Search Documents

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. BackgroundThe Mine Improvement and New Emergency Response Act of 2006, known as the Miner Act (U.S. Department of Labor, 2006), was enacted in the wake of three mine accidents involving explosions or fire that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the Miner Act includes provisions that target mine safety issues in areas such as emergency response planning; adoption of new technology; training and education; and mine safety standards enforcement. Section 13 of the Miner Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the U.S. Department of Labor to act on the results of such research, as appropriate. These mandates culminated in the 2009 adoption of changes to the Title 30 Code of Federal Regulations, or 30 CFR, mining health and safety regulations (U.S. Department of Labor, 2008), requiring underground coal mines to supply mine emergency RAs and associated components so as to provide a life-sustaining environment for persons trapped underground. Such RAs can be either selfcontained mobile units or built-in-place facilities. The regulatory changes also include provisions establishing requirements for the approval of RAs and their components by the U.S. Mine Safety and Health Administration (MSHA), among which are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One criterion for maintaining a safe RA atmosphere is the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in. H2O), or as specified by the RA manufacturer, above mine atmospheric pressure in the RA (U.S. Department of Labor, 2008)."

Oct 1, 2016

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By Thomas R. Doyle

When you think of the state of Maine, you probably think of lobsters or lighthouses. The last thing you would think of is metallic mineral mining, and that is for good reason. According to the Maine Geological Survey?s website, ?no metals have been mined in Maine since 1977.? Moreover, Maine?s metallic mineral mining laws and rules, which were last rewritten in 1991, have effectively made mining in the Pine Tree State impossible. Statutory changes enacted in 2012, however, put Maine on a path to make metallic mineral mining part of the local economy in the near future. History of metallic mineral mining in Maine Currently, Maine is not a metallic mineral mining state, though that has not always been the case. The 1800s saw various mining operations in Maine, including what the Maine Geological Survey calls a ?mining boom? from 1879 to 1882, where mining of iron, silver, copper, lead and zinc expanded rapidly. Mining and mining activity in the more recent past, however, drove the debate before the state legislature when this issue was debated in 2012.

Jan 1, 2012

By Howard L. Hartman

In 1969, the OECD conducted a survey internationally to determine the status and needs for research and development in the field of tunneling. The findings also have some validity for underground excavation in general and for underground mining per se. Of the 17 countries responding to the survey, the U.S. leads in the level of support: $21.8 million and 720 man-years of effort over the last ten-year period. The total volume of R/D for the 17 countries was estimated to be $86 million and 5800 man-years. Performance of research was primarily by government agencies and public utilities (70%); the balance was conducted by private organizations and universities (15% each). In the categories of R/D subjects surveyed, three--Wk mechanics, soil mechanics, and geological exploration--outstripped all the rest in priority of effort to date. Ground support, equipment development, excavation, and environmental control received intermediate attention. The subject areas in which the least R/D effort has been expended are materials handling and systems evaluation. For the future, those R/D areas rated the most crucial to achieve technological progress in tunneling were excavation, ground support, and materials handling. The survey findings of tunneling activity indicated (1) a disturbingly low level of R/D activity in the private sector, (2) the necessity for a reordering of priorities in directing research efforts in the future, and (3) a lack of recognition to date of the importance of systems evaluation in R/D activities.

Jan 1, 1970

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By Goutam H. Shahani

The current economic downturn has been at the center of media attention for several years. Today, the mining and mineral sectors are being impacted by highly fluctuating supply-and-demand conditions, extreme price volatility and tremendous market uncertainty on a world-wide basis. There have been numerous plant closings, project cancellations and employee layoffs. In this gloomy economic environment, it is easy to forget that the world?s gross domestic product (GDP) has more than doubled in real terms during the last 30 years. While current market turbulence may continue for some time, the long-term trend is unmistakably upward. Living standards are rising all over the world, thereby creating demand for food, clothing, transportation and housing. This translates into tremendous demand for the mining and mineral sectors. In the future, new capacity and plant expansions will be necessary to meet this need. These investments, which typically have a life span of 30-plus years, will have to be based on long-term economic considerations rather than current market conditions.

Jan 1, 2011

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By John Davis Morgan

The uncertain world conditions of the present time require that the United States be prepared to meet: a. all-out nuclear war with attack on the United States b. limited wars (anything smaller than (a.) c. political, economic, and/or psychological warfare. Our present position as a major world power derives in large measure from our free institutions and our great industrial productivity, and our productivity in turn depends on an ever-continuing flow of raw materials from the earth - metals, minerals, fuels, and agricultural products. The United States, with only about 6% of the world's population, uses from one-third to two-thirds of the world's annual supplies of 'most metals and minerals. The United States strategic materials stockpiling program is designed to enhance our national security posture: as stated in the preamble of the Stock Piling Act, to decrease and prevent wherever possible a dangerous and costly dependence of the United States upon foreign nations for supplies of strategic and critical materials in times of national emergency. In times past, the Good Lord himself has ordered some stockpiling. The Book of Genesis in the Bible tells how Pharaoh of Egypt was directed to set aside one-fifth of the produce of the land in each of the seven good years to meet the needs of the seven bad years that were to follow: this would be a stockpile of about two years? normal use. Our cultural heritage often reminds us of the wisdom of stockpiling, as in the case of the stories about the provident squirrels that gather their nuts in an orderly manner in the f all to prepare for the winter's cold. And the old proverb about a bird in the hand being worth two in the bush points out clearly the value of something that is directly at hand.

Jan 1, 1960

By Rustyn Sherer

Curis, the name of a new Arizona-based mineral development company, is an acronym which stands for ?Cu? (elemental symbol for copper), ?r? (recovery), ?is? (in situ, the Latin for ?in place?). The company was created specifically to advance the development of the Florence Copper Project in Florence, AZ and to pursue other next generation copper development projects in progressive jurisdictions around the world. ?We are extremely excited about this project,? said Curis Resources president and chief executive officer Michael McPhie. ?We?re here to set the standard for Greenfield in situ copper recovery (ISCR) operations in Arizona and around the world. We believe in our people, our technology and our process; and we are passionate about our commitment to environmental stewardship and community development. We?re making a long-term investment in Florence, and in Arizona.?

Jan 1, 2011

By R. Y. Wan

Recent research efforts have shown have shown selective solvation extraction of a gold cyanide ion-pair complex from alkaline cyanide solution is possible with organic phosphorus esters. These alkyl phosphorus esters such as tributyl phosphate (TBP) and di-n-butyl n-butyl phosphonate (DBBP) can selectively load gold to rather high levels, even in excess of 30 gpl. However, traditional stripping techniques are not particularly effective. In this regard, gold recovery by direct electrolysis of the organic phase has been found to be an interesting possibility. Further, the rate of direct electrodeposition from the organic phase can be improved significantly by using an aqueous/organic mixture. Direct electrodeposition of sheet gold from loaded DBBP was successfully accomplished at a current density of 8x10 4 amp/cm2 and 55°C from such a two-phase mixture with the aqueous phase as the continuous phase. No appreciable degradation the DBBP was found after 5 cycles of extraction and, electrodeposition. Finally, the applicability of the process strategy for an industrial situation was demonstrated by the successful treatment of waste gold cyanide electroplating solutions.

Jan 1, 1986

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By J. R. R. Bowling, A. McFadden, M. Francoeur

The abstract discusses the increasing use of extensive duct-fan systems in underground hard-rock mine development. It highlights the challenges of designing these systems, particularly the risk of partial vacuum and the need for careful booster fan positioning. The paper explores factors influencing the design of these systems, including component limitations, operational wear margins, and power constraints. It also defines the concept of partial vacuum and its impact on ventilation ducts. The authors propose an algorithmic approach for specifying the location and blade pitch of in-line booster fans to prevent system failure.

Mar 17, 2022