Search Documents

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By B. J. Scheiner

The Bureau of Mines has developed a system for dewatering waste slurries by flocculating mineral particles with polyethylene oxide (PEO) and dewatering the resulting flocs on static and/or rotary screens. This paper discusses data obtained from dewatering, rheology, and ion-exchange experiments. A possible mechanism is postulated for the attachment of PEO to claylike particles through a water bridge with the intershell waters of the exchanged ion and the polymer.

Jan 1, 1986

By Charles F. Stack

The A. P. Green Refractories Co. operates clay mines in ten states. Eight of these states have reclamation laws with which we have to comply and indications are that the U. S. Congress will pass a federal surface mining reclamation act in the near future. These regulations, in addition to the value of land in most areas, dictate that mining and reclamation be considered as a single operation. In many instances the land may be more valuable after properly planned mining and reclamation than before. Refractory clay, commonly called "fire clay" is defined as a siliceous clay rich in hydrous aluminum silicates, capable of withstanding high temperatures. It is deficient in iron, calcium, and alkalies and approaches kaolin on composition. Refractory clay is much more limited in occurrence and usage than common clay or shale. During 1971, common clays and shales were mined in 47 states with a total production of 45 million tons. Fire clay production was reported in 22 states with a total production of only slightly over 3 million tons.(1) Many of these producing areas are extremely limited in extent and production. Several are contained within a one or two county area. This reflects the unique geological conditions required for the formation or development of fire clay. The major fire clay producing areas in the United States are shown in Figure 1.

Jan 1, 1974

By J. D. Kennedy

The alchemists of old are remembered well for their tireless efforts in attempting to convert various common metals, such as lead, into gold. Not so well known generally, but no less intense, have been the efforts of certain individuals who attempted to manufacture diamonds over the last 100 years. Diamond, the most glamorous and permanent of gems and the hardest industrial abrasive, is carbon in a high-density unique crystalline form with a cubic structure and a density of 3.5. This contrasts with graphite at a theoretical density of 2.2 and possessing a hexagonal structure. Diamond is the hardest natural, material known and until very recently had no close competitor, natural or otherwise, with respect to hardness. The hardness of diamond exceeds that of any other industrial abrasive by a factor of approximately five. The early theories of diamond synthesis were rather vague. Since diamonds occurred in nature, man then looked to nature for clues as to how this might be accomplished. The original known diamond deposits of India are alluvial in character and provided little insight as to how diamond had been formed by nature, for in, these locales the diamonds have been washed by streams or carried by the glaciers long distances from the areas in which they occurred originally in the earth's crust. As a matter of fact, we are told that even today the locations of the mother ground for the Indian alluvial deposits are not known.

Jan 1, 1959

By Ernst P. Hall

As a scientist and an engineer whose responsibilities include the consideration of air pollution and its control, I am frequently called upon to answer variations of two basic questions, These questions may I be set forth as: (1) How much air pollution does the coal industry cause? (2) How serious is the air pollution problem to the coal industry? At first these questions may seem elementary and almost trite, but serious consideration of them will show that they are technologically involved and I further complicated by the subjective base to which they must be evaluated.

Jan 1, 1963

By Dan B. Kivari

One of the key operations in any milling circuit is grinding. Over the last two decades, large diameter Semi-Autogenous Grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Whereas earlier most SAG mills were designed to operate at fixed speeds, present day SAG mills can operate at a fixed speed or variable speed through the use of an AC synchronous motor or DC motor. However, this flexibility comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on Net Present Cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors such as reliability of mill drives and power source are important elements in the decision making process. This paper examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1991

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

By D. A. Baker, E. A. Gyawu, K. Awuah-Offei

Several underground coal mining disasters, such as Upper Big Branch in 2010, have revealed technological and organizational shortcomings related to self-escape. Efforts to address these gaps have primarily been top-down, that is, identified and implemented by upper management or external governing bodies. In contrast, this study employs a novel miner-centered approach to identify perceived technological boundaries to self-escape. Using a semi-structured, scenario-based survey, we elicit direct feedback from miners about current, emerging, and hypothetical technologies aimed at improving self-escape during mine emergencies. The results show a general high usefulness rating across all 21 technologies in the survey. Miners who work underground (both outby and working face miners) appear to give higher usefulness ratings overall than miners on the surface and other locations. This work will be directly applied to a series of proof of concept and prototype studies on self-contained self-rescuers (SCSRs), refuge alternatives (RA), and communication devises aimed at improving self-escape technologies through miner-centered research and design.

Mar 2, 2022

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019

By J. K. Whyatt

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations of in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence from the Lucky Friday Mine collected by U.S. Bureau of Mines researchers, as well as a review of case studies, demonstrates that in situ stress variations affect the spatial distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies, they are too expensive and, depending on conditions, may be too difficult, to use routinely in mapping stress variations. However, information from borehole and raisebore breakouts; deformation of mine openings; and patterns of seismicity, ground control problems, and rock burst damage can be used to build a stress database. This database can then be used in con-junction with maps of mine structure and geology and models of rock mass behavior to build a map of in situ stress variations. Such a map provides a means to anticipate patterns of mining-induced seismicity that are likely to be encountered and, hence, provide a means for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1995

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. DPM exposure is therefore regulated by the U.S. Mine Safety and Health Administration (MSHA). The current monitoring process takes days or weeks for exposure levels to be known, and a real-time monitoring device is needed. It is believed that infrared spectroscopy has potential for use in a real-time, field-portable device. This paper presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. 

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production, but the thermal state of pellets in the drying section is still unclear. In this study, the temperature distribution of the drying section was investigated using computational fluid dynamics (CFD). The results indicate there is a coupling effect in the drying section of a traveling grate. Gas with higher temperature in down-draught drying (DDD) transfers heat to the up-draught drying (UDD) through the gap of the insulation board, and the temperature gradient of the pellet bed changes before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD are displayed in UDD in advance. To verify the model, a contrast experiment was conducted.

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975