Search Documents

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By R. L. Grayson

Compliance standards for respirable dust which are reduced because of high quartz concentrations have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1990

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By Bernard Y. Saltie

The White Pine orebody is characterized by a high lateral stress or highly faulted and joined conditions. Because of these difficult conditions roof support has always been a main concern. Mechanical bolts were widely used in the early seventies; however, it became apparent that major improvements in ground control were required if safe operation at White Pine was to be continued. The first step was taken in 1973-1974 with the testing of resin bolting. Record of caves and roof-falls with either type of support demonstrated superiority of resin bolting versus mechanical bolting - Safety was dramatically improved which was the absolute first consideration; however resin bolting was still more expensive than mechanical bolting. In order to generalize resin bolt installation, the second step was therefore to acquire special roof bolters compatible with resin bolting. The machine was to enhance the safety of the operation. This was achieved by the acquisition of the Secoma bolting machine equipped with an automatic bolting turret. Being a "hands off" operation the safety of the operator is total. Using a fixed taped attachment of the drill steel on the chuck a front guide and an automatic regulator torque thrust on the steel drilling in small diameter was possible. Being a fully automatic process only one operator is required per machine versus two operators with the conventional machines. The two main objectives were reached enabling the extension of resin bolting to the whole mine.

Jan 1, 1980

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or 'greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By T. Gupta, T. Ghosh

"In recent years, the demand for Rare Earth Elements (REE) have grown rapidly due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources of REEs, possibly Coal and Coal byproducts. Coals from certain parts of the world can be rich in REEs, and can approach a total concentration of 1000 ppm. Two Alaskan coal samples were investigated for the effect of size and density on the concentration of REEs on three selected size fractions. Flotation tests were conducted for finer fractions. Additionally Bottom ash and Fly Ash samples from a power plant have been examined for REE concentration. The results show that the upgrade potential for REEs on ash basis from whole coal basis ranges from 2:1 to 4:1 for Wishbone Hill and Healy coal samples respectively. Flotation of the finer fraction for both coal samples, conducted under similar conditions, reveal higher concentration of REE’s in the tailings. Both coal samples have a comparatively higher LREE content than HREE. Trends of REE content of the power plant products on ash basis revealed that Fly Ash has a slightly higher concentration of both LREE and HREE than Bottom Ash. Keywords: Rare Earth Elements, Coal, Coal Ash INTRODUCTION Rare Earth Elements (REEs) and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in green power generation such as the manufacture of wind turbines and also in hybrid cars. Europium, Terbium and Yttrium are used for devices that have visual displays such as computer screens and laptops [1, 2]. REEs pose fewer environmental problems of disposal and recycling than conventional heavy metal counterparts [1]. Rare-earth metals are key ingredients for radar systems, avionics, modern national defense and satellites [2-8]. In the last 25 years China has been mining, processing and refining Rare Earth elements at affordable prices thus gaining a virtual monopoly in the market. The many fold rise of the prices of REE elements over the last few years and frequent disruptions in supply has forced various nations to invest in indigenous extraction of REEs by increasing production from previously productive sites and to expand the production from new alternate sources including coal and coal byproducts [9]. Coal and Coal beds have been found to be significantly enriched with certain critical metals and can be a potential source for both Light Rare Earth Elements (LREE) and Heavy Rare Earth Elements (HREE) [10]. Moreover, coals with high REE concentrations have been discovered in Pavlovka and Rakovka coal deposits in Russia, Appalachian deposits in USA, Sichuan Basin deposits in China and others across the globe [10-13]. A recent study from China looked at how different trace elements (including numerous REEs) partition in various size fractions of Antaibao coal from China. The finding indicates that the REEs, phosphorous, and thorium all have their high concentrations in the particle sizes 0.5 to 3 mm, and 6 to 25 mm. REEs are also often present in the form of phosphates such as monazite in coal [13, 14]. The objective of the study is to identify the concentration of REEs in Alaskan coals and to investigate the effect of density and size in the distribution of REEs in coal and coal byproducts."

Jan 1, 2016

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By Robert C. Freas

The Northeastern United States is the most highly urbanized region in North America. It is also an area with a tremendous appetite for stone products. Within this context limestone has truely become an "urban ore". Its uses extend from traditional aggregate markets to lawn and garden, archetectual, chemical, agricultural, industrial, and environmental applications. This paper looks at both the occurance and uses of limestone in the northeast, and briefly examines changing patterns in consumptive use.

Jan 1, 1985

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By David M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been evaluated for: potential use, chiefly as structural clay products, refractories, and lightweight aggregate; lithology; physical properties tests; fired tests, both quick-fire and rotary kiln; major-element chemical analyses, and quantitative five-component X-ray mineralogy for quartz, mica, feldspar, kaolinite, and chlorite-vermiculite-montmoril-lonite. Approximately 80 percent of the samples are of some potential use. Of 220 shale samples, 84 were potential lightweight aggregate sources and 83 potential brick sources. Binary correlations of test data versus potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to super-duty refractories and lightweight aggregate; kaol-finite content for refractories versus low-temperature fired product sources; quartz content illustrating that there is an apparently necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 40 percent minimum for lightweight aggregate; carbon dioxide, which is low for refractorfes, beneficial in lightweight aggregate, and probably restrictive for some tiles choroite yermicalite, which is low for refractoies and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries, and perhaps a future potential for aluminum from shales that exceed 20 percent A12Q3.

Jan 1, 1971

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976