Search Documents

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By Drummond Earley III

The hydrology of in situ leach mining operations is being studied by the U.S. Bureau of Mines using a variety of techniques, and the Bureau has made significant advances in tracking and modeling the flow of leach solutions in rock formations. However, the influence that leach solution composition has on the hydrology of these systems is poorly understood, and geochemically-controlled changes in the hydrologic characteristic of ore deposits during in situ leach mining of porphyry-hosted, copper oxide ores have not been previously studied. The Cyprus Casa Grande in situ leach mining operation mines fracture-hosted and disseminated copper oxides (predominantly chrysocolla) hosted by granodiorite porphyry using a pattern of underground wells. The injection solution consists of sulfuric acid raffinate from a solvent extraction-electrowinning plant. Chemical analysis of representative injection and recovery solutions reveals that gangue cation concentrations in these solutions are high, and geochemical modeling shows that the solutions are saturated or nearly saturated with respect to gypsum, jarosite, and various amorphous oxides. Precipitation of these solids is evoked by calcium-exchange reactions, rising pH, and perhaps locally rising redox potential, as the leach solution reacts with the ore minerals, host rocks, and the atmosphere. Mass and volume balance calculations show that approximately 25 cm of precipitates are formed per gram of copper recovered at Cyprus Casa Grande. The results of geochemical modeling agree with petrologic examination of pre-and post-leach core samples from the leached horizon. Moreover, hydrochemical modeling and hydrologic field data suggests that chemical precipitation causes significant decreases in porosity and permeability during in situ leach mining of porphyry-hosted, copper oxide ore.

Jan 1, 1992

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By Hongsheng He, Xiaofang Lv, Jianfeng Wang

This paper provided an overview of characteristics of limonite ores as well as their influence on sintering performance. Evaluation experiments focusing on basic characteristics, granulation characteristics, and high temperature sintering characteristics had been conducted by using two types of limonite ores, then the principles of high effective utilization technology of limonite ores were discussed, and the sintering pot tests were conducted. Limonite ores possessed low total iron content, high combined water content, high SiO2 content, large average particle size, low adhering particles proportion, high porosity, high water absorption rate, short water absorbing time, poor granulation ability, high melt formation ability, low melt fluidity ability, low melt penetration ability, high melt absorption ability, low bonding phase strength, and high forming ability of SFCA. By taking the technical measures of ore-proportioning optimization, increasing the proportion of burntlime and segmentation granulation, the usage of limonite ores could reach 50% in sintering.

Aug 27, 2021

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By Christos Roumpos, Philip‑Mark Spanidis, Francis Pavloudakis

Coal mining operations are large-scale, long-term frameworks of high complexity. Mining organizations accumulate, develop, and leverage knowledge from diverse scientific and technological fields as a result of these operations. Both practical experience and existing literature indicate that knowledge management (KM) methods within the mining industry primarily target solving immediate technical challenges and operational requirements. However, they are not commonly regarded as strategic tools to enhance the performance and competitiveness of mining companies. Empirical evidence from the Greek mining industry suggests that the management of available knowledge is intricate, less effective, and dysfunctional. This paper presents a methodology based on the principles of quantitative research (QNR), collaboratively conducted with a group of mining experts, to assess the KM landscape in the Greek mining industry. The methodology involves a structured data collection framework using questionnaires, subsequent statistical analysis, a discussion on critical methodological aspects, and an interpretation of results focusing on key aspects useful for planners and designers of KM systems in the mining industry. Finally, the paper concludes by summarizing the methodology’s outcomes and proposing further perspectives for research.

Mar 16, 2024

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By H. B. Miller

Contract Incentives have long been employed in the underground hardrock industry as a tool to influence employee performance, enhance productivity, and control labor costs. While traditionally structured to establish a direct correlation between performance and compensation, many contract programs have evolved into elaborate systems that promote strategies often viewed as independent of productivity. This paper presents the findings of research into these contract incentives and was conducted with the cooperation of 33 mines utilizing a spectrum of employee compensation and incentive programs. Emphasis of this analysis focuses on the types of production contracts observed and their role with respect to employee earnings.

Jan 1, 1994

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983