Search Documents

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

By R. L. Amelunxen

P. T. Freeport Indonesia (PI) in conjunction with Crescent Technology Inc. has developed a method to predict the metallurgical performance of ores blends based on the behavior of their component ores. The question addressed in this paper is whether ores treated individually could be extrapolated to predict the behavior of a blend of ores. The work further investigates the use of modal analysis to establish individual mineral flotation kinetics in each of the ore zones. This information would lead to the prediction of grade-recovery curves of ores made up of those minerals. Nine samples of ore, representing various zones of FI's Grasberg ore deposit were tested metallurgically and examined microscopically. The same testwork was performed on blends depicting the 1994 mill quarterly feed. Flotation kinetics of the individual ores were then "mathematically" blended and compared to the results obtained from the quarterlies. The calculated kinetics of the actual blends of ore received by the mill were fed to the simulation program and compared to the actual mill performance.

Jan 1, 1995

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984

By Shinzaburo Kato

In 1977 Kawasaki Steel Corporation (KSC) built No. 6 BF (Blast Furnace) with an inner volume of 4 500m3 as part of our program to produce 8.5 million tons of crude steel a year at Chiba Works. As the primary raw material to be used in No. 6 BF, we decided to use sintered ore, because we were confident in the obvious advantages of our technology developed by that time on sintering and BF operation using sintered ore. At Chiba Works, however, we had no space for the construction of a sinter plant, so we decided to build it abroad. Sintered ore is easily crushed and degradated. Producing sintered ore at a point far away from the blast furnace and transporting it across the ocean was the world's first attempt. To successfully realize it, we conducted a series of fundamental surveys and studies with special stress on the real aspects of degradation of sintered ore caused by long-distance transportation and handling and the ways and means to prevent the degradation. As a result, we decided to build a plant on the Mindanao of the Philippines.

Jan 1, 1982

By G. E. Erdman

The total attitude of the industrial minerals producing company is a most important factor in how they regard quality control, technical support for their customers, and procedures used in mining their minerals products. This philosophy of the producing organization directs their action along certain courses. For instance, one producer might see itself as a mining company with its major goal mining efficiency to make it exceedingly price competitive in the market place. Another producer might see itself as a wide spectrum multi-mineral producer that furnishes a reputation for a complete line of products. Another producer might see itself as a specialist in one specific industrial mineral and bet its whole bankroll on providing the very best of quality with the goal of becoming the largest producer of the mineral commodity. Each perception can have a different impact upon the producer's operations and its regard for quality control. Minerals Being Produced The specific markets being served will have their own influence on how mineral product quality is regarded. Ceramic raw materials, for instance, have a very low tolerance for iron which is the cause of low fired color. Thus, industrial minerals for use in glass and ceramic markets must be won from deposits with a very low iron content. A high iron silica sand might be sold to a manufacturer of good old beer bottles. That is a solution to one particular quality facet, but eliminates selling to a significant market in clear glass, porcelain enamel, ceramics whiteware bodies and hobby glazes. Thus, there is a need for sound research in the industries expected to be served before the product is brought to market.

Jan 1, 1987

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By T. Dunn

FMC Corporation has achieved a significant cost reduction through a new proprietary solution mining and processing technology at its Green River, Wyoming Soda Ash Facility. In the first phase, completed in October 1995, trona ore is dissolved, recovered and processed with the new technology, and then fed into an existing refining plant, replacing dry mined and calcined trona ore. The second phase, completed in April 1996, produced a fmal high purity product and increased capacity by 635,000 t/a (700,000 tpy). Both phases were completed under budget and well ahead of schedule.

Jan 1, 1998

By Molood Saeedi, Nima Sadeghi, Eskandar Keshavarz Alamdari

This study showed the kinetics of gold chlorination leaching from an anode slime complex containing copper, silver, barium, selenium, and tellurium. AgCl and BaSO4 control the rate of gold leaching, and the interface transfer and diffusion across the product was selected as the desirable kinetic model. The concentration of hydrochloric acid, chlorine gas flow rate, pulp density, and temperature have been precisely studied. The results showed that temperature and hydrochloric acid have a favorable influence on the leaching rate. However, the chlorine gas flow rate is inactive in the reaction rate. Furthermore, the leaching rate decreased with an increasing pulp density. The leaching process was controlled by the interface transfer and diffusion across the product, and the activation energy was determined to be 13.66 kJ mol–1.

Oct 19, 2021