Search Documents

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

Jan 1, 2005

By R. R. Tatiya

This paper describes the local estimation of mineral inventory by kriging. A mineral deposit located between two working levels of a copper mine was examined. Data for this estimation was obtained by underground diamond drilling. The mineral inventory that was computed by this method was compared to the results obtained by global estimation techniques, which were based on information front surface boreholes. A comparison between the ore reserves estimated through kriging and the ore reserves estimated at the mine using conventional methods was also made. This analysis shows that geostatistical methods can be applied to evaluate base-metal deposits similar to the deposit examined in this study. In the part of the mine that was examined, the kriging estimates show an overall increase in metal content at all cutoff grades, compared to the estimates obtained through conventional methods. Also, the ore body profiles are more continuous and regular through kriging, but they are not radically different from the profiles that were previously obtained at the mine. However, the global estimate of the deposit using kriging could not provide reliable results.

Jan 1, 1997

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

Lingering effects of the 1990 oil shock that included overbuilding and corporate and individual financial distress caused the Gross Domestic Product to fall slightly to $5.67 billion (US billion = l09). With 254 million people - 697,000 in mining and petroleum - the US has more than 100 million dwelling units and 190 million licensed motor vehicles. New private housing starts fell 15% to one million units. New car production fell 11 % to 5.4 million units. Truck and bus production fell 8% to 3.4 million units. The inflation rate was 3%, while the prime rate of interest was 8.5%. The Producer Price Index (1982 = 100) changed as follows: -fuels and related products and power down 1% to 8l, • metals and metal products down 2% to 120, • chemicals and allied products up 2% to 126, and • non-metallic mineral products up to 2% to 117. Energy Imports of crude and refined petroleum, costing $50 billion, fell 5% to 2.8 billion bbl. Domestic petroleum production rose 1% to 3.6 billion bbl. Petroleum supplied about 39% of US energy, natural gas 24% and coal 22%. The National Energy Strategy was announced in February 1991. Its purpose is to encourage domestic production of fossil fuels and nuclear and renewable energy and to stimulate efficiencies in use. Congress continued to debate the strategy and took no action. Coal production fell 3% to 902 Mt (994 million st). About 60% of that came from surface operations. Seventy-eight percent of the total was used to generate electricity and 3% was coked.

Jan 1, 1992

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By Danqing Xu, A. W. Khair

This paper presents an analysis of mechanism of secondary fragmentation and respirable dust generation due to regrinding. In continuous miners, the recovered coal and uncleaned coal from the previous cutting cycle have to be transported through the circumference of the cutting drum, subjecting the coal to regrinding. Such regrinding comminutes the coal material utilizing kinetic energy, thus creating a great amount of respirable dust. The mechanism of a single particle subjected to regrinding is analyzed. A mathematical model is developed to describe regrinding in field conditions. The important factors influencing the comminution process are discussed in detail. Utilizing three types of coal seams, laboratory experiments are being carried out with an Automated Rotary Coal Cutting Simulator (ARCCS) to quantitatively evaluate the effects of some particular parameters, such as cutting velocity, depth of sump and properties of coal material, on breakage and on the amount of respirable dust generated. An orthogonal fractional factorial experimental arrangement is used to optimize experimental design. Preliminary experimental results are presented.

Jan 1, 1991

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By P. D. Rao, D. E. Walsh, W. W. McClintock

A column flotation system was designed to conduct release analyses on a very finely disseminated, stratiform copper ore from the Denali Copper Prospect in Alaska. Chalcopyrite is finely disseminated in a carbonate matrix, and pyrite is disseminated in both the chalcopyrite and the gangue. Grinding to -20 µm is required for adequate liberation. A 25-mm x 2.4-m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate. The rougher concentrate was then repeatedly floated to produce release fractions. These fractions were analyzed for copper, iron, calcium and magnesium, and release curves were plotted. The procedure was replicated at each of two grinds, i.e., 99% and 88% passing 37 µm (400 mesh). The procedure should find application for flotation characterization and process selection. Bond grindability testing was also conducted.

Jan 1, 1996

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. A strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for online generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in nonferrous mineral processing is presented.

By Ronald D. Mariani, Gregory E. Mahoski

BACKGROUND The steel and iron ore industry has had a long history of an adversarial relationship with its union and workforce. The Empire Mine during its first 40 years of existence was no exception. The "we-they" mentality went hand-in-hand with the normal by-product of an adversarial relationship, grievances and arbitration. This relationship was considered the norm and it was not until the late 1970s that consideration was given to changing this relationship. At this time the industry was involved in a fight for existence and the economic pressure demanded increasing productivity to lower cost. The challenge to survive highlighted the fact that an adversarial relationship was not conducive to attaining the needed gains in productivity. The first formal attempt to change the way we worked came in the 1980 Labor Agreement which provided for the opportunity to utilize Labor Management Participation Teams (LMPTs). LMPTs were established at the Empire Mine and they functioned for a couple of years. The teams spent most of their time working on creature-comfort issues and steered clear of dealing with productivity issues. Mine shutdowns had occurred in Michigan resulting in large layoffs, and the union was trying to add jobs and was not supporting teams that could increase productivity and eliminate jobs. When the 1986 labor negotiations began, the local union pulled their support of the LMPT process. Other initiatives were negotiated over the years to foster a change in the culture but, as with the LMPT program, they did not produce the desired culture change. It became abundantly clear: you cannot negotiate a culture change.

Jan 1, 2004

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By Gary Buchan

During several months in 1996 and 1997, Cyprus Twentymile Coal Co. (TCC) set world production records at its Twentymile Mine in northwestern Colorado. These records were due to the company's implementation of a state-of-the-art longwall mining and conveyance system along with a -highly dedicated work force. This article is a case study of the design of long panels at the mine from conception to implementation. Obstacles that needed to be overcome included subsidence engineering, environmental regulations, conveyance, ventilation, equipment design and continuous miner (CM) development timing.

Jan 1, 1998

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By Michael G. Nelson, Dot J. Helm, Edmond C. Jr. Packee

Under a Section 319 Water Quality grant from the U. S. Environmental Protection Agency, a working group of government agencies, mining industry representatives, and University of Alaska researchers undertook reclamation of an abandoned mine site on Birch Creek, near mile 101 of the Steese Highway. Stream hydrology, water quality, and the extent and nature of natural revegetation, were measured before the site was then recontoured to decrease the bedload deposition and bank erosion of the streams. Methods for stabilization of streams and rivers appear to have much in common with those for locations further south, but are subject to complications unique to the North, such as the formation of aufeiss, and to a lack of accurate climatological data. Natural revegetation appears to be possible for most northern placer mine sites. However, it may take place more slowly than required by public perception. Preliminary data indicate a surprising lack of nutrients in the floodplains of mined areas. Natural revegetation may be enhanced by selective planting of grasses and willows, which will contribute variously to soil quality, bank stabilization, and short-term appearance. Monitoring of hydrologic and water quality data, and of natural and artificially placed vegetation will continue at the .Birch Creek site through the summer of 1995,

Jan 1, 1995

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By R. D. Miller, D. W. Steeples

Application of shallow, seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection and environmental evaluation has been successful in many geologic settings. The increased dynamic range of recording equipment and the decreased cost of processing hardware and software have made shallow, seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m (10 ft) in coal seams as thin as 2 m (6.5 ft) at depths of 200 m (655 ft). Subsurface voids associated with abandoned mines at depths of less than 20 m (65 ft) can he detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt. Complex geologic features associated with deposition of various hydrothermal minerals have been mapped with high-resolution seismic reflection at depths from 80 m (260 ft) to more than 300 m (985 ft). Faults in sulfur-hearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow, high-resolution seismic reflection has the potential to enhance the economics and safety of mine operations.

Jan 1, 1996

By D. K. Sengupta, T. K. Rout, A. R. Prasad, B. P. Singh

The filter cake from the vacuum drum filters of a uranium ore processing plant still contains some leach solution. If the filter cake is not efficiently washed the associated leach solution is lost. Therefore, it is necessary to produce a filter cake that is permeable enough to allow efficient washing. The dewatering characteristics of the solid-liquid system must be improved to obtain flocs with sufficient strength to withstand the suction pressure of the filtration system. To facilitate efficient filtration with minimum cake moisture, studies were undertaken to improve the dewatering characteristics of the cake using different types of flocculants and surfactants. In these studies, flocs were formed with anionic, cationic or nonionic flocculants. The best performance was obtained with a low cationic high molecular weight flocculant. The filtration parameters, namely, capillary suction time, cake resistance, cake permeability and final moisture content of the filter cake, are improved by using a combination of flocculant and nonionic surfactant.

Jan 1, 2002

By G. F. Friel, J. C. Edwards, C. C. Hwang

In the implementation of a mine fire alarm and location strategy, the Interpretation of the fire signature Is Important. Smoke and CO are the two dominant fire signatures, and many mine fire detection systems utilize sensors which respond to smoke or CO through a diffusion mode or a mechanical pump mode. The fire signature may be modified during its transport along airways and at crosscuts. The modification occurs through dilution of the contaminants. In this Investigation, computer codes were employed to compute the effects of contaminant dilution on the contaminant signature when a straight flow passage has one dead-end crosscut. The model predicted the airflow within always and the entrainment of contaminants into the crosscut from the airway. One application of the model is to determine the most suitable location for CO detectors for early mine fire detection.

Jan 1, 1995