Search Documents

By Wiston Rocher

The Minera Ojos Del Salado (MINOSAL) concentrator is located 20 km (12 miles) southeast of Copiapo, Chile. It processes copper ore provided by its Santos and Resguardo mines at a capacity of 4.2 kt/d (4620 stpd). In 1982, Phelps Dodge acquired the majority interest in MINOSAL to explore the property's potential. At that time, the concentrator plant was a small, antiquated installation with a capacity of 674 t/d (740 stpd). At the time of the pur¬chase, the majority of the ore was produced from the Santos and Resguardo mines, but custom ores of copper, silver and gold were also treated. The acquisition occurred at a crucial time in the copper business, since the price had fallen to nearly 50 cents/ lb. In 1985, Phelps Dodge purchased the outstanding interest in MINOSAL and acquired 100% of the property. Today, after numerous improvements and two expansions, the concentrator is a combination of old and new equipment. The regrind mills, for example, have been in service for about 50 years, while the ceramic concentrate filter represents the latest technology.

Jan 1, 1993

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By F. Calizaya, I. Duckworth

An ore-pass is an underground conduit used to transfer ore from one level of a mine to another. This method of transportation depends on the elevation energy only; therefore, it has very low operating cost. However, two inherent problems may hamper this process: (1) hang-ups of interlocked pieces and (2) a sudden release of trapped air from the ore-pass (belching). These events can create unsafe conditions with the potential for catastrophic consequences. This paper presents a summary of CFD modeling studies that were formulated to investigate the pressure build-up and belching of dust and rock particles from long ore-passes. The models were calibrated against field data collected from an actual ore-pass system and used to predict the airflow-pressure distributions in the mine for various ore feed rates and ore-pass geometries. P.T. Freeport Indonesia’s Grasberg ore-pass system (240,000 tpd capacity) was used for this purpose. This system comprises of four active ore-passes, with each being more than 600 m in vertical length.

Jan 1, 2004

By Joseph A. Dos Santos

Developed in 1983, high angle conveyors - HAC®s are proven versatile systems for elevating materials continuously from a lower to an upper level. Such systems may also be used to lower materials continuously. HAC®s have found commer­cial application in widely varying materials (including coal, refuse, coarse ores [-250 mm], hot clinker, municipal sludge, wood chips, gypsum, slag, excavated earth, various grains and RDF), at widely varying throughput rates from 0.27 to 4250 t/h. The conveying profiles have varied widely and elevating heights range from 3.66 m to 175 m. HAC®s have found application in coal, copper and iron mining, and preparation, in municipal waste treatment, rapid transit projects, pulp and paper mills, cement plants and in gold mining. While noting a wide variety of applications in general, the present writing focuses on Newmont Gold's HAC®, near Carlin, Nevada, which elevates very coarse gold ore to the screening plant. Additionally, upcoming HAC® applications in gold mining are discussed and a proposed multi-flight vertical HAC® system from a deep underground mine is described.

Jan 1, 1996

By Joseph A. Dos Santos

Developed in 1983, High Angle Conveyors HAc®s, are proven versatile systems for elevating materials continuously from a lower to an upper level, Such systems may also be used to lower materials continuously. HACs have found commercial application in widely varying materials ( including coal, refuse, coarse ores, hot clinker, municipal sludge, wood chips, gypsum, slag, excavated earth, various grains and RDF), at widely varying throughput rates from 0.27 to 4,000 t/h. The conveying profiles have varied widely and elevating heights range from 3.66 m to 175 m. HACs have found application in coal, copper, gypsum and gold mining, coal preparation, in municipal waste treatment, rapid transit projects, pulp and paper mills, and cement plants, While noting a wide variety of applications in general, the present writing focuses on a very large HAG® system, consisting of eight (8) main HAG units to elevate nickel/copper ore continuously from under­ground, 1402 m (4600 ft,) vertically to the surface. It compares technical and economic aspects of such a system against traditional mine hoist haulage,

Jan 1, 1993

By Merwin Bernstein

Peru has been an important source of metals since Aug. 29, 1533. On that day Francisco Pizarro took charge of the 24 t (772,000 oz) of gold and silver that constituted Atahualpa’s ransom. At today’s prices, the value of that booty ranges between $100 and $150 million, depending on the proportion of gold to silver. Since then, Peru’s silver and gold production has been legendary. Current mine production Most of Peru’s metals are mined from the Andes Mountains and its foot-hills. The Andes run the length of the country parallel to the Pacific coastline from Ecuador to Chile, a distance of nearly 3000 km (I 875 miles). They are about 300 km (187 miles) wide and much of the range is more than 3000 m (9900 ft) in elevation. High plateaus (altiplanos) occupy a large part of the range. Both flanks are rutted by large valleys and canyons. Many of these peaks are prodigious. which make road building expensive and adds to the cost of mining.

Jan 1, 1993

By Lane White

Loading shovels are at the heart of most surface mine production. As truck sizes have increased, shovel manufacturers have matched them with larger shovels (see table, page 343). Further increases in shovel size may be in order if trucks in the 270-t (300-st) range find acceptance at the largest surface mines. However, larger shovels are not currently the primary focus of shovel design engineers. Competition and user pressure are combining to keep their work directed toward improved shovel productivity and efficiency. Computer design technology and advanced electronics play an increasingly prominent role in this work. "Improved diagnostic capability, system monitoring, vibration analysis and above all increased user friendliness in machine control systems are being pursued by most manufacturers working in our industry today," observes Stuart R. Cotterill, director of marketing for Harnischfeger Corp. The use of computer-aided design (CAD) systems in shovel design has been in place for many years. However, recent advances in computer capability and improved software programs and graphics are making computers even more useful.

Jan 1, 1995

By Claus Becker

At the RETC 1979 in Atlanta/Georgia it was reported about the beginnings of the Hydroshield system and the first site experiences. Since that time over 10 miles of tunnels in various diameters have been built with that system, and the discussion of the two most interesting projects will be the main topics of this paper. AURELIA TUNNEL, ROME In Rome, the railway system is going to be completed and modernized. Therefore, it is necessary to tunnel through the Roman hills. Part of the new railway system is the Aurelia Tunnel, located some 100 feet below the famous Via Aurelia Antigua, close to the Vatican. The double track railway tunnel has an internal diameter of 9.44 m and a length of 2.410 m. It runs through completely differing soil conditions. (Fig. 1) The first 1000 t are situated in watertight clay, the rear part in water bearing loamy, clayey sands with interlayers of loamy clays. The figure shows the soft change-over from clay to sand. The groundwater head is between [ ]

Jan 1, 1983

By Richard Newcomb

It is four years since the seminal study of demand for rapid excavation by the National Academies of Sciences (NAS) and Engineering outlined this technology's opportunities, requirements and significance to the challenges of urbanization and natural resource conservation. The demand study was quite simple. Opportunities were valued at market while requirements to produce new technologies were valued at cost. The significance of new technology in economic terms was measured by the net discounted gains to users over time. The Academy view in 1968 was that these gains, even most modestly estimated, appeared large enough to justify the bill for research proposed by that Committee (1). In 1970 the question of demands became international in what is recognized as the first international experiment in technological policy analysis, terminating in the Advisory Conference on Tunneling of the Organization for Economic Cooperation and Development (OECD)(2). A monumental demand survey formed the basis for its economic assessment. The twenty-two OECD nations also made an impressive attempt to measure the magnitude of existing research and development efforts. In their recommendations periodical statistical demand forecasting and collection of demand data (Recommendation 1) was given central importance for public planning (Recommendation 2), the financing of public construction (Recommendation 3) and the encouragement of technological advance (Recommendation 4). Their program for international cooperation led to OECD's establishment of a Directorate for Environmental Affairs, and influenced the organization of the World Environmental Conference meetings now held in Stockholm under United Nations auspices. The OECD Conference was the first example of "an attempt to apply the concept of technological policy analysis to a 'civilian' technology having potentially

Jan 1, 1997

By P. Munjal

"Usage of Supercritical CO2 in place of high pressure freshwater has proven to be a potential breakthrough in the technique of fracturing. Tapping of carbon footprints from feasible sources like industries can be used to manufacture Supercritical CO2 required for fracking. Supercritical CO2, being less viscous than water, creates complex and coherent micro-fractures which can connect many more natural fractures greatly, increasing maximally the fractures’ conductivity leading to an increment in production. The better clean-up property of Supercritical CO2 provides auxiliary benefits of immediate evaluation of fracture zones, usage of an optimized quantity of mesh proppant and elimination of the need of swabbing. Also, Coal has a stronger affinity for CO2 than for CH4. When CO2 is present, CH4 on coal is replaced by CO2. This also ensures rigorous recovery of gas from the coal beds. Use of Supercritical CO2 will obliterate many problems as the CO2 used for fracturing is either sequestered beneath the crust or is recovered at the surface and reused. Therefore, injecting CO2 into coalbeds achieves not only enhanced CBM recovery, but also greenhouse sequestration underground. INTRODUCTION Coalbed Methane At various times in the geologic past, earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath the soil. As more and more soil deposited over them, these dead plant remains were compressed. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The omnibus process of formation of coal, thus, comprises of conversion of dead plant matter into peat, followed by its conversion to lignite, then sub-bituminous coal, after that bituminous coal, and lastly anthracite. This process of enrichment of coal as it is progressively forced deeper into an ambience with higher temperature and pressure involves biological and geological processes that take place over a long period and is called coalification. During coalification, large amounts of methane-rich gas are generated and stored within the coal on internal surfaces; hence comes coalbed methane. Coalbed methane (CBM), a gas formed as part of the geological processes that are responsible for the generation of coal, is adsorbed into the solid matrix of the coal during its formation process. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoirs, as the methane is adsorbed and not absorbed. The methane is in a near-liquid state, lining the inside of pores within the coal. The open fractures in the coal that result from the liberation of volatile materials (and subsequent contraction due to the liberation) from the coal due to the high temperature and pressure conditions encountered, called cleats, may also contain free gas or can be saturated with water."

Jan 1, 2015

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By J. R. Johnson, C. G. Stewart, D. K. Myers

INTRODUCTION Radon-222 is an inert, radioactive gas formed by the radioactive decay of radium-226, a long-lived member of the uranium-238 decay chain. Radium is present in varying amounts in virtually all soils and, on the average, about 36,000 pCi (1330 Bq) of radon per square meter of soil diffuse into the atmosphere each day (UN 1977). Radon decays with a half-life of 3.6 days through four short-lived daughters to lead210 and it is these short-lived daughters[ [Ra A, (218Po, t, = 3.0 min) , Ra B, (214 Pb, t;, = 27 min), Ra C, (214Bi, t] = 20 min) and Ra C1 (214Po, t] = 2.5 x 10-6 min)] ]which cause the major health hazard associated with radon (Bale 1951). Atoms of these daughters, either unattached or attached to the ever-present particles in air, are deposited on the surfaces of the respiratory tract; alpha particles emitted in their decay can result in large doses to the cells of the bronchial epithelium lining the respiratory tract. These daughters will be present in air in varying relative concentrations depending on the "age" of the air (time since radon emanated into it) and on the amount of mixing of radon and radon daughter contaminated air with clean air. [The practical unit developed to quantify the amount of radon daughters in air is the Working Level (WL). This unit was historically related to the equilibrium concentration of 100 pCi (3.7 Bq) of the short-lived daughters of radon in one liter of air (cf. Holaday 1969) and is defined as any mixture of the short-lived daughters in a liter of air that have a-potential alpha energy of 1.3 x 105 Mev (2.08 x 10-5J) in their decay to lead-210. The working level month (WLM) was developed along with the WL, and was defined as an exposure to one WL for a working month (170 h). This is equivalent to 2.2 x 107 MeV•h•L-1 (3.54 x 10-3 J.h.m-3). If the average breathing rate is taken as 1.2 m3.h•1 (ICRP 1975), then one WLM is equivalent to inhalation of 4.24 mJ of potential alpha energy.] It is now generally agreed that the inhalation of radon daughters is the major potential radiation hazard in uranium mining, and contributes a substantial fraction to the natural radiation exposure of the general population due to the accumulation of radon and radon daughters from natural sources in buildings. Radon daughter concentrations in modern mines are controlled by ventilation, and by blocking off old working areas (cf. Simpson, 1959). However, before the hazard from radon daughters was recognized, considerably higher concentrations of radon daughters were present in some uranium and non-uranium mines. These high radon daughter concentrations resulted in an increase in lung cancers in the mining population, and it is these results that are our main source of information on the risk of inhaling radon daughters. HISTORICAL REVIEW Many excellent reviews of the history of understanding the health effects of inhalation of radon daughters are available (see, for example, Hueper 1942, Lorenz 1944, Sikl 1950, Stewart 1964, Holaday 1969, Lundin 1971, Cross 1979) but a brief summary of some of the highlights in this area may be of interest. [a] 1556: Agricola describes an unusual and fatal chest disease occurring among underground miners in the region of Schneeberg and Joachimsthal (Jachymov) in the Erz mountains in Central Europe. (It is of some historical interest to note that Agricola's book was translated from Latin into English by a mining engineer and his wife; the engineer later became President of the U.S.A.) [b] 1879: Haerting and Hesse indicated that the majority of deaths among Schneeberg miners were due to lung cancer; the lung cancers in these miners (who were incidentally not cigarette smokers) were observed twenty to fifty years after they began working in the mines. [c] 1896: Discovery of natural radioactivity by Becquerel, followed by discovery of radon by Dorn in 1900. [d] 1924: Ludewig and Lorenser report high concentrations (400 - 15000 pCi or 15 - 570 Bq per liter) of radon in the air in the Schneeberg mines and suggest that radon could be responsible for the high rate of lung cancer among miners. However, the reason why radon should cause lung cancer specifically was still not really understood up to twenty years later (Lorenz 1944). High concentrations of radon in the air in the Joachimsthal mines were reported by Behounek in 1927 and a high incidence of lung cancer among Joachimsthal miners (similar to that among miners at Schneeberg, which is only some 30 km distant but in a different political district) was noted at about the same time (Sikl 1930; cf. Sikl 1950). It is estimated that about half of the Joachimsthal miners died from lung cancer and about half from silicosis and tuberculosis (Sikl 1950). [e] 1930's and 1940's: Radioactive ores are deliberately mined in the U.S.A., Canada and other countries primarily as a source of radium for medical purposes and for luminescent dials; other radioactive ores are mined as a source of several non-radioactive minerals, while extensive uranium mining did not begin until the late 1940's. [f] 1940: Based on crude epidemiology and dose calculations, Evans and Goodman propose 10 pCi L-1 as a maximum permissible concentration of radon in continued human exposure. This is the first known recommended maximum permissible concentration for radon. This recommendation was adopted by the U.S. National Bureau of Standards in 1941 and reconfirmed in 1953. [g] 1945: Mitchell identifies the short-lived daughters in radon as a likely cause of the increased lung cancers in the Schneeberg-Joachimsthal miners

Jan 1, 1981

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By S. K. Kawatra

Three International Symposiums-the 14th International Minerals Processing Congress, the 17th APCOM, and the SME-AIME Fall Meeting special symposium on Design and Installation of Com¬minution Circuits-held in 1982 contained a number of papers relating to the fundamentals of processing coals and metallic minerals. In addition, many papers were published elsewhere in the literature. Some of the more significant papers are discussed below. Flavel reviewed key performance parameters, such as energy-size relationships for crushing processes and presented a fundamental basis for optimizing crusher productivity and possibly for development of improved crushers. Pascoe et al. reviewed the use of such control schemes. Magerowski and Karra presented a paper on a computer program developed to and in the design of crushing circuits. The problems associated with the scale-up to very large ball mills were discussed by Arbiter and Harris, and by Kavetsky and Whiten. Both groups concluded that limits on mill productivity arise due to problems associated with particle breakage and transport through mills. Austin et al., and Herbst and Rajamini reviewed the state of the art for the use of grinding circuit simulators for design and control. The effects of mill operating and design parameters on selection and breakage were discussed in detail. The philosophy of control and instrumentation for grinding circuits was extensively discussed by Kawatra and Seitz. Their paper presented for the first time an analytical basis for the inferential particle sizing technique and provided a fundamental basis for the implementation of this technique. The effect of reagent addition variation's on the performance of coal flotation circuits was reported by Kawatra and Waters, and on sulfide flotation circuits by Klimpel et al. Both groups analyzed circuit behavior from a kinetic point of view and reached similar conclusions on the effects of collectors and frothers. The computer simulation of an iron ore flotation circuit also was reported by Kawatra et al. In this work particular attention was paid to the phenomena of froth overloading. Klimpel et al., Kawatra and Waters, and Niemi et al. discussed the philosophy of control by flotation circuits from a fundamental kinetic point of view. An extension of the use of high intensity magnetic separators to the beneficiation of specular hematite was discussed by Thayer and Linkson.

Jan 5, 1983

By L. B. Rothfeld

In anticipation of RCRA reauthorization and subsequent rulemakings, the Bureau of Mines is studying potential economic impacts of RCRA on mining. For U.S. copper heap and dump leaching operations in a variety of terrains, the cost of liners and closure caps to comply with RCRA Subtitle D ranges from $55 million to $158 million per site, or about $500,000 per hectare ($200,000 per acre). If RCRA technology requirements and financial assurance had been required on current operations, 27 to 100% of production from heap and dump leaching would have been non-competitive at market prices between $2,310 and $1,650 per metric ton ($1.047 and $0.75 per pound) copper. This result is based on an analysis that considers return on capital, corporate overhead, marketing, and freight costs as well as operating and maintenance costs at the mine. Over the same price range, economic analysis using the IMPLAN input-output model on one-or two-county regions indicates potential net job losses of about 570 to 2,700 jobs. Total economic output of those counties could be reduced by about $180 million to $360 million.

Jan 1, 1994

By H. H. Murray

Tactical R & D is research and development for a specific application or applications. The mineral scientist has to define and understand the physical and chemical parameters required for a specific or potential application. Then the researcher must know the structure and composition of the mineral and its physical and chemical properties. Can these properties be changed by processing particle size and shape modification, and surface chemical treatment? Examples of tactical R & D in the industrial minerals area will be described.

Jan 1, 2003

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By D. S. Choi, H. D. Dahl, D. L. McCain

The paper examines current room and pillar mining practice in the U.S.A. from the standpoint of rock mechanics. Consideration is given to the deformation characteristics of the roof formation and the coal seam as determined in the laboratory as well as in the field. The results can be utilized by the practicing mining engineer to improve current mine design practice.

Jan 1, 1982

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989