Search Documents

By P. J. M. van Heteren

The flotation system is usually distinguished from other physical chemical systems by the importance of interactions at the solid-liquid and solid-gas interfaces. In recent years, numerous quantitative studies have been made of the distribution of common collectors between the solid and aqueous solution phase. Although in flotation the main emphasis is placed on the adsorption process, chemical reactions will also take place in the bulk solution phase, These side reactions are often undesirable and will contribute towards the complex behavior of many a flotation system In sulfide flotation, the precipitation of insoluble base metal xanthates is a well-known phenomenon although the conditions under which the precipitation reaction will proceed and the magnitude of the solubility products are not known with accuracy. A knowledge of the solubility of these xanthate salts will not only be of value in flotation research, but the mill operator might be interested in knowing whether precipitation of metal xanthate can be controlled or completely prevented in the flotation circuit thereby reducing reagent consumption, For these various reasons the solubility of lead, copper, zinc, and silver ethyl xanthate was determined. The experimental techniques and results will be discussed in this paper.

Jan 1, 1958

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

By Thomas A. Simpson

Heretofore, underground coal mines in Alabama have operated under only 60 to 360 meters of cover: however, new mines (at least 5 in the early opening or development stages) will be operating under cover ranging from 600 to 660 meters. With increased rock confining pressures, roof stability problems will become more critical. Initial studies in two 7 ½ -minute quadrangle areas in the Warrior coal basin of Alabama indicate that the orientation of certain lineament and fracture-trace modes mapped from ERTS-1 (Earth Resources Technology Satellite) imagery correlate closely with the strike of joint and fault modes. High altitude (118,000 m) U-2 aircraft data were used to support these findings. In addition, over 50 percent of the normal faults mapped in the study area could be directly correlated with ERTS and U-2 lineaments and fracture traces. These correlations provide clues to the structural development of the Warrior coal basin and may, in turn, be used as a guide to the prediction of roof-stability conditions in advance of mining.

Jan 1, 1975

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By L. G. Austin

A simple finite difference algorithm has been used to compute a simulation model for unsteady-state ball milling. The model considers the mill to act as if it were three fully-mixed reactors in series (one-large/two- small), it incorporates the-Rogers-Austin mass transfer law relating mill hold-up to flow rate through the mill, and it allows for the reduction in breakage rates caused by over-filling of the mill at high flow rates. The computation is rapid and requires only small storage space. Examples are given of use of the model.

Jan 1, 1984

By N. Kuroda

A realistic simulation model has been used for designing longwall mining, especially for solving operational problems. This paper describes background, development, validation and some applications of the simulation model for mining people who are unfamiliar with O.R. or computer technique, as a simple planning tool. The following items were established: logical analysis and algorithmic design for practical longwall mining, structure of hypothesis behavioral organism, input parameters, using practical knowledge and operational statistics of the mechanized longwall system experienced for many years.

Jan 1, 1982

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department&apos;s Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977