Search Documents

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By M. K. Gangal, E. D. Dainty, G. Kunchur

This paper presents a validation of C02 as a single surrogate measurement for other diesel-emitted pollutants in multi-diesel-machine operations typical of small underground mines. This means that the simple measurement of C02 alone can be used to estimate the concentrations of other components of diesel exhaust in the mine environment. The linear relationship of C02 concentration with other diesel-emitted pollutants was indicated by the results of simultaneous real-time monitoring of C02 with CO, NO, NO2, SO2, Respirable Combustible Dust (RCD), and Air Quality Index (AQI) in several small underground mines. The SO2 was not directly measured but calculated from the measured C02 concentration and diesel fuel analysis for carbon, hydrogen and sulphur. The measurements were made in the return air drift under various mining conditions involving a number of diesel LHDs and haulage trucks. The statistical analysis and mathematical representation of the several components of diesel pollutants with C02 are presented. Regression analysis shows that at the 1 percent level of significance there is a strong linear relationship of these diesel pollutants with C02. This relationship is discussed in detail, concluding that C02 measurement alone is a good indicator of overall mine air quality and can be used as a control parameter.

Jan 1, 1991

By David R. Maneval

At the turn of the century the keys to industrial success were coal and iron. At that time, Pennsylvania was the ranking mineral producer among the States and close to 90% of the Nations energy output was generated by coal. The growth of this Common-wealth into the greatest industrial State in the nation has been due to the huge resources of easily accessable coal found by the early settlers. It was the development of these deposits that provided the United States with a new source of fuel energy. For nearly a century, the Commonwealth was the chief powerhouse of our nation and the chief source of its industrial blood and bone. In 1928 it was truly said that coal was king in Pennsylvania. Pennsylvania that year mined a billion dollars worth of coal. A single train carrying this output would reach more than twice around the world at the latitude of Pennsylvania. Coal formed nearly 67% of the freight of Pennsylvania and was responsible for its four billion dollar iron and steel industry. Coal was the real reason why Pennsylvania although 32nd in size was second and not tenth or fifteenth in wealth, population and industry. Pennsylvania was slow to take-up her heritage as the greatest coal producing State in the union. But the knowledge that coal was present was not slow in accumulating. In fact the Indians were aware of its existence long before the white man arrived. They knew that many of the hills were underlain with black stones that would burn. It is reasonably certain that Arnold Viele, the first white man to cross the mountain in this State saw coal in them in 1692. But awareness was not enough. The population in these days was confined to southeastern corner of the State and the population at this time had little need or interest in the resources further inland. Pennsylvania anthracite was discovered in 1762 but was first regarded only as a curiosity. Commercial productions started in 1820. This stimulated the development of many native industries and extensive canal system and afterwards an elaborate net-work of railroads were constructed at great costs to bring the products of the hard

Jan 1, 1971

By Patti J. Best

The Southern Powder River Basin (SPRB) now commands 30% of the US utility, coal market due to the region's low mine production costs, competitive rail rates and low sulfur content. In 1997, production exceeded 240 Mt (265 million st). This was an in¬crease of 104 Mt (115 million st) since 1989 and 4.5 Mt (5 million st) above 1996. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) approaches. This growth will be the greatest in the southern part of the Basin where coal quality is higher. Coal characteristics SPRB coal is classified as subbituminous due to its low heating value and high moisture content. The coal is characterized by low sulfur and ash contents, low ash fusion temperatures and high reactivities. In 1997, the average heating content was 8,593 Btu/lb, with an average sulfur and ash content of 0.79 lbs S02/million [ ] Btu and 5.13%, respectively. The distinguishing characteristic of SPRB coal is its low sulfur content. Most SPRB coal contains less than 1.2 lbs S02/million Btu. This is the approximate definition of "compliance" coal for Phase II of the CA AA. Much of the coal, particularly in the southern part of the Basin, is referred to as "super-compliance" coal due to SO2 contents of between 0.4 and 0.7 lbs SO2/million Btu. The SPRB is divided into three geographic clusters based on coal quality. Mines located in the southern part produce coal with the lowest average sulfur content and highest heating content, almost 400

Jan 1, 1998

By T. Dlokweni, A. Z. Toper, A. P. Squelch, R. G. Gürtunca

A collaborative research programme called 'DEEPMINE' was established in 1998 to investigate and research the problems of mining below three and five kilometres depths. Backfill is considered as an important support strategy to alleviate rockburst and rockfall problems in current depths and it will even become a more crucial mining strategy at ultra-deep level mining. In this paper, the evaluation and the application of the current backfill design criteria to the ultra-deep level mining environment are studied and a new backfill design criteria is proposed. The new criteria suggests that backfill should still be placed 60 - 70% of the area mined with a maximum fill to face distance of three metres. Furthermore, the vertical stress generated in backfill should be between 2 - 3 MPa at maximum 25 metres from the face at a corresponding strain value of maximum 10%.

Jan 1, 2001

By Simon W. Houlding

This paper summarizes recent developments in computer modelling and estimation technology. Significant improvements in computational and modelling efficiencies have advanced technical computing to the stage where, for the first time, it can be realistically applied to short-term mine planning and production control. Real-time interactive grade estimation of complex shapes, volumes and grade distributions, based on immediate turn-around of production sample grades, is now possible. An added benefit is the ability to produce complete geostatistical estimates which include confidence limits. These can be incorporated into the decision making and risk assessment processes of production control. Why the need for new technology? What is wrong with the conventional methods which have sufficed for the last thirty years? The response is manyfold. They suffer from inefficient computational processes and conflicts with geostatistical theory. They are responsible for constricting the flow of information between the disciplines involved in the mine production process. Finally, it is illogical to approximate irregular geological and mining volumes with orthogonal sets of rectangular blocks. Geological materials do not occur in block formation; and mining methods which excavate rectangular blocks have yet to be developed. Other computer based technologies have evolved out of the dark ages of rectangular approximations and have successfully dealt with irregular three-dimensional geometries. It is time for computing in the mining industry to follow this example and take full advantage of available technology. To provide the necessary background, consider the basic requirements for successful implementation of technical computing within the mine production process.

Jan 1, 1992

By Richard J. Goff

Technical Support, one of several major organizational units in the Mine Safety and Health Administration, provides technical assistance to the mining community in all areas of health and safety. One of its many areas of expertise is noise control. Depending upon the needs of the operator or inspector, the services provided can range from locating major noise sources to actually building noise controls. Over the years a vast amount of knowledge has been obtained as to what will work and what will not. DESIGN GOALS While many noise controls have been developed for mining equipment and operations, the most acceptable (ergo successful) have achieved the following design goals: - a noise level reduction of at least 5 decibels; - minimum interference with production; - inexpensive to install; and - effective in reducing low frequency noise.

Jan 1, 1984

By H. B. Charmbury

In Pennsylvania there are two distinct coal regions, bituminous and anthracite, in which the mining conditions and production trends are different. Bituminous mining is more mechanized, and production is increasing. This report is concerned specifically with the bituminous area. The bituminous coal industry apparently is facing a shortage of miners and mine officials which may become acute by 1970. Since 1949, when Pennsylvania had more than 100,000 bituminous coal miners, the number has steadily decreased. There are two principal reasons for the decrease of certified miners and mine officials. These reasons are the fact that apprentices are almost a thing of the past and the fact that the image of the coal miner is a poor one to people in general and to parents in particular. This has contributed greatly to the high average age of our miners today. The average age of all those employed in the mines is 50. Yet it is known that the progress in mine mechanization requires younger and more alert men to operate the newer type equipment.

Jan 1, 1966

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

By A. P. Gentsch

Commercially mined calcium carbonate is normally found near the surface in the United States. It is nun& either by open pit or underground methods, depending upon its geologic setting. Processing ranges from simple crushing to the more sophisticated ultrafine processes. Intermediate steps are pulverizing, screening, beneficiation, classification, fine and ultrafine grinding, and surface treating. These processes are performed both dry and/or wet resulting in powdered or slurry end products.

Jan 1, 1986

By Phillip O. Tyree, R. A. Metz, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval corporation has produced more than 88 percent of that total.

Jan 1, 1992

By Richard J. Robbins

Mechanical raise and tunnel boring are new techniques to most of the mining industry. Coal, salt and potash have been bored economically, but until recently boring machines were not designed specifically for rock boring in underground mining. The construction industry has led the field of rock boring since 1854 when the first tunnel boring machines built by James S. Robbins and Associates went to work at Oahe Dam, South Dakota. Since that time the company has built boring machines for tunneling through ground conditions varying from cohesionless soil to hard rock, and in diameters ranging from 7 feet to 36 feet 8 inches. It is natural that the construction industry got the jump on mining with the use of mechanical rock boring equipment. Mines have looked for the long range answer to problems of underground excavation and they have chosen proved and established techniques they expect to employ for the next ten or twenty years. The mine development was laid out to accommodate these techniques.

Jan 1, 1964

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By Dale C. Matthews

Pressure oxidation of refractory gold ores is becoming more popular in our environmentally sensitive society. This paper will discuss some specific process problems and solutions involved with starting up and operating an autoclave circuit.

Jan 1, 1991

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993