Search Documents

By K. H. Nimerick

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.SoC (O°F). Other areas where FCA has found utility has been de-icing conveyor belts, idler, idler arms and other moving parts that have been impeded by ice.

Jan 1, 1977

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By B. Whisner, A. Smith, J. Carr

"Electromagnetic based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine. INTRODUCTION Electromagnetic based proximity detection systems have been developed to reduce machine-related accidents in underground coal mines. The first proximity detection systems installed in underground coal mines were developed for continuous mining machines (CMMs). There are five of such proximity detection systems that are approved for use in U.S. mines by the Mine Safety and Health Administration (MSHA) (Mine Safety and Health Administration, 2013; Mine Safety and Health Administration, 2015). There are several basic components that interact within an electromagnetic proximity detection system (PDS). A PDS includes two main elements: a set of generators to create magnetic fields around a CMM and a set of magnetic probes to detect the fields. These systems can determine if a miner is located at a safe distance from the machine based on the detected magnetic flux density. Stability of the magnetic fields is essential for system accuracy."

Jan 1, 2018

By Francis Martino

Just as coal producing mines are faced with various handicaps which control the quantity of coal produced and sold, the subsequent user of that product is faced with parameters that impact the optimum utilization of coal. Traditionally, the industry focused on the quantity of mineable coal in a reserve. The mine planning development was primarily concerned with two important criteria: (1) safety and (2) the productive efficiency in a quest to produce the lowest cost coal.

Jan 1, 1982

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By N. A. Sareyed-Dim

Nickel ores may be classified into two major categories : sulphide ores, and oxidized lateritic ores, these latter containing nearly 80% of the known reserves of the metal (1). Two types of lateritic ores are recognized; ores high in iron but low in magnesia and silica are known as "limonitic", while ores low in iron but containing high percentages of magnesia and silica are called "silicate" (see Table I). Sulphide ores can be beneficiated readily by conventional ore dressing techniques and the technology for nickel recovery from such ores has been well tested in a number of commercial processes (1-4). Unfortunately, no economically viable process for the concentration of nickel from low-grade deposits has yet been developed, and so only the high grade ores are able to be worked profitably. Silicate ores have been treated pyrometallurgically for the production of ferronickel (2) (3) (5); limonitic ores have been processed hydrometallurgically to produce nickel metal (2) (3) (6) (7).

Jan 1, 1975

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By David S. Cahn

For many years the green and dry compressive strengths' of pellets have been, considered as possible criteria of pellet performance during induration. Although widely quoted throughout the industry, little attention has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of the test. The purpose-of this study was to compare the constant deformation rate test with that using a constant loading rate in addition, the dependence of these tests on such pellet properties as size, weight, and method of balling was to be investigated.

Jan 1, 1967

By C. Okrusch, C. Roos, M. Akers, S. Rosenthal

Modern mining consistently faces controversy. Public sentiment impacts the permitting and development of mines, so a quality public relations (PR) program for mining companies may improve society’s impression of the mining industry. Developing mines face more permitting challenges than operating mines, which stems from a lack of societal trust given the history of mining and its impact on the environment. Two case studies were selected based on the type of public controversy they face to demonstrate how pervasive permitting issues are in industry. Both Pebble Mine, owned by Northern Dynasty Minerals (NDM), and Black Butte, owned by Sandfire Resources America Inc (SRA), experienced difficulties with their water permitting due to potential risks their mine developments posed to local fish populations. Pebble has, to date, failed in all of their attempts to become permitted due to concern for the water and the fish. Black Butte dealt with the same problems, on a smaller scale, but was able to become permitted. These two mines will be discussed in detail including local history, mine setting, mining history in America, prevalent culture groups, technology development, and intercultural communication competence (ICC). The mining industry needs to evaluate its ICC skills since ICC directly determines the effectiveness of PR. Based on Barna’s Stumbling Blocks for intercultural communication, methods for improving the mining industry’s PR will be suggested in the hope of easing the permitting process for future mines by developing ICC.

Mar 2, 2022

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the cost approach category for real property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties. The author reasons that standards and regulations pertaining to real property valuation should be modified, and underlying principles should be expanded, so as not to inhibit appropriate application of these cost approach methods.

Jan 1, 2011

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers' opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990