Search Documents

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

By N. Saldía, C. Riveros, R. Hills, S. Barrera

The transport of tailings composites provided by different sources is a field of study where a limited amount of research has been conducted. Nevertheless, such systems are important sources of operational difficulties, especially in the case of high clay content tailings. The case presented in the present paper consists of a free surface flow pipeline transporting a composite of two different tailings with high clay content. It has presented operational difficulties such as partial blockages and upstream box and air intake overtopping events. In the present paper, the causes of these difficulties are identified. These include lack of complete mixing of the different tailings, multi-layered flow with low velocity and high yield values with high frictional losses. The pipeline characteristics and performance are analysed in three stages: design, initial operation and enhanced operation, the latter accomplished by means of increasing turbulence in the box located upstream from the pipeline. The last section of the pipeline and another distribution pipeline system located downstream from the pipeline have performed well. The cause of different behaviour of both systems is also assessed.

Jan 1, 2007

By B. B. Mamba, J Ndalamo

The existence of an impressive reserve of oxidized cobalt-copper bearing ores in the African copper belt area lead the GECAMINES (DRC) to develop specific and adapted mineral processing routes (Mulaba-Bafubiandi, 2001). During the conventional diluted sulphuric acid leaching of oxidized cobalt-copper bearing ores commonly referred to as ?heterogenite?, more than 10% cobalt dissolution yield increase was observed in a plant situation (Mwema et al., 2002) when SO2(g) was flushed into the acidified cobalt leaching solution. The present paper attempts to elucidate mechanisms involved which lead to the increase of total cobalt as SO2 is flushed during the leaching of oxidized cobalt bearing minerals. The kinetics of cobalt dissolution as SO2 is flushed into the acidic solution as well as a full characterization, using UV-Visible spectroscopy, of Co2+ and Co3+ species present in the collected leachate are presented while possible effects of the presence of Cu and Fe on the leachability of cobalt bearing minerals present in the oxidised ore will be discussed. In the view of speeding up the leaching process, the mixed cobalt-copper oxidised ores were microwaves pre-processed. Preliminary results were also discussed.

Jan 1, 2007

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project's life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

By P. De Kock

Strategic mine planning is concerned with the decisions that determine the value of the business, while tactical planning deals with the tasks to realize that value. When tasked with formulating a strategic mine plan, the mining engineer often turns to commercially available software. However, these software packages have limited applicability to the RBM situation. Adopting a simpler, back to basics approach founded on a deep understanding of the economics of the orebody has the advantage of providing a clear logic to guide tactical planning. By creating a coherency between strategic mine planning, and tactical planning the likelihood of successfully executing the plans and attaining the value promised by the strategic plan is increased. This paper describes the reasons why RBM embarked on a strategic mine planning process, the rationale of choosing the process, and the process itself.

Jan 1, 2007

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

This paper presents a quantitative approach to the problem of determining design capacity and field dimensions of underground coal mines using room- and-pillar mining systems. In evaluating these design variables, relationships among mining costs, number of production sections in mines, location of central shafts, mine field dimensions, section production, mine output, and cost of production losses due to underground man-traveling are analyzed. Thereby the unit cost of coal is expressed as a function of the design variables as well as input parameters such as seam angle, seam thickness, seam depth, underground traveling speed of men, mine recovery and plant recovery. The problem is then formulated as a nonlinear optimization model in terms of minimizing the unit cost of coal subject to a set of constraints and solved analytically for flat seams and numerically for inclined seams. Sensitivity analysis of the variables is also included in the paper.

Jan 1, 1987