Search Documents

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

Froth flotation processes are carried out in flotation cells that are grouped into banks, and these banks are interconnected, forming a flotation circuit. A literature review shows the existence of papers related to flotation circuit design based on mathematical programming. However, due to the complexity of solving the mathematical model in most of the work, it is considered that a small number of species is present in the feed to the circuit, which differs from practice. In addition, simple bank models are generally used. This paper presents a methodology for designing mineral concentration circuits that overcomes the problems mentioned. It allows the use of more suitable cell or bank models and the inclusion of several species. The methodology is based on two phases. The first phase identifies the set of optimal structures using discrete values of stage recoveries, solving several mixed integer linear programming (MILP) problems. In the second phase, the optimal design for each of the structures obtained in the previous phase is determined using a suitable model for the recovery at each cell or bank, which results in a mixed integer nonlinear programming (MINLP) model. The design of a copper concentration plant with eight species and the design of a zinc concentration plant with three species and five size fractions by species are used to validate the proposed methodology. The structure of the cells in the rougher and cleaner banks deliver structures that are novel.

By John A. Folinsbee

Placer Dome Canada owns and operates the Campbell mine and mill at Balmertown, in the north western corner of Ontario. The mine operates at 1.3 kt/d (1,500 stpd). It produced more than 9.3 t/a (300,000 oz/year) of gold during the last three years. Changes to the gravity concentration circuit have resulted in a 10% to 15% increase in gravity recovery. The mill head grade at the Campbell Mill is relatively high, averaging 18.5 g/t (0.54 oz/st) over the total reserve tonnage. During the past several years, the head grade was averaging close to 20 g/t (0.6 oz/st). Before 1994, gravity concentration was achieved by using a combination of conventional mineral jigs and tables. Jig concentrates were upgraded on shaking tables to produce a concentrate, which was refined to bullion. In May 1994, management decided to buy two Knelson CD 760-mm (30-in.) concentrators. The objective was to replace the existing jigs and increase gravity gold recovery by up to 15%. Gravity recovery with jigs averaged between 30% to 35%. Gravity recovery was anticipated to increase to about 50% with the Knelsons.

Jan 1, 1997

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026

By Zhongwei Wang, Dong Wang, Feng Ju

The coal seam in the southern coal field of the Ordos Basin serves as the main aquifer, while the region is known for its high-intensity coal mining activities. The coupling effect of mine water and the strong disturbance caused by high-intensity mining have brought serious challenges to the stability of coal pillars. To address this, a formula for determining the reasonable width of coal pillars under the aforementioned coupling effect and establish a criterion for coal pillar instability in this paper. A case study was on the 11,215 working face at the Xiaojihan coal mine in the area to investigate coal pillar stability. Results indicate that the strength and stability of the coal pillar are affected by the water content, with a small water content increasing its strength and large water content weakening it. In high-intensity exploration of watery coal seams, the best stability of the coal pillar is achieved at optimal water content and mining rates. For the Xiaojihan coal mine, the optimum water content and mining rate are 3.31% and 20 m/d, respectively, ensuring the efficient mining of watery coal seams. Furthermore, this study's findings can provide valuable references for the mining design of coal mines with similar geological conditions in the region.

Feb 13, 2024

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By T. Umadevi, A. Pratap Singh, R. Sah, K. Abhishek

"It was possible to beneficiate a low-grade iron ore fines sample from Bellary-Hospet, Karnataka, India assaying 56% Fe, 9.1% SiO2 and 5.2% Al2O3 and produce two concentrates, namely, a sinter-grade fines concentrate (43.7% by weight), assaying 63.6% Fe, 2.6% SiO2 and 1.7% Al2O3, and a pellet-grade concentrate (30.7% by weight) assaying 64.7% Fe, 2.9% SiO2 and 1.7%Al2O3. Rejects (25.6% by weight) assayed 32.5% Fe, 27.9% SiO2 and 15.4% Al2O3. The mineralogical characterization indicated that the sample consisted of 69.5% ironbearing minerals (56% hematite, 7.5% martite and 6% goethite-limonite), 12.5% quartz and 15.2% clay, and the rest were minor minerals. Liberation size was found to be in the size range of 25 to 100 µm. The process flow sheet consists of jigs, spirals, grinding and low- and high-intensity magnetic separation of the deslimed feed. IntroductionJSW Steel Ltd is a 10-Mt/a integrated steel plant. To produce 10 Mt/a hot metal requires nearly 16 to 20 Mt/a iron ore fines. The fast depletion of highgrade iron ore fines, increased industrial demand and an increase in iron ore prices have necessitated the exploitation and use of low-grade iron ore fines in the steel-making process after beneficiation. Thus, the beneficiation of low-grade iron ores by removing the associated gangue minerals and enhancing their grade is essential. The use of these iron ore fines in sinter and pellet making has prompted the undertaking of systematic studies on low-grade iron ores.Finely disseminated low-grade iron ores with siliceous impurities have been upgraded by gravity, magnetic and flotation-based processes (Burt, 1994; Svoboda, 1987; Houot, 1983). The processing of low-grade Indian hematite ore containing high levels of alumina-bearing minerals as impurities present separation challenges and pose special problems in martite and magnetite, in association with quartz and clay as the gangue-forming minerals. Alumina is mainly contributed by clay (kaolinite, montmorillonite, illite, alunite), lateritic material and gibbsite; some alumina occurs as solids in iron oxide minerals, namely, goethite and limonite. Silica is mainly contributed by quartz and the associated clay. achieving a high-grade concentrate (Pradip, 1994; Singh and Mehrotra, 2007). Hematite ore basically consists of varying amounts of hematite, goethite,"

Jan 1, 2015

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By A. Sinha, C. Sawmliana, P. Pal Roy

Using the newly developed and permitted explosive Pentadyne-HP (Gulf Oil Corporation Ltd., Hyderabad), the Blasting Department of the Central Institute of Mining and Fuel Research, Dhanbad experimented at the GDK-5 Incline, RG-1 Area of the Singareni Collieries Company Ltd. (SCCL) to establish one modified angular cut blasting pattern as an alternative to conventional solid blasting in India to obtain longer pull, as well as to achieve at least 40 t of coal in a single blast round for the deployment of diesel load-haul-dump units at the face. This permitted explosive satisfied the statutory requirements of incendivity characteristics applicable to P5 explosives of the regulatory agency Directorate General of Mines Safety (DGMS) of India. The present paper summarizes the development of this new blasting pattern and its possible use in Indian coal mines.

Jan 1, 2010

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977

By K. V. Raj, T. Bhowmick

"Control of fugitive dust in high latitude open-pit mines is challenging due to unique atmospheric phenomenon resulting in complicated flow regimes, and atmospheric inversion due to lack of adequate solar insolation during prolonged winter seasons. In this study, two idealized (One conical and one trapezoidal) three-dimensional open-pit mine geometries are simulated for differing seasonal conditions using the CRADLE-CFD package. The airflow is modeled using Standard Kappa-Epsilon Turbulence Model solved by RANS equations. The concept of particle tracking is used to predict the flow pattern of dust particles. For various climatic conditions, and two different pit geometries, fugitive dust particles varying in size (PM0.1 to PM10) and concentration are generated at various locations of a mine and dispersed by the airflow pattern inside the open-pit mine. The amount and location of dust particles inside the pit is reported at various time intervals. The development of atmospheric inversion during the winter season significantly affected the amount of dust retention inside the open-pit domain. While during the summer, airborne dust particles were transported outside the open-pit domain in a short time. INTRODUCTIONComputational fluid dynamics (CFD) modeling of open-pit mines is challenging. In a recent paper, Bhowmick et. al. [1] presented different constraints and challenges in developing a 3-Dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. Simulation results of a 3D non-hydrostatic model by Shi et al. [2] showed that both the mechanical and thermal forcing are important mechanisms, controlling the development of the atmosphere inside an open-pit. Alvarez et al [3] used a CFD model for predicting dust dispersions in a medium sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al [4] introduced a more sophisticated parameterization of the dust sources. Flores et al. [5] used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual open-pit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (i) air advection (10 m/s) driven mechanical turbulence; (ii) surface heat flux (240 W/m2) driven thermal buoyancy; and (iii) both air advection and surface heat flux driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (non-buoyant case)"

Jan 1, 2015

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By Rihab Guellala

In Tunisia, the Paleocene-Eocene series has an important socio-economic interest. It contains profitable oil and water accumulations. Moreover, it encompasses phosphate reserves. The present study uses seismic reflection prospection and borehole data for the reconstitution of the Paleocene-Eocene deposit structure in the Jerid area (southwestern Tunisia), a crucial step for the phosphate exploitation. Firstly, lithostratigraphic correlations incorporating water and petroleum wells were established according to different directions for a tentative approximation of the Paleocene- Eocene deposit geometry by following their lateral evolution. To give more details, seismic reflection profiles were interpreted in the second step. The Paleocene-Eocene formations were associated with their corresponding reflectors on the closest seismic profile using the relation of time and depth in petroleum wells. Analysis of lithostratigraphic correlations shows notable variations in the Paleocene-Eocene series thickness and depth. Seismic profile interpretation explains these variations by highlighting different buried tectonic features. The results confrontation reveals that the phosphatic deposit geometry in the Jerid area is mainly influenced by the (1) emergence of the Saharan platform and the Chott northern chain since the Late Cretaceous, (2) syn-sedimentary normal activity of E-W and NE-SW faults during the Paleocene-Eocene epoch, (3) reverse-reactivation of these faults, and (4) major Tortonian folding phase. This study can enormously enhance the Jerid area socio-economic development by presenting useful findings that may orientate the phosphate exploration.

Aug 15, 2021

By Stanley M. Jarrett

Gentlemen, I am pleased to address this gathering of engineers and operation managers representing a large and important segment of the metal and nonmetallic mining industry. Since you know from the printed program that the theme of my paper is the furthering of safety in open pit mines, perhaps you will have guessed that I will also comment upon the image created in the public mind by the industry's safety record and the potential consequences thereof in national health and safety legislation. Operators of surface mines have some cause to congratulate themselves on the basis of figures issued by the national safety council which show that lost-time accidents per-million-man-hours in surface mining (11.18), is lower than that of all other mining. Moreover, the accident frequency in surface mining is only slightly above the median accident rate for all American industry (8.87). That is a good record.

Jan 1, 1972

By MUSTAFA ERKAYAOGLU, Muhammet Mustafa Kahraman

Particulate matter (PM) is one of the main actors related to air pollution caused by surface mining. Fugitive dust, considered as particulate matter that cannot be collected by conventional measures, is classified by the particle size. The Environmental Protection Agency (EPA) categorizes PM as coarse and fine particles based on the particle size being less than 10 μm (PM10) and less than 2.5 μm (PM2.5). Basic operations of surface mining such as drilling and blasting, loading, haulage, and processing are processes that can potentially generate fugitive dust. Regulations and legislations enforce the mining industry to use environmental monitoring systems, fugitive dust level measured by PM10 level as part of this. Air quality monitors are positioned at different locations around surface coal mines and track air quality levels during production. This study introduces a data-driven methodology to handle air quality issues related to fugitive dust at surface coal mines. Data is sourced from different mine equipment in real-time and they are integrated with air quality monitoring systems to provide information to support decisions for fugitive dust. The method is implemented and demonstrated in a case study at a large surface coal mine.

Sep 29, 2020