the Cookhouse Tunnel visit towards the end of March. Talk by J. Freer The Chairman called on Mr J. Freer to deliver his talk on "Uranium Extraction, Processing and Conversion for Fuel Element Manufacture". The presentation of this talk, illustrated by sketches, proved very interesting and entertaining and was received with applause from all present. Mr I. Thomas proposed a vote of thanks to Mr Freer on behalf of all members of the O.F.S. Branch. After thanking Mr Freer for his talk and all present for their attendance, the Chairman declared the meeting closed at 9.30 p.m.

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By L. Bloch

Most mine safety initiatives in South Africa are doomed to limited success because of one simple fact: they are a-historical and un-cultural and do not deal with the serious ?legacy issues? that still negatively impact on safety, production, and relationships. We in the SA mining industry continually use imported, foreign safety concepts and systems that will not work fully in a South African context. ?The 4th Wave: Culture-Based Behavioural Safety?, as developed by Lance Bloch, an international award-winning clinical psychologist with 12 years? experience in the mining industry - focused mostly on Platinum - is making waves. He has been very successful in creating people-centred, empowered, high-performance safety cultures wherever he has worked. Not only does the 4th Wave transform the corporate culture of a mine, improving safety and production and building an environment of Ubuntu, but it also uses people?s cultures as a means of winning hearts and minds in the battle for safe production. Powerful relationships are built through engagement at all levels, leading to all being focused on the best needs of the company and its constituents as a whole. The programmes are no less than nation-building - something most necessary in the industry, with the pressures from community, unions, the DMR, and politicians. This presentation will describe and discuss the 4th Wave as an advance on previous safety technology and programmes, as particularly relevant to platinum mining in South Africa today.

Jan 1, 2012

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By J. H. French, O. E. Lissner

S. J. Venning (Member): The authors should be congratulated on producing such concise data from the plethora of experimental report results. Their observations on the cost of liners calls for some comment however, as the really unique feature about liners in South Africa is that they can be obtained so cheaply. Attention has been focussed on the 1961 cost of white iron at R50 per ton for chill cast block liners while manganese steel liners are reported as costing as much as R250 per ton. The former are however, a relatively heavy, simple casting with a low labour content and reasonably high percentage productivity, made from metal melted in a cupola. The capital investment to produce this type of casting is low compared with that required to produce manganese or other alloy steels. The chill cast liner block is always a production item and is cast in a permanent mould. Almost all manganese mill liners, except perhaps small aperture screens, are sold for considerably less than the R250 per ton quoted by the authors. Where a price of this nature is asked it would be because the design of the casting demanded is complicated or leaves little metal to carry the labour and other costs of production. As reference has also been made in the paper to liner costs in America, prices for similar types of liners obtained during a visit to Canada and the U.S.A. in 1961, could be of interest: Material Price per Location short ton Ni-hard R250 Elliot Lake Body liners block type Ni-Hard R300-310 FAS New York Mn Steel R280-290 FAS New York Screens (grids) slotted Cr.Mo. Steel R600 FAS New York hole Ni-Hard R320 Elliot Lake At this time the price of comparable manganese steel block type liners on the Witwatersrand was between R145/R155 per short ton. White iron in Canada was then quoted at about R150 per ton, but as Ni-Hard gave a life of at least two to twoand-a-half times that of white iron, it was a much more attractive proposition particularly when relining and down time costs were taken into consideration. There is little doubt that most foundries would welcome clear and complete specifications of the customers requirements and systematic checks to ensure that these specifications are being met. B.S.S. or other accepted standards should form the basis of these, and periodic inspections should be undertaken to ensure that only those foundries capable of complying should be included as suppliers. The authors have referred to new designs, but can the industry really call the grid and plate new when the patents were taken out during the second world war and the sawtooth block has been used for at least 35 years. Unfortunately, far too little thought and consideration are normally given to the ultimate mill liner design while the mills themselves are on the drawing boards. The position and size of the door opening, which is the key to the ultimate shell liner configuration, the drilling of the

Jan 9, 1968

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020