Search Documents

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By Ivan Weber

Asking the question, “What do the world’s leading corporations and cutting-edge practitioners of sustainability put forth to guide a given mine site for planning and action toward ‘sustainability’?”, this paper explores the spectrum of methodologies and mindsets in available literature, then constructs an example for the large near-closure facility at Kennecott Utah Copper. Values, opportunities and constraints spring from physical, unutilized byproducts, from critical ecosystems and wildlife populations, from location relative to those ecosystems and proximate communities, and from the political will to perform adequate feasibility investigations. Patience, determination and thoroughness are imperative. Identifying most productive and, simultaneously, most protective and restorative, practical methods to approach ‘sustainability’ has become a central mission of industry and business, worldwide. A survey of recent international initiatives finds no single approach that establishes either a readily adaptable methodology or an appropriate set of ‘attention’ points, or agenda, to guide individual mining operations at specific locations toward the elusive but essential goal of ‘sustainable’ mining. Untying this convoluted knot of contending factors requires willingness to recognize and work within ecological constraints for community long-term needs. Occasionally, the task requires the sword of Alexander the Great. Through integration that is unflinchingly honest ethically, culturally, economically, ecologically and scientifically, fully cognizant of place and community at whatever scales are of greatest significance, and integrative of both problem-response and opportunity, we may envision a mineral extraction and beneficiation future that achieves the best, most nearly sustainable, results possible. Industrial ecology (IE), with its clear emphasis on community, ecosystems, and sustainable economic stimulation, presents a sufficiently broad and adaptable discipline to facilitate planning and management toward sustainable mining. The creation of sustainable jobs encapsulates IE’s analogy to the niche survival strategies of organisms in nature. Open to common-sense recognition of faults and opportunities at appropriate scales, IE is less a discipline or prescribed methodology than a mindset, willing to be rigorously scientific when science is imperative, but also willing to exercise “art” when creativity or community engagement are needed. IE is also capable of future-looking compassion for peoples and nature. Looking beyond what has occurred to date, the case of Kennecott Utah Copper provides ample illustration of possibilities for community economic development, environmental management, and significant initiatives beneficial at regional and planetary scales, to become recognizable as deserving of the label, ‘sustainable.’ Through what this researcher terms “whole mine, whole region, whole planet” thinking, strategies become visible and subject to serious consideration, presenting a path to best possible accomplishment in mining. Constituting a maximal broadening of mining’s “traditional” scope, the integrative approach proposed here is the ‘paradigm shift’ being made by many other industries around the world. In aggregate, these steps are the only hope for avoidance of environmental, social and economic risks that threaten to curtail resource development and impair mining companies’ ‘social license to operate.’

Jan 1, 2005

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health (NIOSH) from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health. At both deep and shallow cover instrumentation sites, surface subsidence measurements, subsurface in-place inclinometer measurements, and underground pillar pressure measurements were conducted as longwall panels were mined. Comparisons of the deep and shallow cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario. Under shallow and medium covers, measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Conversely, measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers. However, FLAC3D simulations of the casings indicate that, in all three cases, the P-110 production casings remain intact under longwall-induced deformations and compressions, which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.

Jan 7, 2020

By Arthur D. Silber

The economic success and growth of any metropolitan region depends on mobility. Today, mobility between New Jersey and New York is threatened by a transportation system that cannot meet 21st century travel demands. The transportation bottleneck created by the Hudson River threatens the viability of one of the world?s great centers of commerce and culture. Fortunately, there is a solution: The Access to the Region?s Core Mass Transit Tunnel. The US$8.7-billion Mass Tran-sit Tunnel?s (MTT) new two-track line will double commuter rail capacity under the Hudson and create a new, state-of-the-art cavern station in Midtown Manhattan, with wide platforms, high-speed escalators and other features to improve riders? travel experience. The capacity and other benefits of the MTT project will launch a new era of prosperity for the region, just as the Pennsylvania Railroad did almost 100 years ago when it built the existing two, single-track rail tunnels that now form the sole commuter rail link between New Jersey and New York. The existing tunnels run from North Bergen, NJ, under the Hudson River to Pennsylvania Station at 33rd Street in Manhattan. Construction on the MTT, the largest public works project in the United States, is scheduled to start this year and continue through 2017. The MTT is ready to go to construction thanks to a major commitment of financial, engineering, project management and other resources from NJ TRAN-SIT, New Jersey?s statewide mass transit agency, and the Port Authority of New York and New Jersey, a bistate agency that operates the Holland and Lincoln tunnels, the George Washington Bridge and other major transportation facilities in New York and New Jersey. The project is also strongly supported by the state governments of New York and New Jersey, as well as that of New York City. The MTT is New Jersey Governor Jon Corzine?s number one transportation priority.

Jan 1, 2009

P&H MinePro Services Canada is supplying Syncrude Canada three more of its model4100BOSS electric mining shovels. The shovels will be delivered during 2003. Syncrude’s oil sands operations already use five P&H shovels. The first 4100BOSS shovel was commissioned at Syncrude’s operation in northern Alberta, Canada in October 2001. The unit loads more than 9 kt/hr (10,000 stph) of unblasted oil sands. Since it began operation, the 4100BOSS has shown a 28% production increase over the four P&H 4100TS shovels also on site.

Jan 1, 2003

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By S. Devasahayam

Acid production or acid drainage is a major environmental issue that also has negative implications on the aquifer system surrounding the mine tailings area. The approach to controlling acid mine drainage involves physical and geochemical characterization that affect acid production. The material permeability determines the availability of oxygen, which is paramount in acid production in coal rejects, and varies with depth. In this paper the author presents the variation in oxidized pyrite/acid production with depth in black coal mine washery wastes. Chemical kinetic parameters and the diffusive parameters have been used to obtain the variation in oxygen content and the oxidized pyrite content with respect to the depth and time. Its dependence on porosity and moisture content is illustrated.

Jan 1, 2007

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By O. A. Lima

Effective solids suspension is a necessary precondition for particle collection, and solids suspension is largely dependent on the hydrodynamics of the flotation cell. This study attempted to correlate the status of the suspension of apatite particles of different sizes in a Denver laboratory flotation cell versus the impeller rotational speed (N) adopted to operate the machine. The latter variable (N) influences the impeller capacity to lift the particles from the bottom of the tank and also to disperse them throughout the volume of the vessel. Such an impeller capacity can be characterized by the critical impeller speed for the accomplishment of solids off-bottom suspension (Nz) and also by the velocity of the radial water flow discharged by the impeller (U) divided by the particle terminal settling velocity (Us). This way, the status of the suspension of apatite particles inside the flotation cell can be characterized by one of three categories: ?segregation? (N/N2 < 0.60 and Us/U > 0.08); ?suspension? (0.60 = N/N2 < 1 and 0.06 < Us/U < 0.10); and ?dragging? (N/N2 = 1 and Us/U = 0.03). The range of impeller rotational speed (N), which was able to suspend the finest particles (Dp = 90 µm), was unable to suspend the coarsest particles (Dp = 254 µm). Conversely, the high value of N (N > 1,300 rpm), which is adequate to suspend the coarsest particles, may promote the entrainment of the finest particles to the froth layer.

Jan 1, 2009