Search Documents

By W. R. Dengler

Dynatec Mining Limited contracted to sink a lS00 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.S ft.) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (l5 ft.) diameter double-drum hoist to sink the shaft with 12.S tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1992

By J. N. Murphy

The use of the National Science Teachers Association (NSTA) regional meetings as a forum to educate teachers on the role of minerals in our society has been immeasurably successful. Each year, on average about 3,500 to 4,000 teachers participate in each of the three regional NSTA meetings. At each of these meetings, nearly 2,000 teachers visit the “Minerals Coalition Booth” and receive free mineral samples and other educational support materials. Some rules of thumb for a successful booth at the NSTA are provided. Considering the level of effort for such a booth, are there alternatives? The NSTA also organizes a national annual meeting with attendance of about 20,000. All who have participated in a regional NSTA agree that the traditional approach of providing a mineral set and teacher materials for a substantial fraction of the 20,000 attendees is not feasible. Conceptual alternatives for minerals education at the national NSTA meeting are introduced and evaluated.

Jan 1, 2001

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By Steve Klein

The Transbay Downtown Extension (DTX) in San Francisco involves the construction of a large-span tunnel with a width ranging from 43 to over 60 feet. The tunnel will be excavated using the New Austrian Tunneling Method (NATM), also known as the Sequential Excavation Method (SEM), in highly fractured and sheared rock. This paper discusses the FLAC (Fast Lagrangian Analysis of Continua) analyses that were completed for conceptual design of the tunnel support system and to develop surface settlement estimates for the evaluation of measures to protect existing buildings located above the tunnel from damage.

Jan 1, 2008

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By K. Tabra

In a mine operation, the proper strategy to handle residues is one of the main concerns, in particular when dealing with mine/plant liquid effluents. Most active water treatment systems at metal mines rely on standard alkali-addition procedures. However, the increase of mineral prices, stricter environmental standards and high metal content in some effluents, has led to the development of alternative treatment techniques for their removal and/or recovery. This article presents a roadmap to face mine wastewater treatment requirement, with focus on two active treatment strategies: 1) conventional lime-based technology and 2) the use of NaSH or Fe(OH)3 for metal precipitation and separation, including possible valuable elements recovery. The Roadmap consists of 1) Approach to effluent treatment 2) Characterization 3) Precipitation tests 4) Solid/liquid separation tests and 5) Economic analysis.

Feb 27, 2013

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By C. Heath

US coal consumption reached new heights in 1985, but production was constrained by excess consumer inventories. Domestic consumption of coal reached a record 742 Mt (818 million st) during the year. This is a 3.4% gain over the previous consumption high 718 Mt (791 million st) in 1984. An additional 84 Mt (92.7 million st) of US coal were shipped abroad in 1985, up 13.7% from exports a year earlier. Coal production in 1985 totaled 804 Mt (886 million st), 1.1% below the record 813 Mt (896 million st) produced in 1984. The slight decline in coal output is attributed primarily to a 13% drawdown of large consumer stockpiles built up in 1984 in anticipation of a miners strike that never occurred. Coal demand, and hence production, were also restrained by slower economic growth in 1985 and additional gains in nuclear generation of electricity. Domestic market requirements for coal in 1985 were mixed. Electric utility consumption rose 4.4%; coke plants consumed 6.7% less coal; coal requirements in the other industrial sector expanded by 2.1% and consumption in the residential and commercial sector fell 14.8%. The 2.2% increase in electric power generation in 1985 resulted in a 4.4% rise in utility coal consumption, totaling 630 Mt (694 million st) for the year. Twenty-nine of 45 states where coal-fired electric power plants were operating shared in the 26.7 Mt (29.5 million st) increase in 1985. Coal receipts at utilities fell by 16 Mt (18 million st) as these facilities worked off 21 Mt (23.4 million st) from stockpiles during the year. Electricity generation at coal-fired power plants similarly climbed 4.4% to 1.4 trillion kWh in 1985. This gave coal a 56.8% share of electricity generated from all energy sources compared with 55.5% in 1984. The average price of coal delivered to these facilities remained essentially unchanged during the year. It declined on 1.5% from $38.26/t ($34.71 per st) during the fourth quarter of 1984 to $37.70/t ($34.20 per st) in the fourth quarter of 1985. Coal consumption at coke plants continue to reflect a depressed steel industry. After rebounding 18.9% in 1984 for the first time in five years, coal consumption at coke plants again declined 6.7% to 37 Mt (41.1 million st) in 1985. Coke consumption 26.5 Mt (29.3 million st) exceeded production, 26 Mt (28.7 million st), in 1985. This resulted in a 1-Mt (1.2-million st) decline in coke stocks at producer and distributor levels during the year. The average price of coal delivered to coke plants decreased 7.6% from $64.30/t ($58.34 per st) during the final quarter of 1984 to $59.42/t (53.91 per st) in the last quarter of 1985. Coal consumption in other industries, including all manufacturing and industrial consumers except coke plants, totaled 68.3 Mt (75.3 million st) in 1985. This was the highest level attained in more than a decade. But the lower percentage rise last year (2.1% compared to 11.8% in 1984) reflected slower growth in the nation's economy in 1985. The average price of coal delivered to industrial firms declined 4.5% from $42.32/t ($38.39 per st) in the fourth quarter of 1984 to $40.39/t ($36.65 per st) in the last quarter of 1985. Coal-producing states in Appalachia mined 9.8 Mt (10.8 million st) tons less in 1985 than in 1984 for a 2.4% loss. The largest contributors to the region's production decrease to 393 Mt (433 million st) were Pennsylvania, down 14.7% to 60 Mt (66 million st); Ohio, down 8.3% to 32.6 Mt (36 million st); and West Virginia, down 2.9% to 115 Mt (127 million st). Conversely, eastern Kentucky production was up 4.8% to 111 Mt (122.8 million st) in 1985, while production in Tennessee climbed 9.7% to 40 Mt (44 million st). No coal was mined in Georgia last year. Coal production in the interior region in 1985 declined 3.9% to 173 Mt (190.4 million st). Substantial production losses occurred in Indiana, down 8% to 31 Mt (34.5 million st); and in western Kentucky, down 7.9% to 36 Mt (40 million st). Coal production in Texas rose 5.7% to 39 Mt (43.5 million st) in 1985. Louisiana began mining lignite 140 kt (151,000 st) during the year. Production in the western region increased 3.4% to 238 Mt (262.5 million st) in 1985. Wyoming, up 5.3% to 125 Mt (140 million st); and North Dakota, up 16.5% to 23.5 Mt (26 million st) contributing the largest amounts. Production gains were also shown in Washington, Utah and, notably, in Alaska where coal output climbed 72.9% to 1.3 Mt (1.5 million st) in 1985. Most of the additional coal produced in Alaska last year was shipped abroad. Coal stocks held by consumers totaled 154 Mt (170 million st) at the end of the year. This was 27 Mt (30 million st), or 13.7% below the inventory level at the end of 1984. Stocks held by producers and distributors declined by 868 kt (957,000 st), or 2.8% in 1985 to 30 Mt (33 million st). A drawdown in stockpiles occurred in each consumer sector during 1985. Stocks held by electric utilities totaled 142 Mt (156 million st) at the year's end, 13% lower than stock levels at the end of 1984.

Jan 5, 1986

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By Mark Rybak

On Aug. 31, 2006, Tropical Storm Ernesto hit the city of Richmond, VA. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This article describes the fast track design, bidding and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft-sinking methods and final lining design all contributed to the success of this project. The storm inundated Richmond, VA with up to 305 mm (12 in.) of rain that, in some areas, caused widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed and caused local combined sewer and stormwater flooding. The collapsed sewer was a 2.4-m x 76-mm (8-ft- x 3-in.-) wide by 2.7-m- x 152-mm- (9-ft- x 6 in.-) high arch sewer that was constructed in the 1920s and later filled over with municipal solid waste and a soil fill cap to cur-rent elevations. A sinkhole was created in the area of collapse approximately 18 m (60 ft ) deep and 31 m (100 ft) in diameter. This caused the existing arch sewer to become blocked. As a result of this blockage, contaminated floodwaters reached depths in low-lying areas in excess of 8 m (25 ft).

Jan 1, 2008

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007