Search Documents

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By L. E. Eary

Many of the major international gold mining companies provide data on rates of greenhouse gas (GHG) emissions as part of their environmental reporting commitments. These data are evaluated by an index defined as the annual GHG emission rate in metric tons, divided by the annual amount of gold produced in grams, and referred to as GHGgold. This paper examines ranges of GHGgold values for a cross section of gold mines as a function of mining method (openpit, underground and combined operation) and ore-processing method (mill, heap leach and combined methods) for reported ranges of operational data, including annual total tons mined, ore processed and gold grade. The evaluation shows that ranges and distributions of rates of GHG emission are approximately similar across different mining methods and ore-processing methods. The data presented in this paper provide the context needed to make comparisons of GHG emissions reported in companies’ annual reports to the ranges reported for the overall gold mining industry.

Jan 1, 2009

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By Ben W. Burdett

Since the late 19701s, the use of microcomputers in the minerals industry has grown to the point where today they can be found in virtually every plant within the industry. Their use in every aspect of instrumentation and control has increased the ease of operation and control of every phase of mineral processing. Their incorporation in sensors, transmitters, indicators, and controllers in addition to their use in distributed control and computer systems has provided operators with more timely accurate information than they have ever had before. This has led to an increase in the operator's effectiveness and an improvement in overall productivity. The ultimate aim of plant control is to maximize recovery in the mineral processing operation, and the microcomputer has spawned many tools that are now making this goal attainable. This paper discusses individual use of microcomputers in the areas previously mentioned as well as their collective use in overall control systems. The incorporation of local control systems in total plant control including the communication of information throughout all levels of plant management is also discussed. Finally the role the microcomputer is playing in today's plants is illustrated with numerous references to current examples.

Jan 1, 1985

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By M. E. Grimes

The Port Radium mine of Eldorado Mining and Refining Limited, located on Great Bear Lake only a few miles from the Arctic Circle in north-western Canada, is the oldest uranium producer in Canada, The first concentrates were produced in 1933 and except for a period between 1940 and 1942 the mill has operated continuously. Although it is located in a remote area, and compared to more recent mines in other areas is a small tonnage operation, nonetheless the relatively high grade of the Port Radium ore has permitted operation to date on an economical basis. The mill process at Port Radium includes the original gravity concentration mill, and since 1952 an acid leaching plant which treats tailings from the gravity mill and tailings recovered by dredging of residues from underwater dumps in Great Bear Lake. The pregnant solution from the leach plant has to date been processed through aluminum reduction to yield an intermediate grade uranous phosphate-arsenate precipitate, Because of the rising costs of the aluminum reduction process, and its sensitivity to ore composition, Eldorado became interested in possible application to Port Radium of the solvent extraction processes of which we were obtaining increasing information in the latter part of 1954 and during 1955.

Jan 1, 1958

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By B. Qiu, Y. Luo

The design of the predriven recovery room is not an easy task, because the stress distribution in the barrier pillar, standing supports, fender pillar and the immediate roof is changing as the longwall face approaches the predriven recovery room. An analytical approach is proposed to determine the stress distribution in the barrier pillars, fender pillars, standing supports and immediate roof of the recovery room based on the fracture mechanics approach. Based on the developed mathematical model, a stand-alone computer program has been developed to facilitate the required computations. The parameters such as overburden depth, recovery room width, mining height, shield and standing support capacities are incorporated into this program to access the feasibilities of predriven recovery room designs. Compared to the finite element method previously employed, this analytical approach offers the same, if not better, accuracy without requiring expensive computer hardware and software or specialized expertise.

Jan 1, 2012

By Onur Golbası, Berk Gokce

Investment decisions in the mining industry are complicated by sector-specific uncertainties. This study presents a multi-submodule system dynamics model to capture the dynamic complexities of decision-making across mineral property development stages. The model includes five interconnected subsystems: valuation, production, growth strategy, demand, and finance. Developed through system decomposition, expert input, and literature, the model is tested on a hypothetical copper mine with 850 ktpa capacity and 1% cu grade. Simulated over five years with quarterly steps, it estimates an enterprise value of $78.9 million and a target growth rate of 11.2%. Results highlight the significant effects of operating costs, capital policies, and inflation on free cash flow, and the critical role of mineral reserves in sustaining growth. This model supports strategic investment analysis across different minerals and development phases, offering mining investors a robust tool for optimizing decisions.

Feb 22, 2026

By W. C. Morgan

Recently passed federal strip mining legislation officially emphasizes that the increased coal production required by this country through surface mining is going to be obtained only with stricter environmental standards. Dozing overburden down the hillside in Appalachian contour mining or leaving drag1ine spoils in area mining is now taboo and it is now or will soon be necessary to return the disturbed land to as good or better condition than before mining. These new restrictions will create a need for new and better ways to do the job. This paper describes one approach for utilizing scrapers and dozers to strip all of the overburden and to replace that overburden in an environmentally satisfactory fashion. The objective was to do this at a lower cost than that possible with the traditional dragline system using dozers and scrapers for reclamation and topsoil handling. In area stripping, the dragline has been able to move overburden at an extremely low cost. Operating costs of 8-13¢/bcy are typical in many operations where rehandling is not required. However, the cost of leveling the spoil piles and rehandling topsoil add considerably to the low basic cost of drag1ine stripping.

Jan 1, 1977

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By James B. Cathcart

Marine phosphorite deposits occur in Brazil, in the Bambui Group of late Precambrian or Early Cambrian age. The phosphorite is laminated, isoclinally folded, and is composed of black, elongated apatite pellets and quartz grains cemented by quartz and muscovite. Abundant, narrow quartz veinlets cut through the rock at right angles to the elongation direction of the pellets. The phosphorite is 0 to 80 meters thick and contains 5 to 30 percent P205. The deposit is elongate towards the northeast, and the central, thickest, and richest part is bounded by faults. Measured reserves are about 250 million tonnes that average about 13 percent P205. Preliminary testing indicates that grinding, scrubbing, and desliming will produce a material usable for fertilizer manufacture at a cost competitive with imported phosphate fertilizers.

Jan 1, 1977

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver&apos;s experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985