Search Documents

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By Peter Jackson

Over a quarter of a century ago a New Zealand physicist suggested the possibility of detecting coal seam discontinuities by a seismic method carried out underground in the mine workings (Evison 1955). Twenty years ago initial experiments were performed in Germany (Krey 1963). Since then research has continued, notably in Britain and Germany, in order to provide a reliable fault and washout detection system. The National Coal Board of Great Britain has now carried out more than 250 surveys in Britain, France and Australia. The first NCB survey in the U.S., a successful application of the technique to an Ohio coal seam, will be described and the strengths and limitations of the method explained.

Jan 1, 1984

By O. J. Malacarne

The use of a series of thickeners for-washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The, common, practice is to wash the sand fraction in classifiers and, the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear, Company, a total ore' acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1,000 to 1,300 tons per day in a series of washing thickeners. A typical screen. analysis of the ore being washed in these thickeners, is 25 percent -200 mesh, 3 percent +35 mesh and about, one' percent +l4 mesh., The amount of slimes (-200 mesh) will vary from 20 to 30 percent s the mill receives ore from 150 different mines The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and of course ally acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Company is located in Montrose County, Colorado and is physically located on a canyon wall along the San Miguel river. The thickeners referred to in this, paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north.

Jan 1, 1962

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By S. Perla

Two of Peabody Western Coal Company's mine operations are the focus of this paper ... Black Mesa Mine and Kayenta Mine, both located in Northern Arizona. These two locations are unique for a variety of reasons. ? The two mines have only two customers, both power plants, one the Southern California Edison's Mohave Generating Station near Laughlin, NY, the other the Navajo Generating Station near Page, AZ. Close in proximity, these two locations ships nearly 12 million tons of coal per year. ? Material is shipped to these customers two ways: via a 273 mile underground slurry pipeline, which by the way is longest in the world, and by a 17 mile long conveyor to four storage silos. Product is then shipped via train from the storage silos to the plant sites.

Jan 1, 1995

By K. A. Natarajan, S. Usha Padukone

"An industrial waste liquor having high sulfate concentrations was subjected to biological treatment using the sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans. Toxicity levels of different sulfate, cobalt and nickel concentrations toward growth of the SRB with respect to biological sulfate reduction kinetics was initially established. Optimum sulfate concentration to promote SRB growth amounted to 0.8 - 1 g/L. The strain of D. desulfuricans used in this study initially tolerated up to 4 -5 g/L of sulfate or 50 mg/L of cobalt and nickel, while its tolerance could be further enhanced through adaptation by serial subculturing in the presence of increasing concentrations of sulfate, cobalt and nickel. From the waste liquor, more than 70% of sulfate and 95% of cobalt and nickel could be precipitated as sulfides, using a preadapted strain of D. desulfuricans. Probable mechanisms involving biological sulfide precipitation and metal adsorption onto precipitates and bacterial cells are discussed.IntroductionIndustrial effluents from hydrometallurgical and mineral processing operations often contain high sulfate and metal concentrations posing significant disposal problems, which require urgent solution to avoid serious environmental contamination. In such waste liquors, sulfate and heavy metals such as cobalt, nickel, zinc and iron originate from the chemical or biological oxidation of exposed sulfide minerals. Reduction of sulfate and precipitation of toxic metal ions from industrial wastes is essential from the viewpoint of environmentally acceptable waste disposal and recovery of associated strategic metals.Many of these heavy metals are essential for metabolic activity of bacterial cells at low levels. But they exert toxic effects at concentrations encountered in polluted water. Removal of toxic metals through biological reduction of sulfates from industrial waste waters have been practiced for several decades. Metal remediation through common physicochemical techniques such as oxidation-reduction, chemical precipitation, filtration, electrochemical treatment, evaporation, ion exchange and reverse osmosis processes is expensive and not suitable in the case of voluminous effluents containing complexing organic matter and low metal concentrations. Further, strong and contaminating reagents are used for desorption, resulting in toxic sludge and secondary environmental pollution. Biotechnological approaches can be more efficient and cost effective for detoxification of such effluents. Biotreatment/ bioremoval offers several advantages over conventional chemical and physical treatment technologies, especially for diluted and mixed contaminants. Biological detoxification, which involves the use of microbes to detoxify and degrade environmental contaminants, has received increasing attention in recent years (Iwamoto and Nasu, 2001). In addition, valuable metals can be recovered from metal sulfide sludge (Boonstra et al., 1999)."

Jan 1, 2015

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By J. Zhai, Z. Yin

"The electrokinetic and flotation behaviors of ilmenite using lead ions as the activator and sodium oleate as the collector were studied. The results of microflotation show that the flotability of ilmenite can be improved by lead ions obviously. The isoelectric point of ilmenite increases from 5.32 to 7.7 after the addition of lead ions because of the adsorption of Pb2+ and Pb(OH)+. The results of zeta potential measurements and the collector adsorption density calculation show that the adsorption of sodium oleate on the ilmenite surface via chemisorptions in addition to electrostatic interactions. Besides, the adsorption density calculation results show that as the addition of lead ions as the activator, the adsorption amounts of collector are greater than those without activation which is in aggrement with the flotation behaviors. INTRODUCTION Ilmenite, as an oxide mineral of formula FeTiO3, is usually used as the main resource of the extraction of titanium (Bulatovic and Wyslouzil, 1999). There are many researches showing that the conventional methods, such as gravity separation, magnetic separation and flotation, do not work efficiently as expected (Mehdilo et al., 2015; Zhu et al., 2011). Nowadays, to produce ilmenite concentration feasibly and efficiently, these separation methods above are combined for a reason that the raw ilmenite ores are characteristic of poor, fine and complicated. Moreover, surface modification, such as surface dissolution method, microwave irradiation and oxidation roasting, is applied to improve the flotability of ilmenite currently (Welham and Llewellyn, 1998; Zhang and Ostrovski, 2002). Generally, fatty acid salts are used as the collector for the flotation of oxide minerals and sodium oleate is usually used as the collector for the flotation of imenite ores (Fuerstenau and Pradip, 2005). The mechanism, such as individual ion electrostatic adsorption, chemical adsorption, ion–molecule dimeric complex adsorption, and the coadsorption of ion and molecule, have not been discussed systematically using sodium oleate as the collector in the flotation of ilmenite (Somasundaran, 1983). Under the activation circumstance using the lead ion as the activator and sodium oleate as the collector, the interaction mechanism seems to be still unclear. In the present study, the interaction mechanism between ilmenite and sodium oleate using lead ion as the activator are studied by microflotation, zeta potential measurements and adsorption density calculation. EXPERIMENTAL Materials and reagents Pure ilmenite minerals were obtained from Panzhihua, Sichuan province, China. The minerals were ground in a porcelain mill with an agate ball. Following that, the prosucts were sieved, and the samples of -0.074+0.038 mm size fraction were used for the microflotation experiments. The results of XRF show that the content of titanium element is 30.58%, showing that the purity of ilmenite is above 90%. On the basis of the results of XRF, it is determined that the purity of ilmenite is very high and meets the needs of microflotation"

Jan 1, 2017

By M. Pawlik

Canadian sylvinites contain over 90% of KCl and NaCl and a few percent of water-insoluble minerals. Cationic flotation is used to produce KCl concentrates. Since water-insoluble minerals appear in the pulp as slimes, and since long-chain primary amines are utilized as a collector, desliming is essential. The potash industry utilizes different desliming methods. This may involve selective flocculation of the slimes with polyacrylamide and removal of the flocculated product by flotation, or mechanical desliming with the use of classifying cyclones. Whichever method is applied, desliming is never complete; the flotation feed after desliming still contains about one percent of the slimes which heavily affect collector consumption and flotation selectivity. Therefore, the remaining slimes have to be rendered inactive by “blinding” them with polymers such as carboxymethyl cellulose or guar gum. The commercial blinders used by the potash industry include natural and synthetic polysaccharides. The most common is the use of carboxymethyl cellulose (CMC) and guar gum (GG). These are quite different polymers, while CMC is anionic, GG is non-ionic; while the applied CMCs are of relatively low molecular weight (about 300,000) GGs have much higher molecular weight. Guar gums are also heavily used as the depressants of naturally floatable gangue in the processing of platinum-bearing ores, and according to Harris et al. (1999) quite a large variety of modified guar gums are available in South Africa for this application. Cheng et al. (2002) claim that natural guar gum’s molecular weight is 1.935 • 106. Robinson et al. (1982) found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105. The highest molecular weight sample is then very close to the natural guar gum studied by Cheng et al. (2002). According to the manufacturer, the Rantec KP4000 guar gum which is used by the Canadian potash industry has a molecular weight of about 1.5 x 106. Since both KCl and NaCl are soluble in water, the flotation process is carried out in saturated brine. At 20 oC, 1450 kg of NaCl-KCl-H2O saturated solution contains about 0.300 kg of NaCl, 0.150 kg of KCl, and 1 kg of water (Gaska et al., 1965). Thus, in the saturated NaCl-KCl brine there are about 5.1 kmole of NaCl and 2 kmole KCl per 55.5 kmole of water. This gives 3.9 molecules of water per each ion assuming complete dissociation of NaCl and KCl. Thus, it is obvious that all water molecules in the saturated brine must be bound in the hydration shells around the hydrated ions. The surface tension of the NaCl-KCl saturated brine was recently measured to be 85 mN/m (Laskowski et al., 2003).

Jan 1, 2004

By C. J. Webb

Abandoned uranium mines in the southern Black Hills of South Dakota were sampled for uranium, radium, and rare earth elements during 1992 and 1993. Analyses of water samples from several shallow ponds in the mine pits showed pH values between 3 and 4 with uranium concentrations between 1600 and 2600 ppb. Rare earth elements and their respective isotopes were analyzed with an inductively coupled plasma mass spectrometer and were referenced to a shale normalization pattern. All samples showed an enrichment in the middle rare earth elements. Rare earth levels often were greater than 0.2 ppm. At one site, the concentrations of lanthanides were 150,000 times above background levels. While the southern Black Hills have long been known for rich uranium ore deposits, these analyses show that significant levels of rare earth elements also are present, indicating that the potential exist for future development.

Jan 1, 1995

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By Malte J. M. Gurgel, Axel Preusse

The planning, construction, and monitoring of underground storage facilities is a key factor in meeting upcoming challenges as part of the energy transition from fossil fuels to renewables. Therefore, the many years of knowledge and expertise in ground control gained from coal mining are highly valuable for new mining and storage operations. For such applications, our previous work examined cavity registration, combining structure from motion and LiDAR through a case study in a former lead ore mine. Building on this, the results of this recent case study are discussed regarding the possible application in sites for nuclear waste disposal in Germany including a view on the situation in the United States. Photogrammetric methods are particularly suitable as part of long-term monitoring, which relies on both precise survey results and a large variety of detailed visualization. In order to gain a better understanding of the resulting application potential for holistic monitoring, both existing repositories sites in Germany and ones yet to be found are examined. This search and selection process for high-level nuclear waste disposal is studied in detail together with rules resulting from the (German) mining law, regulations, and other guidelines. Hereby, key requirements of photogrammetric products like oriented images, point clouds, and three-dimensional (3- D) models are identified for different case studies. The findings on accuracy and integrity of the generated models are not only of interest for future repository sites or underground pumped storage power plants, but also offers various possibilities for underground mining of coal and other commodities.

Jul 1, 2023

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970

By V. Voller

A relatively simple model of grinding which incorporates both the Bond grindability equations and the population balance equations has been extended to form a comprehensive simulation package that can describe most kinds of conventional grinding circuits. The package has two programs, with the first consisting of an input program which helps the user to specify the prescribed circuit, while the second program performs the actual simulation. The package serves two main purposes - i) as a check on mill design, with the output providing not only predictions for the product passing size but also of the full product size distribution, and ii) as a means to assess the likely effects on the product size distribution of operating under different sets of conditions.

Jan 1, 1981

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Zoheir Khademian, Morgan Sears

According to the 2010–2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in US longwall mines were caused by roof instability. Gateroads are subjected to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many US longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the bonded block modeling (BBM) of roof by UDEC was validated against field extensometer measurements in a longwall entry roof at a 180-m depth of cover. The BBM was shown capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. Results demonstrate the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 13, 2024