Search Documents

By Randal J. Barnes

A system, such as a mine production system or a mine ventilation system which includes the movement of commodities or some material between decision points may, in many instances, be effectively modelled as a network. Mining has often been characterized as primarily a materials handling function. To a great extent this is true, even though it is an over simplification of all the activities involved in a mining operation. Accepting the materials handling characterization of a mining operation permits the extension of the characterization to a flow process. That is, the ore flows from the mining face through the mining phase (excavation & loading, hauling, dumping) through the milling phase (crushing, grinding, recovery) through the smelter phase and finally to marketing. With this concept it is possible to depict a mining operation as a simple network. For example consider an operation consisting of two mines (A and B) with mills at each mine (MA and MB) with the possibility open to treat ore from mine b at mill NB, but it is not feasible to treat mine B ore at MA. The product of both mills is sold.

Jan 1, 1983

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By James O. Glanville

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal, prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. The literature relating to this process has been reviewed as has the literature relating to the chemical treatment of coal and mineral particulates. Some important articles are discussed and speculations are made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1980

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By Gerry Norton

The overall economics of a coal production unit are governed by a number of interdependent parameters which individually and collectively affect the final result. A business judgement is measured through return on investment considerations and in this respect, a sensitivity analysis proves useful. Figures 1 and 2 show how the various parameters affect return on investment through unfavourable change from planned or expected values. In the case of metallurgical coals, the selling price negotiated is the primary and most sensitive variable, followed by transportation, clean coal yield and capital funds invested in mining. It is clear that coal preparation plant capital and operating costs are the least sensitive to R.O.I. For energy coals, the selling price is determined by heat energy content (x cents per million BTU's) and is therefore not con¬sidered as an interdependent variable. In this case, transportation cost is the major primary factor affecting the level of income. Again the amount of saleable clean coal or total yield has a major effect on return on investment. Most of the factors considered in Figures 1 and 2 are fixed and unfavorable change from planned values becomes critical but clean coal yield is to a great extent controllable during actual operations. Once the theoretical yield for a particular coal has been determined, the optimum return is achieved by approaching this theoretical yield as nearly as possible in practical commercial operation.

Jan 1, 1975

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By George J. Skoronski

The economics of pellet plant operation, in terms of fuel and power consumption, flexibility in the selection of the cheapest fuel source, system availability, maintenance costs, and the simplicity of process design, contribute to the determination of building and profitably operating a pellet plant. Design innovations, sup- ported by actual field data, have been initiated into the GRATE-KILN System design to positively address these factors. This paper presents the recent state of the art design concepts which have helped the GRATE- KILN System assume worldwide acceptance status.

Jan 1, 1983

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By Stanley N. Watowich

Recently the petroleum market has made us aware that we are indeed global natural resource consumers, and as such, we have become captive to fundamental global resource economics and their attendant vagaries. Global resource supply problems are as old as civilization and mineral exploration one of its important catalysts. On the basis of natural resources empires have been expanded and new frontiers have been developed. Global consumption and production might even be viewed idealistically as a system dedicated to optimizing distribution to the consumer. However, this is not the case. Political instability and increased government polarization make dependency on a global market somewhat insecure. The U.S. must evaluate its domestic mineral re- sources on the basis that all metals are critical and that dependency on even the common and base metals may ultimately weaken our domestic economy and our potential international relationships and could cause critical weaknesses as demonstrated by the petroleum problem. This paper evaluates specifically the Duluth Gabbro Complex, of Northeastern Minnesota, (figure l), as a potential resource of critical and strategic metals. First, a chronology of some of the early exploration, will be followed by more recent intensive company studies and preliminary evaluations of economic feasibility. Lastly, metallurgical data, on some optimum conceptual mining plans will allow metal production data to be compared with an estimate of U.S. domestic needs in 1990. The purpose of this paper is to put into focus the difficulty of converting resources into vitally needed reserves.

Jan 1, 1981

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By Alan C. Noble

Ore reserve estimation is a multi- disciplinary process involving not only tonnage and grade estimation (resource estimation), but also consideration of technical and legal aspects such as mining the deposit, beneficiating the ores, and selling the product. This paper provides a background to under- standing resource estimation including geologic modelling, manual estimation methods, conventional computer methods. and geostatistical methods. Mine planning, metallurgical studies, legal/environmental, and marketing considerations are also discussed as they relate to estimating ore reserves.

Jan 1, 1991

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984