Search Documents

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

The present study examined a process for precious metal recovery (silver and gold) from difficult minerals which exhibit refractory characteristics to cyanidation and ammonium thiosulfate leaching (low extraction and high consumption of leaching agent). It is well known that mangano-argentiferous minerals are mainly composed of manganese, silver, gold, and iron. In this research, a mineral sample from Monte del Favor mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay, and atomic absorption spectroscopy (AAS). Two-stage leaching was carried out: first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent and sulfuric acid (H2SO4) and a second stage to dissolve silver and gold with sodium hypochlorite (NaClO) and hydrochloric acid (HCl); the results show extraction around 96% for Mn and 98.73% and 83%of Ag and Au, respectively. The usefulness of high acidity and Na2SO3 to obtain good results in Mn and Ag leaching is discussed along with the roles that HCl and NaClO play in the dissolution of Ag and Au values.

Apr 15, 2020

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By E. M. Hill, H. K. Lin, J. L. Oleson

When activated carbon is used for recovering gold in gold industry, carbon fine materials are generated in stripping, acid-washing and kiln regeneration circuits. The carbon fines at the Fort Knox mine, Fairbanks Gold Mining, Inc., contain up to 0.68 kg/t (20 oz/st) of gold. In laboratory tests, gold in the carbon fines was effectively transferred to coarse virgin carbon when the carbon fines were mixed with virgin carbon in cyanide solution at a cyanide concentration higher than 0.10%. A plant-scale test conducted at the Fort Knox mine also shows effective gold transfer from the carbon fines to virgin carbon with a 95% gold recovery in a two-stage gold transfer process.

Jan 1, 2002

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

By D. S. Yantek, R. J. Matetic, A. K. Smith, E. D. Thimons, J. Srednicki

In a 2007 report to the U.S. Congress, the Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) stated that built-in-place refuge alternatives (BIP RAs) provide significant advantages over mobile refuge alternatives. At present, the requirement to locate refuge alternatives within 305 m (1,000 ft) of working faces makes BIP RAs impractical in most coal mines. BIP RAs would be practical if three issues are addressed: (1) allowing BIP RAs to be located at greater distances from the working face, (2) developing a reliable process for the design and approval of BIP RA stoppings that meet the 0.1-MPa (15-psi) design criteria, and (3) developing systems that reliably deliver breathable air to the refuge alternative. In 2015, NIOSH OMSHR conducted a study of these three issues and issued a report. In the report, justification was provided for allowing the placement of BIP RAs at greater distances from the working face than the currently mandated 305 m (1,000 ft), guidelines were developed that could be used by industry when submitting BIP RA stopping design applications for approval which are patterned after the Mine Safety and Health Administration guidelines for coal mine seal design applications, and insights were provided into options for providing a reliable supply of clean, breathable air to BIP RAs. This paper presents a summary of the study’s findings and also addresses issues discovered during the building and designing of a BIP RA that OMSHR researchers constructed in NIOSH’s Experimental Coal Mine in Pittsburgh to research the testing and improving of BIP RAs. These issues include several issues related to the delivery, distribution and exhaust of ventilation air to the BIP RA and some general construction issues that require further investigation.

Jan 1, 2016

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022