Search Documents

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

By I. Koliabina

In this paper, the results of mathematical modeling of casing pipes decontamination from radio-active new mineral forms directly in boreholes using hydrochloric and hydro-silicic-fluoric acids are presented. Modeling for highly and low radioactive coatings on the walls of casing pipes of Anastasievka oil-and-gas deposit was performed using GEMS software, based on the method of Gibbs energy minimization. Calculations have shown that thorianite and goethite, that are present in low-active crusts, detected in casing pipes uplifted from comparatively low depths, are well dissolved in hydrochloric acid, but radiobarite is almost insoluble. For the same acid concentrations, almost all radiobarite of high-active coatings detected in pipes uplifted from considerable depth is dissolved. To evaluate the possibility of decontamination of pipes from radiobarite of low-active coatings, modeling of crust dissolution under the action of H2SiF6 has been performed. The results have shown that for acid concentrations of more than 13 % almost all Ra and Ba are dissolved while all iron and thorium remains in goethite-thorianite solid solution. For the same acid concentration, almost all radiobarite from high-active coatings is dissolved. Therefore, no reagent allows decontamination of pipes from coatings of both types. It seems that successive or simultaneous use of both reagents (HCl and H2SiF6) in certain ratio is required. To clarify this issue, further experimental and model investigations are necessary. The issue of decontamination of casing pipes from galena that is present in high-active crusts also needs to be clarified.

Jan 1, 2005

By Milton E. Wadsworth, M. Ken Han

The kinetics of leaching of galena in hydrochloric acid solutions with sulfur dioxide gas have been investigated experimentally. The leaching method is then applied to complex sulfide concentrates to evaluate its selective leaching capability and to develop a new hydrometallurgical lead extraction process based upon the method. The leaching reaction follows a linear rate with an activation energy of 61.9,KJ/mole. The rate Is of first order with respect to the product [H+] [Cl-] . Excel lent selective leaching capability f s demonstrated and an attractive hydrometallurgical process flow sheet is proposed.

Jan 1, 1989

By Henry Antwi

The decade of the 1990s promises to be one of increasing internationalization for domestic minerals producers as they scramble to enhance relative positions in highly competitive, international minerals markets. This "international mining rush" is fueled by developing countries seeking international investment capital to explore for, develop and exploit sizable mineral endowments in an attempt to support the increasingly popular, but expensive, wave of democracy and selfdetermination sweeping the world. This "fuel" typically takes the form of revised mining codes and, often, lucrative investment incentives. These incentives include favorable tax rates, royalty provisions, relaxation of import/ export constraints, depreciation schedules, profit repatriation and other variables that can positively impact mineral investment decision making. Concomitantly, in their attempts to address real and perceived short- and long-term woes associated with enhancing competitive positions internationally, many domestic explorers and producers are attracted to the prospect of finding high-grade deposits in relatively virgin areas. Combined with the investment incentives provided by foreign governments, these high-grade deposits promise lucrative potential returns from projects having short payback periods. Classic examples of this mutual desire to intensify international mining efforts by domestic producers are illustrated by activity levels in countries like Chile, Bolivia and Venezuela in Latin America and, more recently, in Eastern Europe and select locations in the former Soviet Union. As US corporations scurry to send fact-finding, technical, evaluation and financial teams to these presently popular locations, one area of the world has received little attention - Subsaharan Africa. Specifically, the country of Ghana (formerly the Gold Coast) deserves more attention than it appears to be receiving from North American mining companies.

Jan 1, 1992

By Herbert Pöllmann

The mineralogical and chemical compositions of various waste materials undergo different reactions when treated thermally The heavy metal contents can be bound to stable phases. These minerals are called reservoir minerals. The main property of these minerals is the stability in their geochemical surrounding containing the heavy metal cations and anions. Examples for these minerals are apatites, spinels, garnets, perovskites and also water containing minerals like ettringites, metal-metal-hydroxi salts, jarosites and zeolites. When the chemical compositions of different wastes are mixed according to the compositions of the new formed minerals, a probable reuse of these wastes can be obtained. The use of waste incineration ashes for the production of cementitious binders and the use of flue gas desulfurization products for cement additives are shown. Also the transformation of highly contaminated materials into stable reservoir mineral assemblages are shown including the study of stabilization and immobilization techniques.

Jan 1, 1998

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By Christof Brewka

Los Pelambres, 200 km north of Santiago, Chile, is the latest in a series of mega-projects developed in this part of the world. While most of its predecessors are spread over open desert, the Los Pelambres mine is nestled inside a narrow alpine valley high in the Andean Mountains. To handle the daunting task of transporting the mined copper ore more than 12 km and 1,400 vertical meters downhill to the concentrator plant, a gigantic belt conveyor system (capacity of 8700 mtph, 1800 mm wide ST 7800 steel cord belt, 2.5m diameter pulleys, an elaborate braking system including a mechanical failsafe and large reducers with a total installed drive power of 25,000 kW) has been employed. Many of these components have pushed the limits of conventional belt conveyor design.

Jan 1, 2000

By A. W. Khair, M. Ahmad

Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion, oxidation, or diffusion, depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been camed out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation.

Jan 1, 1992

By Nigel Pearson, Malcolm J. McPherson

In the Grasberg Mine, a series of orepasses of diameter 2 to 4m are being constructed, each one to carry as much as 10,000 tlhour of copper- and gold-bearing ore through single stage vertical drops of over 500m. At the base of each orepass, the fragmented rock falls into an orebin of diameter 1 Om and 100m deep. Long before the planned tonnages were reached on the early orepasses, a problem arose that was both serious and intriguing. Pressurization of air in the orebins caused by the falling rock reached such levels that when the feed to the top of an orpass was interrupted, a massive surge of air ascended rapidly and produced a dangerous backblast accompanied by dust; grit and rock fragments from the top of the orepass. Backblasts lasted for about one minute and were not only hazardous to the health and safety of personnel but also required time-consuming clean-up operations. The paper describes the aerodynamic analyses that were con- ducted in order to understand fully the mechanisms involved in the phenomenum, and the development of a procedure that al- lows the effects of falling material to be incorporated into existing ventilation network software.

Jan 1, 1997

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By S. Eugene Sankey, Geoffrey L. Payne

Modern metallurgical processing often depends heavily on the use of flocculants to achieve the high levels of efficiency required. Selection of the optimum polymer can be complicated by the effects of process streams on the chemical and physical stability of the chosen polymer. Similarly, the presence of the polymer can have positive or negative side effects on process streams, such as phase disengagement in solvent extraction, foaming at filters and thickeners, crystal growth modification or flotation performance. Guidelines are given to highlight areas where problems may occur and suggestions made as to how these can be overcome. Practical advice on the preparation and application of polymers in process liquors is provided.

Jan 1, 1986

By B. Ainsworth

The 1972 discovery of the Howards Pass lead-zinc deposit was the product of systematic regional geochemical surveys used to evaluate conceptual geological models for the metal-rich black shales of the Selwyn Basin. Motivation of personnel involved in all aspects of work was as critical a factor to the success as the existing corporate attitudes and infrastructure. Exploration programs were flexible but maintained a focus only on targets of sufficient economic potential to support operations in remote locations. Direct costs for the programs that lead to the discovery were in the order of $500,000 (Canadian 1972). Geological reserves today stand at over 500 Mt (511 million st) of 7% combined lead-zinc, containing a higher grade zone of nearly 10 Mt (11 million st) of 16% combined lead-zinc.

Jan 1, 1991

By Enrique Farjeat P.

Mexico City's growth has encourage development of underworks to meet drainage and transport requirements. Deep Drainage System has been constructed through a complex tunnel network, 108 km in total, varying from 30 to 12 m in depth and 6.24 or 4.00 m in diameter. Wide range of stability conditions presented in soils has forced the use of several tunnelling methods, going from the manual procedure by the use of pneumatic tools, to slurry shields, or open face shields, with the aid of or without compressed air. For transport, subway tunnels have been excavated in very compact silty sands, 9.15 and 9.51 m in diameter, with the use of open shields one of which was designed by Mexican engineers as a prototype machine. This paper tries to describe evolution of tunnelling methods used in Mexico City during last 20 years.

Jan 1, 1991

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

By D. B. Jenkins, D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity that exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into a worldwide business with a capacity of about 500 kt/a. This paper will present data on the chemistry, mining, manufacturing, and applications for acid-activated clays.

Jan 1, 1988

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By J. C. Norman

The boron review arrived too late for the June issue. The United States was the world's largest producer and consumer of boron compounds during 1993. Boron mineral concentrate and chemical production in the United States totaled an estimated 958 kt (1.05 million st), yielding 526 kt (580,000 st) of B203, according to the US Bureau of Mines. Estimated value was $322 million. This level of production was about 5% less than 1992 revised production figures. The United States continued to provide essentially all its own boron while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1993 was 900 people, about the same as in 1992. That was down from 1988 levels of 1250 people. Total world production of boron in 1993 was about 2.5 Mt (2.75 million st), yielding about 1.2 Mt (1.3 million st) of B203. World production in 1993 was about equal to revised 1992 levels. Production United States In 1993, mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. Domestic producers, in order of quantity of production, were: • US Borax and Chemical Corp., which operates an open pit kernite and tincal mine at Boron, CA, producing boric acid and borax products, • North American Chemical Co., which produces boric acid and borax products as coproducts from chemical operations at Searles Lake, CA and • American Borate Co., which produced small amounts of colemanite and shipped from inventories from its operation in Death Valley, CA.

Jan 1, 1994