Search Documents

By J. Guzman

Introduction The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km' (386 sq miles) in and around the Carlin Trend and own all or part of I6out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output. The same incentives produced even more spectacular exploration results. In each of the last five years, net additions to reserves and resources outpaced current production by substantial margins. These facts demonstrate the spectacular past prospectiveness of the Carlin Trend and the success of focused, multi-disciplinary exploration methods that made it possible to more than offset the recent accelerated depletion of gold resources. However, is this situation sustainable? How long can the mining companies along the Carlin Trend keep on finding resources faster than they deplete them? These are some of the questions that motivated this study. The authors have not quantified the future potential for gold exploration in the Carlin Trend nor established a deposit discovery path. But strong indications were discovered that the [ ] Carlin Trend remains a relatively immature exploration district and that the potential for significant new discoveries is high. Methodology and data The approach chosen to address the above questions was simple. The authors compiled deposit size data, measured in contained ounces of gold resources, for all known deposits along the Carlin Trend (Table 1). The resource information was obtained by adding cumulative historical production (adjusted for mining losses and metallurgical recovery) to 1989 year-end published resource inventories. In a mature exploration area, where most deposits have been discovered, this distribution would be expected to approximate lognormality and would plot along a straight line on a lognormal probability scale. This result was found in previous work by Allais (1957) and recently confirmed by Cox and Singer (USGS, 1986) in regard to various types of mineral deposits in several regions of the world. It was also found to hold true for oil and gas pool size distributions (Arps and Roberts, 1958; Kaufman, 1962; McCrossan, 1969). [ ] The data used were compiled by Newmont Exploration geologists. The purpose of the study is to make inferences about the underlying geologic processes in the district and the maturity of the exploration effort. Therefore, deposits were not classified according to ownership but according to geologic occurrence as known from current information. Newmont's Post and Barrick's Goldstrike and Betze deposits, for example, are shown as a single occurrence to reflect the actual geologic setting. The cumulative frequency distribution of deposit sizes was plotted on lognormal probability paper (Fig. 2). The abscissa shows the cumulative fraction of deposits at or below a certain deposit size and the ordinate shows the deposit size in thousands of ounces of contained gold resources.

Jan 1, 1992

By Bob Snashall

"We could blow that damned fort out of existence if we could run a mine shaft under it!," claimed one Union soldier eyeing Bobby Lee's Petersburg defense line protecting Richmond and Jeff Davis. Puncture the line, take the hill behind, and the Confederate capital would celebrate Yankee jubilee, 1864. That was June. At 4:15 am, July 30, mine boss Henry Reese, sergeant, 48th Regiment, Pennsylvania Volunteers, gingerly entered the mine, dark and muddy. Something had gone wrong. The mine, set to go off at 3:30, hadn't exploded. It had to be checked. The main mine gallery, 1.5 m high x 1.4 m wide (5 x 4 ft) narrowing at the top to 0.6 m (2 ft), forced Reese into a tuck run. Some¬where up there in that 155 m (511 ft) stretch running 6 m (20 ft) under the rebel works, moisture may have doused the charge. Or maybe a fuse splice went awry. Or maybe there was live fire steaming like a locomo¬tive towards 3.6 t (4 st) of black powder. Perhaps now Reese wished this sprint was shorter. For the mine boasted a record break¬ing distance in military annals. Lieut. Col. Henry Pleasants Credit goes to Lieut. Col. Henry Pleas¬ants, commander of the 48th, who overheard the soldier's claim for what a mine could do. In peacetime, Pleasants had been a railroad engineer working on the Sand Patch Tunnel. He later switched to mining, working for the Philadelphia & Reading Coal & Iron Co. He even married the daughter of the editor of The Miners Journal. Grieving over his wife's early death, Pleasants plunged into the ven¬ture of war. This Union officer took the mine idea to the brass. Headquarters was less than enthu¬siastic. "The chief engineer of the Army and the rest of the regular Army wiseacres said it was not feasible," Pleasants wrote to his uncle. The pros scoffed, ticking off a list of horribles: No mine has ever gone that far, men will suffocate and be crushed, the rebs will countermine, the men will be trapped. Still, Pleasants eked out a signal to proceed. In the meantime, the miners of the 48th had commenced to dig anyway. It was like the 48th to proceed against the odds. The 48th Pennsylvania Volunteers The 48th had been recruited from Penn¬sylvania's Schuylkill County, anthracite coal mining country. The mines had been torn with strife over wages. Strikes and rioting were prevalent. Murder was not unknown. This "Buckshot" resistance centered in Pottsville, PA. It forced the governor to call in troops. Coal was in high demand to run the war machine. Pennsylvania operators worried that a military draft would stir up violence, closing the mines altogether and further shift¬ing business to emerging Illinois mines. Men lit out for the western gold fields in the tens of thousands. Secret societies bred in the mining camps invited draft agents to dance at the end of a rope. Jobs threatened by cheap, victorious South¬ern labor were one warning intended to get immigrant miners interested in the war. Operators gave miners time off to help de¬fend Philadelphia during Lee's thrust to Gettysburg. Even so, the draft spawned new violence and troop intercession. Soldiers were not welcome. The dust had barely settled when into this Pennsylvania "minefield" marched the 48th on a recruitment drive. The 48th had been in Lexington, KY on guard duty. When it came time for the regiment to pull out, the townspeople had prevailed upon authorities to extend the regiment's stay. Finally ordered to move out, the 48th was feted by a hanky-waving, tear-dropping send-off to the lyrical lament Auld Lang Syne. And Kentucky fancied itself to be rebel. Striding smartly into the Pennsylvania coalfields, the 48th attracted 400 recruits and marched off under regimental colors specially made by the proud citizens of none other than Pottsville, PA.

Jan 1, 1989

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985

By Earl M. Frizzell, Ronald W. Utley

Introduction For the past several years the Bureau of Mines has undertaken research to develop alternative mine material haulage systems that will improve mine productivity, reduce haulage costs, increase mineral availability, and conserve energy. One basic concept being pursued is a means for crushing primary blasted rock to a size that can be reliably and economically moved on conveyors. During 1980, mine requirements for this equipment and the capability of existing technology to satisfy these requirements were assessed. The study continued into 1981 on the basis that satisfactory equipment for this purpose needed to be developed. The objective of the 1981 program was to perform an engineering design of such a system. A mine survey and equipment development study was conducted in cooperation with the open-pit mining industry by GATX through its subsidiaries, Fuller Co. (a crusher manufacturer) and GARD Inc. (GATX's research and development center), under contract to the USBM. Results of a mine survey in the copper, iron, and molybdenum industries indicated that a universal crusher system could be developed even though details might vary from mine to mine. The crushing characteristics, including tonnages desired, were similar in all surveyed mines. Most mines had similar views about the desirability and frequency of crusher movement. The perceived need for in-nit crushing varied between copper and iron mining. The copper mines felt a greater sense of urgency for introduction of such a system, probably because typically greater vertical haulage is found in copper mines than in the iron mines. All mine personnel surveyed were interested in portable crushers and almost universally preferred gyratory-type primary crushers. They preferred large crushers, citing inherent reliability and durability, and the machine's relative freedom from clogging. Large size minimizes the number of crushers and conveyors needed. Analysis of desired crusher system characteristics (Table 1) fixed the crusher size at 1.5 x 2.3 m (60 x 89 in.). The 1.5-m (60-in.) feed-opening dimension could accept the largest material normally fed to the crusher, and the 2.3-m (894n.) head diameter could fulfill the 3.63 kt/h (4,000 stph) capacity requirement. Selected System Description The comments and analyses discussed in the contract report led to the design and refinement of a movable crusher system. This system represents the consensus of more than 100 mine workers and almost 50 construction and engineering company personnel. It is supported by more than 50 years of experience in crusher manufacturing. Although many alternatives are available for any given system, and selections are likely to be dictated by varying site conditions, the selected system is believed to be appropriate for most projected requirements. Final design would be dictated by mine operators during evaluation for approved projects. Detail design of the feed and discharge systems were not included in the study because they are mine specific. The basic system (Fig. 1) consists of a 1.5 x 2.3-m (60 x 89-in.) gyratory crusher on a structural steel frame. The frame is used as an operating platform for the crusher and as a carriage to move the crusher. The control tower includes a crusher lubrication room, a hydraulic equipment room, a switch gear room, a room for the motor control center, and a control room for operating the crusher and maintaining the equipment. The auxiliary system consists of a hydraulic rock hammer and pedestal crane with 74-t (80-st) and 14-t (15-st) hooks. Figure 1 also shows stairs, railings, and a work platform. Feed and discharge arrangements are shown on Fig. 2. The system shown is for mildclimate applications. Additional enclosure and heating would be needed for extremely cold weather conditions. Crusher A 1.5 x 2.3-m (60 x 89-in.) gyra¬tory crusher was selected for this application. This size can handle the typical throughput of 3-3.63 kt/h (3,500-4,000 stph) desired by the mines and the 1.3-m (50-in.) material to be crushed without difficulty. The crusher is the heaviest

Jan 4, 1983

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

By Otto Schumacher

Shortcut methods are commonly employed for estimating mining costs for prefeasibility studies. Most of these methods, however, are suitable for earliest stage studies or for internal discussion purposes only. The experts at InfoMine?s CostMine division recommend that any cost estimate completed for purposes of significant decisionmaking or for compliance with Canada?s NI 43-101 requirements be completed using a determinative itemized method. The same basic principles apply for an early stage, intermediate stage, or advanced stage estimate. The only difference is in the level of detail and effort employed. ? Based on the results of a completed resource estimate, an itemized cost estimate begins with development of a conceptual mine plan. Using a surface mine as an example, four elements are crucial no matter what level of study is initiated. Basic geometry of the ore deposit and waste material, with a determination of the expected ratio of waste to ore, a reasonable pit slope angle, possibly requiring the completion of geotechnical studies to predict the waste-to-ore ratio with certainty. ? Determination of the assumed ore and waste production rates. ? Locations of all ore stockpiles and waste dumps. ? Segmental haulage distances and gradients for ore and waste.

Oct 1, 2013

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Oren Tranbarger

The ability to sense or detect the coal/non-coal interface during mining can provide numerous advantages for improving net coal recovery and quality, for increasing productivity, and for mining coal which would otherwise be ignored. This is particularly true when considering multiple, pitching, and thin coal seams. This paper discusses the application of coal interface sensing and examines several potential coal interface sensing techniques with respect to state-of- the-art, design, performance, and cost criteria. Four interface boundaries are considered: the roof, the floor, the rib, and the forward region.

Jan 1, 1982

By VIVEK KUMAR HIMANSHU, PK SINGH, AK MISHRA, MP ROY, RAVI SHANKAR

Underground blasting has many challenges. The primary aim of blast designers is to optimize drilling and blasting parameters to deal with the associated challenges. Optimizing these parameters is currently based on various rules of thumb, which have many site-specific limitations. Accordingly, computation of these parameters using empirical rock fragmentation predictors can be useful for blast designers. This paper presents the results of work on burden-spacing determination by back-calculation from the empirical Kuz-Ram model for underground stope ring blasting.

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By Dru Brown

More than 150 Mt (165 million st) of material crashed down at the Bingham Canyon Mine (Rio Tinto/Kennecott Utah Copper) near Salt Lake City, UT on April 10, 2013. The mine, one of the largest openpit mines in the world, ceased operations and evacuated personnel prior to the slide when it was discovered that material was moving at a rate of 5 cm/d (2 in./day). The slide destroyed the mine?s visitor?s center, buried several pieces of large mining equipment and severely hampered production. The Kennecott Utah Copper Corp. immediately began to assess the damage and look for options to reestablish operations. The highly unstable ground ? emphasized by another minor slide in September 2013 ? makes any cleanup efforts extremely dangerous. With terrain too dangerous for human operators, Kennecott was forced to look for alternatives that would help the company work on the treacherous slopes of the landslide while also keeping personnel safe.

Jan 1, 2014

"With millions of dollars and thousands of lives at stake, the Iron Ore Company of Canada (IOC) turned to a private wireless network for help.IOC needed a network that possessed the ability to adapt to changes in a nanosecond and to function seamlessly in the most rugged of environments.Canada’s largest iron ore producer required a private wireless network powerful enough to support all mine applications and deliver all data to one central point — without any existing cellular/3G/Wi-Fi coverage.Operations at IOC, a leading global supplier of iron pellets, involved dispatch, drill management and equipment monitoring, pump control and remote video that must service three distinct pits. Due to its setup, the facility does not offer a great deal of flexibility for transmitting signals.IOC serves a robust customer base made up of North American, European and Asian steel producers. It also employs nearly 1,900 people. Catastrophic death and destruction are two very real potential consequences of system communication failure.Technology for tough terrainKinetic mesh technology was born in the wake of the 9/11 terrorist attacks on the United States, one of the most high-stakes emergency situations in U.S. history. The failure of the communications infrastructure on a massive scale that day underscored the need for networking technologies that could provide service even in the most chaotic of conditions.Kinetic mesh networks allow organizations to deploy networks at sites where communications infrastructure has been compromised, as well as quickly establish networks in places where they did not previously exist. Kinetic mesh networks have also demonstrated a better ability to adapt to network changes on-the-fly versus other types of networking technologies."

Jan 1, 2015

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By Ankit Jha, Javad Sattarvand, Aaron Young

Blockchain technology is one of the prominent disruptive technologies that are being implemented in several disciplines. The application of blockchains in the mining and mineral industry can provide utility to several processes especially when the industry is undertaking digital transformation. The governing principles of blockchain technology are applicable in undertaking transformation in several processes within the mining industry. This study investigates the applications of blockchain technology within the realms of the mining industry and identifies key areas of implementation. A systematic review of publications on academic platforms relating to blockchain technology in the mining industry did not retrieve a considerable number of articles. Consequently, a thorough review of white papers and articles authored by individuals on use cases within the mining industry is compiled and presented in this review article. This review article identifies all the potential areas within the mining industry where blockchains could provide value and improve processes through their implementation. The broad area of implementation of blockchains includes supply chain, traceability in spares parts, contract management, regulatory compliance and cybersecurity.

Mar 1, 2024

By Shamim A. Dar, Mohd Shuaib, K. F. Khan, Samsuddin Khan

Petromineralogical studies of late Paleocene–middle Eocene phosphate nodules in the Subathu Basin of Solan District, Himachal Pradesh

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the results of a study on the optimum auxiliary fan location to control air recirculation in dead-end workings where diesel-powered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut and with the intake air quantities varied using different auxiliary fans to control air recirculation and diesel particulate matter (DPM).

Jul 1, 2023