Search Documents

By P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous Chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By Otto Braach, Wolfgang Frietzsche, Erdogan Gürkan

The Westerschelde Tunnel is located in the south of the Netherlands and links the two parts of the Provinces of Zeeland, Zeeuws-Vlaanderen and Zuid-Beveland, which are separated by the Westerschelde. Road traf?c has up till now taken the detour via Belgium or crossed by ferry. This unsatisfactory transport link signifies major economic disadvantages above all for Zeeuws-Vlaanderen. The first fixed link for road traffic between the communities of Terneuzen and Borsele are to be created by means of the two 6.6 km long tunnel tubes down to 65 m below sea level.

Jan 1, 2003

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997

By KALLAM VK REDDY, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

Mining activity around the world has increased significantly to meet stepped-up demand for various metals [1]. Apart from the target minerals, mining also generates huge amounts of unwanted minerals that exit the mines as overburden. Due to the active mining activity, high-grade mineral resources are being depleted, leaving inferior-quality ores [2]. The mining of low-grade ores further increases the amount of overburden/waste per ton of metal equivalent of ore mined. Currently, overburden and other mine waste is most commonly used in the construction industry and as feedstock for making cement and concrete, but the overburden can also be used as a source of valuable minerals and metals [3]. 

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By Victor L. Steven

10.1-SHAFT SINKING AND RAISING BY CONVENTIONAL METHODS VICTOR L. STEVEN 10.1.1-SHAFT SELECTION A great deal of thought and planning should go into the selection of a mine shaft to provide the most effective use over the greatest, period of time. It sometimes is better to make an additional capital expenditure in the initial shaft program to achieve the greatest overall shaft usage. It is possible to sink a shaft which could be used for mine development, and initial production and later convert it to a ventilation, service or escape shaft. It is important to consider a second shaft in the original planning to provide ventilation, an escapeway and services for overall efficient production and safety. A second shaft usually is required to comply with state and federal mining laws. The main items to consider in shaft selection are: 1. Installation from surface or underground. 2. Vertical or inclined (sec Sec. 10.1.4L for discussion of factors involved in choice). 3. Tonnage to be hoisted. 4. Size of mining equipment to be lowered through the shaft to the underground workings. 5. Amount of water to be handled in the mining operation. 6. Ventilation requirements. 7. Type of ground the shaft is to be sunk through. 8. Position of shaft with relation to ore body. After the main features of a shaft arc determined, such as vertical or inclined, shape, size, type of lining and support, compartments, and shaft. facilities (air, water, ventilation, pump lines, power cahles, etc.), then :I sinking plant and procedures should be planned. At this point it should be decided whether the company will sink the shaft with its own crews or award the job to a competent shaft contractor. Company sinking generally will cost less if competent shaft men are available. Money also will be saved in plant costs, such as for hoist, headframe, compressed air, buildings, etc., as these will be part of the permanent plant and can be used in the sinking operation. Labor costs generally will be lower than contractor construction rates. The advantage of having a contract, or is the speed of completion of the project. Contractors usually have headframes and hoists ready to move on the job immediately and have trained crews ready to complete the project in the shortest possible time. Next, the type of surface sinking plant (hoist, headframe, etc.) should be selected and a determination made whether it is to be temporary or permanent. In most cases it is less expensive to install the permanent, headframe and hoist, and use them for sinking. The type of actual sinking equipment to be used should be evaluated for the most efficient sinking cycle, e.g., mucking method, drilling method, and lining or support means. The proper cycling of drilling, mucking and lining is extremely important in obtaining the most favourable sinking costs. 10.1.2 - GROUND STABILIZATION AND WATER CONTROL Prior to the shaft-sinking operation an investigation should be made into ground-water conditions. If water is anticipated, then pregrouting of the ground

Jan 1, 1973

By L. C. Lang

INTRODUCTION The introduction of 165-mm (61/z-in.) holes to underground mining operations has made possible the application of Canadian Industries Ltd's (CIL) vertical crater retreat (VCR) mining method, illustrated in the accompanying sketches. This unique and revolutionary new application of spherical charge technology (see the Appendix), when applied to primary stopes and pillar recovery, eliminates raise boring, slot cutting, and dilu¬tion of ore by backfill; greatly improves fragmentation; reduces labor and time requirements; eliminates uphole drilling and blasting; and minimizes or completely elimi¬nates damages by blasts to the walls and retreating backs of the stope or pillar. If vertical large diameter holes are drilled on a designed pattern from a cut over a stope or pillar to bottom in the back of the undercut, and spherical charges of explosives are placed within these holes at the calculated optimum distance from the back of the undercut and detonated, a vertical thickness of ore will be blasted downwards into the previously mined area. Repeating this loading and blasting procedure, min¬ing of the stope or pillar retreats in the form of horizontal slices in a vertical upwards direction until the top sill is blasted and the mining of a stope or pillar is completed. The VCR method is also applicable to drop raises and has the potential to replace all other raising methods under most circumstances. PILLAR RECOVERY Levack Mine Inco Metals Co., Ontario Div., provided the first opportunity for the method in pillar recovery. The Levack mine's high grade ore pillar No. 4800 on the 975-m (3200-ft) level was used for the production¬scale experiment (Figs. 1 to 3). The pillar was about 49 m (160 ft) long, 6 m (20 ft) wide, and 20 to 26 m (65 to 85 ft) high. The mined area on both sides of the pillar was backfilled with a 1:30 cement:sand mixture. The pillar was removed in two phases. In phase 1, the standard uphole method was used to blast down the 18-m (60-ft) long section of waste from the bottom of the ore into the undercut. From the pillar's top sill, 165-mm (61/a-in.) holes were drilled downward into the pillar, and by measuring the depth of the holes, the results of the uphole blast were determined and roof line 1 was established. The bottom of each hole was plugged, then filled with sand to place the center of gravity of each spherical charge (loaded from the top sill) at a predetermined optimum distance from the horizontal free surface. The charges were then detonated. After detonation, both draw drifts were full of extremely well-broken material. The depth of each hole was measured again, and the plot of these depths re¬sulted in roof line 2. The same blasting procedure was repeated and the resultant new back elevation was marked by roof line 3. The poor results of the initial uphole blast at one location (notice the peak in area 1) appeared to influ¬ence the subsequent new backs. A third blast success¬fully evened the back, and resulted in roof line 4. An unblasted slab averaging 6.3 m (20.9 ft) thick remained below the pillar's top elevation as the final sill. In all three spherical charge blasts fragmentation of the blasted material was extremely fine. The backfill was fully exposed on both sides of the now-blasted pillar. The backfill remained undamaged and the ore was not diluted by sand. The remnants of all the 165-mm (61/2 -in.) holes remained clean and undamaged, and the holes had well-defined bottoms that could be easily measured and plugged. Each blast took down a 3.9 to 4.2-m (13 to 14-ft) thick horizontal slab of ore. Productivity was three times greater than that of the previously practiced cut-and-fill method. Since this was the first such experiment, blasting the remaining 6-m (20-ft) thick final slab was the sub¬ject of some deliberation. If the described method was repeated, we could have ended up with a 1.8-m (6-ft) thick sill unsafe to work on. It was therefore decided to blast the whole sill using two spherical charges prop¬erly placed in each hole, but with the application of

Jan 1, 1982

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By K. A. Natarajan

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration, namely, nitrogen, air and oxygen on ball war was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. 'Marked ball grinding, tests along with electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen towards wear (corrosive wear) is relatively small and abrasive wear appears to be significant. Rheological properties of the slurry-appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1983

By W. J. Maloney, H. E. Tuneblom, A. J. Smith

The development of a large regional water supply in Southern West Virginia faced several hurdles. This paper deals with the design and construction of the intake shaft where a combination of cutting edge mechanical excavation technologies were utilized to produce a world class project.

Jan 1, 1999

By John C. Brower

The purpose of this paper is to examine the Gays in which- the policies of the U.S. government, mining companies and third world countries affect each other with regard to the availability of minerals. The interaction involves U.S. policy towards the mining industry, the policies of the companies themselves, and the policies of third world countries towards the U.S. and multinational companies. It is assumed in this discussion that U.S. policy will continue to be to seek certain minerals from abroad rather than attempt to develop domestic sources for all its requirements. This would seem to make sense both from the standpoint of cost, and for preserving what domestic resources there are so as to maintain some degree of market leverage. In today's jargon, this means greater dependency on the "third world", which, for this discussion, includes virtually all the nations in Africa, South America and Asia. Concern for availability raises the important distinction between dependency and vulnerability, and as the Director of the Bureau of Mines has pointed out, the two are not the same. Dependency is not neccessarily a bad thing; it is vulnerability that counts (Norman, 1980)

Jan 1, 1982

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

By Y. Gonzalez

The reaction kinetics of sulfuric acid leaching of brass foundry flue dusts were studied. As received flue dusts were separated into two size fractions, a coarse fraction (median size 103.5 microns) and a fine fraction (median size 3.4 microns). Experiments were performed on both fractions al-though most results are reported for the coarse fraction. Leaching experiments were conducted in a stirred reactor to determine those factors which govern the kinetic response of the sys-tem. The kinetics were followed by determining the increase in the concentration of dissolved copper with time. The effects of temperature, concentration and oxygen partial pressure on the rate of copper dissolution were examined. In addition, reaction residues were examined by SEM, EDAX and X-ray analysis. An activation energy of 4.8 kcal/mole (20.08 kJ/mole) was calculated. The rate was found to be significantly dependent on oxygen partial pressure and acid concentration. The order of the reaction with respect to oxygen partial pressure and hydrogen ion concentration was approximately 1.50 and 0.37, respectively. Results indicate that the dissolution reaction is limited by diffusion and can be described by the following mathematical expression where ~ is fraction of copper extracted in time t

Jan 1, 1988

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By Gary F. Meenan

The industrial practice of froth flotation for upgrading the quality of fine coal is a relatively complex, expensive, and inefficient process when compared to the coarse- and intermediate-size coal cleaning circuits. The differences in cost and process efficiency can be attributed mainly to the lower equipment throughput, the added cost of flotation reagents, and the fact that flotation is typically a manually operated process susceptible to fluctuating feed characteristics that influence the overall operating efficiency. The emphasis in recent years has been on improving the flotation process efficiency and lowering the cost per clean ton. This has been achieved by larger flotation cell designs, implementation of flotation reagent evaluation programs, and improved process instrumentation and control. These developments are reviewed along with other current coal flotation practices.

Jan 1, 1999