Search Documents

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17' cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.

By William R. Yernberg

The combined 78th Annual Minnesota Section of SME Meeting and 66th Annual University of Minnesota Mining Symposium was held April 19 and 20, 2005, in Duluth, MN. More than 300 mining professionals, including engineers, executives, mining managers and suppliers, from throughout the United States and eastern Canada attended the meeting. This year’s theme was “Global Demand: A Window of Opportunity.” The meeting included a keynote address, technical presentations and a trade show. The atmosphere at this year’s meeting was upbeat. The iron ore mining industry in Minnesota is experiencing one of its biggest turnarounds in history. Because of greater demand, iron ore prices increased 20 percent during 2004 and 71.5 percent so far in 2005.

Jan 1, 2005

The state of the tunneling and underground construction industry and the advancements of the industry?s biggest machines were the main topics at the 2008 edition of the UCA of SME?s annual George A. Fox Conference. This year SME hosted more than 250 tunneling and under-ground construction professionals at the Graduate Center, City University of New York. During the morning session of the long-running one-day conference, attendees heard a state of the industry through the annual Home-town Update where it was evident that the industry is doing well. Michael McHugh of Moretrench cruised through the many projects that are under way along the Eastern seaboard of the United States and said he could have gone longer if time allowed. An example of how well things are going for the industry is a look at New York, where the industry is flourishing. The New York City Water Tunnel # 3 project is a $668 million project that was awarded to Schiavone/Shea/Frontier Kemper joint venture in 2004. McHugh said that mining on the project was completed in August 2006 and that all con-tract work is expected to be completed by August 2009. The Second Ave. Subway is a $337-million twin tunnel project that will connect upper Manhattan with the financial district. This is a four-phase project. McHugh said the Metropolitan Transit Authority obtained full funding in 2007 and construction awards will be awarded during the next two years. The No. 7 Line Flushing extension, a five-year, $1.15- billion project that will redevelop the Hudson Yards area of Midtown West and the New York City Water Tunnel No. 3 project is the largest capital construction project in New York City?s history. McHugh said the project was given notice to proceed on Dec. 13, 2007. The project includes three large shafts, two parallel 6.7 m (22 ft) tunnels at 2,000 liner m (6,500 liner ft), one large cross adit, one large underground rock cavern station with two interlocks and eight penetrations. These were just a few of projects mentioned in the Hometown Projects update.

Jan 1, 2008

By M. K. Eryadin, I. Yildirim, R. Asmatulu

Novel dewatering aids were tested on various coal samples from the U.S. and Canada in laboratory and pilot-scale filtration experiments. The reagents substantially improved the dewatering kinetics and reduced the cake moistures. The cake moistures were typically reduced from 20-30% by weight to 8-14% range in vacuum filtration. When the reagents were used in conjunction with a pressure filter, higher degrees of moisture reductions were achieved. In the present work, the novel dewatering aids were tested using different types of pilot-scale vacuum filters. The results were consistent with those obtained in laboratory experiments.

Jan 1, 2003

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By J. A. Mielczarski

Surface properties of minerals could be modified selectively and very specifically by adsorption -desorption (dissolution) processes. This requires a monitoring and control of the outermost surface layer at a molecular and atomic level. The nature and structure of self-assembled submonolayers and monolayers at the interface of minerals were studied by infrared reflection spectroscopy. The external reflection spectra of the adsorbed monolayers on any type of minerals: transparent, opaque or non-transparent, recorded at different angles of incidence and for two polarizations are an excellent source of information about the nature and surface distribution of the adsorbed species. The developed method allows to obtain detailed information at a molecular level about the adsorbed surface species. By combination of the simulated and experimental data, the qualitative description of the adsorbed species as well as quantitative evaluation of orientation and the thickness of the adsorption layers were obtained. This fundamental knowledge allows to determine the mechanisms of surface phenomena which govern selective separations. Examples of different surfactant - mineral systems and industrial applications will be discussed.

Jan 1, 2000

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Gary Tomaino, Specialty Minerals Inc., is the chair of the SME industrial minerals technical committees. Technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals as well as sorbents, filter and process aids. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •William Langer, U.S. Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2003

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By R. Mier

The metals and minerals mining industry has evolved dramatically from the earliest objects ever made out of native copper circa 9,000 BC to the modern developments we see today. To better appreciate past developments and to get a sense of where the industry is heading, a brief overview of mayor industry highlights over the last 100 years will be presented, followed by a discussion on potential global scenarios and by a review on mayor industry trends.

Feb 27, 2013