Search Documents

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

In a gravity separation device, particle shape, size and density all play a role. The combination of these determines where each individual particle reports to in the viscous fluid, where particle crowding (solids to water ratio) also plays a role. To understand the performance of gravity separation devices in the heavy mineral industry, these particle characteristics need to be measured. There are various challenges in analysing particle density and particle size simultaneously for the purpose of quantifying gravity separator performance, not to mention particle shape. These analytical challenges include the high cost of high-density sink-float fractionation, toxicity of high-density sink-float media, inability of sink-float media to fractionate at densities greater than 4.0 g/cm3, and the time-intensive nature of these fractionations. The use of the detailed particle-by-particle output from Qemscan® particle mineral analyses (PMA) as a fast and cost-effective alternative is evaluated. The size and density outputs from the Qemscan® were employed to characterize the performance of a heavy mineral spiral concentrator as an example. Critical analytical requirements are to be addressed before the Qemscan® output data can be utilized. Keywords Gravity separator, performance, heavy minerals, Qemscan® particle mineral analysis

Jan 1, 2011

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By S. J. Swart

This paper discusses the principles and application of risk assessment and management as the basis for environmental management within the mining industry. Unlike in other industries, mines are required to obtain closure certificates in terms of section12 of the Minerals Act, which should ultimately release them from further environmental responsibilities. It is emphasized that the concept of environmental risk assessment and management, when applied correctly will mean that the mine will be identifying and managing environmental issues beyond those set by current legal requirements and management strategies. The focus shifts from conventional minimum legal compliance management to management of real environmental risks. The advantage of this approach is that the perceived ?shifting of legal and management goal posts? due to changing environmental laws or management principles, will not influence or dictate the mine?s short or long-term management objectives or actions, mine closure funds can be more accurately determined and mine closure should become a relatively simple procedure. The risk assessment approach has been applied to the planning of mine closure at Iscor?s Durban Navigation Collieries (Durnacol) in Kwa-Zulu Natal and certain key risk issues such as the long-term risk of water pollution from coal discard dumps have already progressed to fully quantitative risk assessment. This paper will discuss the process, which has been followed to date, with particular emphasis on the most recent phase, namely quantitative risk assessment and management of pollution from coal discard dumps. It is believed that the approach that is being pioneered at Durnacol and which overcomes some of the more obvious deficiencies of both the EMPR and the traditional IEM process will ultimately serve as the model for all responsible mines in South Africa. It is also believed that this approach will enable the authorities to issue closure certificates with the confidence that there will be no unforeseen surprises in the years after closure.

Jan 1, 1998

By R. A. Harris

In this study Pt-Al thin films were prepared via electron beam physical vapour deposition (EB-PVD) with an atomic concentration ratio of Pt25:Al75. These films were heat treated at temperatures ranging from 150°C to 650°C for annealing times from 4 to 60 minutes. The resulting microstructure of these thin films were obtained via secondary electron imaging used in conjunction with depth profiling with the aid of scanning auger microscopy (PHI 700).Elemental maps of the micrographs were obtained. Simulations, based on a chemical potential Monte Carlo method1, were run for various interaction parameters. From these simulations theoretical depth-profiles and proposed microstructures were obtained. These were compared to the experimentally measured depth profiles and elemental maps. Keywords Monte Carlo, chemical potential, depth profile, Pt-Al thin films.

Jan 1, 2011

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

A low noise blast hole drilling system was developed to limit the risk of noise induced hearing impairment in mining operations. Noise induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise induced hearing. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard Seco S215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock shavings, oil and grease) is removed from the encapsulating tubes via exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2003