Search Documents

By Bernard A. Grand, Gary A. Almeraris

This project involves the reconstruction of a 1,100 ft. long by 75 ft. wide segment of an existing 4 to 5 track subway under Northern Boulevard in the Borough of Queens in New York City. The project includes widening the existing subway to permit the construction of new inbound and outbound subway (T1 and T2) ramps adjacent to and under existing operating tracks. The plan of the project is shown in Fig. 1. Existing tall buildings along the job site and a contaminated groundwater plume under an adjacent rail yard required construction of slurry concrete walls along the east and west construction limits. Groundwater cutoff across the north and south construction limits of the subway was achieved by jet grout walls built across the subway invert slab between existing track and third rails. The work involved dewatering the construction site to a depth of about 50 ft. below street grade. This is a four year project and includes extensive work to maintain and protect subway and vehicular traffic of over half a million commuters a day through the work area. The project cost was $160,000,000.

Jan 1, 1999

By J. Roth

PROLOGUE Nowadays, where production costs and energy costs are increasing and at the same time requirements in fineness and purity of industrial mineral products are getting higher and higher, industry has to look for more efficient grinding systems and developments to produce these products more economically. Therefore lots of new developments in high energy jet mill pulverizing have been made. In the main, however, these developments involved more or less just the new principle of fluidized bed jet pulverizers but not the older spiral jet mill principle. In some cases, especially in the filler industry where laminar minerals are used and higher aspect ratios are required, the spiral jet mill principle has advantages in a better delamination of these minerals. To comminute minerals down to products with a d97 < 3 µm, the specific energy consumption increases up to 2,000 kWh/t – 3,000 kWh/t or even more, depending on the grindability of the mineral. So the production of these fine materials is quite an expensive task. But jet mill grinding is and will be the most favorable method to produce micro-products and in the near future nano-products, despite the high energy consumption.

Jan 1, 2000

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the &apos;T&apos; bracing principle. Previously, Jarva&apos;s line of tunnel boring machines, even their smallest, was designed on the &apos;X&apos; or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the &apos;T&apos; scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By Hassan Madani, A. Malek Mohammadi

Dorreh barite mine located in the central part of Iran is one of the largest barite mines, in the country. The mine is subdivided into three blocks, which are called block 1,2,3 according the barite quality. In the central part of each block, a heavily concentrated grid of exploratory drill holes have been drilled and the reserves of area was calculated based on these holes, some years ago. It was decided to compute the reserve of the area by geostatistical methods, in the form of an M.Sc. project. In order to study the area, three regionalized variables including density, thickness and density-thickness (accumulation) was studied and the spherical variograms were fitted to these variables. These models were evaluated by cross-validation method. The optimized block size was chosen in order to compute the reserves by kriging method. The reserves of explored parts of each block of mine was calculated and the results were extended to the whole area of the blocks. The reserve of the explored parts and the total reserve of the area were calculated to be 96,000t and 1,670,000t respectively.

Jan 1, 1996

By Darryl J. Butcher

The Akjoujt Project is operated by MORAK SA, a company incorporated in the Islamic Republic of Mauritania. MORAK is jointly owned by General Gold International SA (A wholly owned subsidiary of General Gold Resources NL.), SAMIN, and the International Finance Corporation. The project was devel­oped to treat approximately 2.1 million tonnes of TORCO (Treatment of Refractory Copper Ores) tailings containing an average 3.2gAu/t, and 0.75%Cu/t. The process involves the use of ammoniacal cyanidation for gold extraction, and conventional carbon adsorption, and eventual desorption, of gold values. This is believed to be only the second commercial application of this leach chemistry in the world. The other being a small vat leach operation on the Paris Mine Dumps. (This operation was described by Mr M Ruane in a paper to a previous Randol Forum.) Initial work on the process, and the Akjoujt process design assumed that the reaction involved was anaerobic. This paper describes the operating experience, plant trial, and eventual installation which has lead MORAK to the conclusion that the process is not anaerobic, but requires oxygen, or an oxidant to proceed.

Jan 1, 1995

By Norbert Patzelt, Hans Knecht, Wolfgang Baum

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To compound problems, average head grades for refractory U.S. gold ores have fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Particularly in hard, (semi)refractory sulfide ores, many operations may experience substantial decreases of gold recov­ery. For example, Martins et al. (1991) report that at an Austra­lian mine, sulfide ore treatment led to 4 - 10 % lower gold reco­veries as the work index increased from 8 kWh/t to 14 kWh/t and the grind coarsened. Many refractory ores should actually be classified as semirefractory since a fine sulfide fracturing and liberation would make 80 - 90 % of the gold cyanide leachable. However, conventional comminution is often prohibitively expensive for these ore types.

Jan 1, 1995

By K. A. McDonald

Hibernia de Mexico SA de CV, based in Durango, Durango, Mexico built and put into operation a 700-t/d (770-stpd) agitated cyanide leach plant in Guanacevi, Durango. Plant construction began in March 1993 and operations began in November 1993. Hibernia de Mexico, a wholly owned subsidiary of Hibernia Holdings, Inc., is a privately held Tucson, AZ-based company. The startup procedures described here deal with Mexico&apos;s legal, import-export and finance requirements, and labor and security requirements. The 700 t/d (770 stpd) Guanacevi project is located next to the town of Guanacevi. The project is an agitated cyanide leach plant built to process about 2 Mt (2.2 million st) of flotation tailings over its life. The plant is operated by Servicios de Guanacevi, Asociasion en Participacion. It is owned jointly by Hibernia de Mexico and Metalurgica Guanacevi SA de CV. Legal, importation of equipment and financing For a foreign company to operate in the mining industry in Mexico, it must form a Mexican company. A Mexican company presently must be at least 51 % owned by a Mexican entity. The other 49% may be owned by non-Mexicans.

Jan 1, 1994

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By J. R. Carr

A crucial concern when implementing computer algorithms for geostatistical analyses on microcomputers is speed of execution. Kriging, in particular, typically relies on a Gauss elimination algorithm to solve for weights. Because such an algorithm is required for each estimate, the solution for weights can result in very slow program execution speed on a microcomputer. One approach to enhancing the efficiency of Gauss elimination is demonstrated herein. The upper triangle plus diagonal of the intersample covariance matrix is used in a modified banded Gauss elimination algorithm. Results show that such an algorithm yields approximately a two-fold reduction in execution time for kriging when the number of nearest neighbors used for estimation is large.

Jan 1, 1990

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By Peter F. Howard

The lower Middle Cambrian phosphorite deposits of the Georgina Basin shown in Figure 1 were found in the period 1966-1968 by three companies, namely, International Minerals and Chemical Corporation, Continental Oil Corporation and Broken Hill South Limited. Of these deposits the significant ones are Duchess, Sherrin Creek, D Tree, Lady Annie, Lady Jane, and Wonarah which together aggregate several billion tons reserves of phosphate. Due to the economic factors of freight costs to the coast and softening of the world market price for rock phosphate, none of them is in production, nor is any in the development stage. This paper reviews the historical background to the discovery of these deposits and then deals principally with the discovery of non-outcropping phosphorites in the Barkly Tablelands of Northern Territory by the interpretation of gamma radiation logs of abandoned water bores.

Jan 1, 1971

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.&apos;s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By Robert A. Bauer

Introduction A longwall mining demonstration currently in progress in the Herrin (No.6) Coal Member near Benton, Illinois, involves the extraction of three adjacent panels by the longwall method. The first panel was completed in May, 1977. The Illinois State Geological Survey is involved in this project for two reasons: (1) to detail the geology of the roof and relate the geologic features to the behavior of the roof during mining operations, and (2) to study the nature and occurrence of coal balls (carbonate petrifactions of peat) encountered during this demonstration. General Geology of Area The stratigraphic sequence of beds immediately above the No. 6 Coal in this area, ranging from oldest to youngest, is: gray shale (Energy Shale Member), black carbonaceous shale (Anna Shale Member), and argillaceous limestone (Brereton Limestone Member) (figure 1). In some areas of the mine, where one of these units may rest directly on the coal, one or more of the members is absent from the stratigraphic sequence. The nature of roof for the area is shown in figure 2. It is greatly exaggerated in the vertical direction. The Walshville Channel, 11.3 km west of this mine, was a river at least in part deposited at the same time as the coal. The gray shale wedge on top of the coal, which thins away from the channel, is thought to represent an overbank deposit of mud from the channel. The next layer deposited on top of the gray shale, and on the coal not covered by gray shale, is the black carbonaceous shale, believed to represent a mud deposited in a brackish environment. The area where the roof lithologies change rapidly from one shale to

Jan 1, 1977

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

During 1993, contraction of indus¬trial economies in Germany (-2%), France (-1 %), Japan (-0.1 %), Eastern Europe (-2%) and the former Soviet Union (-13%) dimmed prospects of a robust economic recovery for North America. Some European countries that suffer from high unemployment and large government deficits have non-com¬petitive cost structures that will require long-term economic reforms to solve. Restructuring in the United States also continued in 1993. The sluggish pace of the US economic recovery, in¬troduction of federal tax increases and the persistence of high levels of unemployment did little to inspire consumer confidence. By the end of the year, however, sales of consumer durable and capital equipment began to grow. Depressed demand for minerals by industrial economies in recession was partially offset by continuing rational¬ization or abandonment of non-competi¬tive productive capacity in Eastern Eu¬rope and the former Soviet Union. Al¬though aluminum, lead, titanium sponge and zinc prices fell, increases in copper and steel consumption helped steady their prices along with prices of some alloys. Cash flow to the mining industry - the primary source of exploration funds - was therefore constrained. For many companies, exploration expendi¬tures were reallocated geographically and in terms of commodities sought.

Jan 1, 1994