Search Documents

By Sushil Bhandari

A computer model is developed for the problem of dispersal of dust (suspended particulate matter) resulting from blasting operations in surface mines. Undulated surface (lower boundary) simulation was carried through sixth order polynomial by least square approximation. Segmentwise terrain simulation was linearly added to build ground feature extending either side of the blast location. Assuming the initial dust concentration in the vertical column to. be uniform and treating the finite vertical line sources as a series of point sources to height, H varying from zero to top of the dust mushroom, integration was done of the concentration effects from H = 0 toL tan[0] (L = horizontal distance of the blast location and [0] is the angle of the top of dust cloud from the point of observation). Using frame of reference moving with the mean wind, the ground level 'concentration (GLC) has been computed over the undulated terrain. Standard deviation (s) of concentration has been parameterized based on mixed layer similarity theory in convective boundary layer.

Jan 1, 2002

By Jim Morris, Davin Ishii

The major source of water for Southern Nevada is Lake Mead. However, the existing pump station located on Lake Mead is inadequate for one of the fastest growing areas in the United States. In order to keep up with the increasing demand for water in Las Vegas, a parallel system is being constructed. The intake for this system is being constructed approximately 68.58m (225ft) below the surface of Lake Mead. The lake tap consists of installing casing and secant piles to support the shaft collar, excavating a 21.34m (70ft) deep intake shaft, and installing a3.66m (12ft) diameter steel liner.

Jan 1, 1999

By Karl J. Ellefsen

A geophysical investigation can provide valuable geologic information needed to characterize sand-and- gravel deposits and can be an attractive complement to more common characterization methods such as drilling. Although such investigations have been conducted already, a comparison of the different geophysical methods used in these investigations apparently has never been done. For this reason, a study was initiated by the Mineral Resources Program of the U.S. Geological Survey to determine the advantages and the limitations of different geophysical methods when used to evaluate alluvial sand-and-gravel deposits. The study is focused on those geophysical methods that are commonly available, because these are most likely to be used by industry. Furthermore, the study is focused on surface geophysical methods. Heretofore, four different methods have been evaluated. Three of the four methods-time-domain electro-magnetic (TEM) soundings, frequency-domain electro-magnetic profiling, DC-resistivity soundings-are similar in that they all measure the electrical resistivity of the ground with depth. Ground-penetrating radar, however, maps changes in the dielectric permittivity and for the electrical resistivity with depth. For all, four methods, the objective is to relate the measured physical quantity to the stratigraphy of the alluvial sediments.

Jan 1, 1999

By A. Exikis

Simulating a ventilation network of an underground mine can help in solving complex ventilation systems with many features, selecting proper fan specifications, location and settings. Early computer systems running simple network simulations were able to provide solutions to the most common and immediate problems regarding underground mine airflow. The more advanced systems available today can perform more sophisticated modeling and simulation of a mine?s ventilation network and present their results in a more understandable and easy to communicate form. This paper presents a ventilation network case study from an underground mine. All aspects of mine ventilation network modeling and simulation are discussed as well as the results from the simulation process. The algorithms and techniques used are thoroughly explained. Some useful guidelines for the application of ventilation network software are also provided in the text.

Jan 1, 2006

By Betty L. Gibbs

A clear and accurate knowledge of the status of ventilation in an underground mine is essential to continuing safe operation. In a small mine with a few working faces, the problem is simple and can easily be solved by choosing the appropriate fan. In larger, more complex mines the problem of supplying the working faces with fresh air is a problem beyond the scope of 'finger in the wind' analysis. In today's climate of stiffer government regulation and mining company concern for the safety of workers, computer programs which analyze ventilation networks are helping mining companies meet the standards. The development of computer programs for ventilation network analysis is summarized. Early programs were developed at universities or government agencies and required large expensive computers. As computers have become smaller and less expensive, the development or revision of programs for micro computers has become more available. Prices have lowered to the point of affordability even for medium and small companies. A list of ventilation network analysis programs is provided along with a summary of capabilities, costs, and hardware requirements for each program.

Jan 1, 1987

By H. E. M. N. Moursy, Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, D. Chandler, G. Walker, Regis Stana, Patrick Zhang

The reaction kinetics of the acidulation of Moroccan phosphate rock (32% P?05) using 45% nitric acid were investigated using the Shrinking Core Model (SCM) , a newly developed Diffusion Model (DM) and a newly developed Combined Reaction and Diffusion Model (CRDM). This was achieved buy conducting a number of experiments in a controlled batch reactor system at different temperatures. The conversion and the reaction rate were calculated at different time intervals. The SCM based on reaction time and the CRDM characterize the acidulation process of phosphate rock. Diffusion of nitric acid and the products of acidulation at the early stages of reaction through the phosphate rock were found to be the rate-controlling step, resulting in a dif- fusion coefficient, which controls the mass transfer process. The reaction kinetics were found to fit first-order kinetics especially during early stages of reaction time. The deviation of the kinetics from first-order at later stages was due to the fact that the overall reaction was mass transfer controlled with respect to nitric acid and products diffusion.

Jan 1, 2002

By I. Dumitrescu

Since 1990, the entire Romanian mining industry has suffered a major restructuring, i.e. technical and economic. The large majority of the remaining active mines are these with a chance for economic comeback. This is also the case for the mines that belong to MINVEST Deva Company; most of the mines are closed, and are waiting to be reclaimed. The authors present the closing procedures of the former copper mining perimeters managed by MINVEST. It is well known that pollutants of concern for the environment must be monitored to obtain reliable information on the quality of ambient conditions and to minimize their impact on the environment. Consequently, the monitoring problems during the closing procedures will be presented.

Jan 1, 2008

By A. L. DeVegt, H. G. Bayer, C. J. Buisman

During the last ten years, Paques Inc. has been engaged in the development and installation of treatment systems to remove sulfur compounds from water and gaseous streams using biotechnological processes. Metal and sulfate can be removed from mine waters in two biological steps. In the first step, sulfate-reducing bacteria converts sulfate to hydrogen sulfide (H2S). The HS reacts with the dissolved metals to form insoluble metal sulfide precipitates. In the second step, sulfide-oxidizing bacteria convert excess H2S to elemental sulfur. The Budelco Zinc Refinery in The Netherlands installed a groundwater treatment system to remove metals and sulfate using the biological steps described above. The system has been operating since May 1992 and has been treating 5,000 m3/d (180 thousand cu ft/day). A pilot plant began operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop processes for metal and sulfate removal from groundwater and for the selective copper recovery from leach water. The principle of the biotechnological methods, the full-scale experience and an overview of the test program at the mine are presented

Jan 1, 1999

By Jan W. Oberholzer, Jan J. L. Du Plessis, Gerard Appelman, Andrzej M. Wala

The use of on-board scrubbers on continuous miners is an important aspect in efforts to reduce the amount of dust that heading workers are exposed to. As part of the CSIR:Mining Technology's research programme to combat dust, a collaborative project with the University of Pretoria was conducted to evaluate scrubbers. Based on fundamental parameters that were identified to play a role in determining the efficiency of scrubbers, a protocol for testing scrubbers in the laboratory environment, as well as the working section, was established. Tests on various prototype scrubbers were conducted in the laboratory environment. These tests proved some of the fundamental premises according to which scrubbers were designed. By testing some of the newer scrubber types underground, insight into the effect of alternative design aspects on scrubber efficiencies was obtained. The importance of the factors which play a role in reducing the amount of dust in the air is illustrated, as well as the role which other non-design factors play in the reduction of dust levels.

Jan 1, 1995

By R. Debkowski

Mining methods used to protect the workings in underground salt mines against the destructive activity of natural factors are presented in this paper. Major hazards and methods of elimination of their impact on the stability of workings, were determined. Old and modern technical means and technologies used for protection and preservation of the selected most interesting sites were characterized. The results of surveys and studies allowed proposing the change of mine structure i.e. dividing it into monumental and not-monumental part, which should improve execution of necessary protective works.

Jan 1, 2006

By Greg Adel, Darren Thornton, Julius Krutschnitt, Toni Kojovic, J. Mark Richardson, Bryan Smith

Mine-to-Mill® optimization is a total systems approach to the reduction of energy and cost in mining and mineral processing operations. Developed at the Julius Krutschnitt Mineral Research Centre in Queensland, Australia, it attempts to minimize energy consumption through the optimization of all steps in the size reduction process. The approach involves sampling and modeling of blasting and processing, followed by computer simulation to optimize the operation and develop alternatives. The most promising alternatives are implemented, and sampling is conducted to quantify energy savings. In the current DOE-sponsored research project, the primary objective is to adapt the Mine-to-Mill® technology to the aggregates industry. The project is being carried out at two quarries operated by Luck Stone of Richmond, Virginia. This paper presents work conducted at the Bealeton quarry.

Jan 1, 2005

By Shouci Lu, Keji Sun, Dianzuo Wang, Yiqun Li, Chuang Jin

The dephosphorization of iron ore and reduction in Fe loss in process are currently the foremost technological challenges facing the mineral industry of Meishan Iron Ore. These problems can be resolved to a greater extent by an apatite flotation process which depends on selective flotation reagents. The primary objective of this research work is to develop new type of flotation collectors for dephosphorization of weak magnetic iron ore. Detailed discussion is given on the influence of collector dosage, pH, dispersants and pulp temperature on the flotability of apatite, siderite and hematite using the collectors of Oleyl sarcosinate(OSS), Alkyl polyoxyethylene ether phosphate (AEP) and the mixtures of OSS and AEP A key feature of the flotation was the use of the mixtures of OSS and AEP as a selective collector for phosphate. The effects of chemicals and operational variables on the phosphorus flotation from the weak magnetic iron ores have been investigated. The test results shows that floating the phosphorus minerals with new type collectors can reduce the phosphorous content in the flotation concentrate to an acceptable level of less than 0.20% P with increased Fe recovery.

Jan 1, 2002

By R. R. Klimpel

In three recent publications, Klimpel et al (1988) and Klimpel and Hansen (1988, 89), the theory and invention process behind the identification of two new classes of sulfide mineral collectors were summarized. These two new families can be represented by the 111 generalized formulate: R1-S-R1 -NRI III (denoted as the F-series chelation family) and R-S-R or R -CHSCH-R (denoted as the S-series redox family). The influence of systematic changes in the various R groupings on laboratory batch flotation cell tests has been covered in the above references and will not be repeated in this paper. In particular, the recent article by Klimpel and Hansen (1989) should be studied as a research introduction to this paper.

Jan 1, 1989

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By Donald E. Ranta

Many portions of the mining industry are under intense pressure to reduce costs while commodity prices languish. In response, global Internet-based marketplaces to deliver business-to-business (B2B) e-commerce solutions are being established to reduce costs and improve efficiencies across the mining industry supply chain as well as with customers. Over time these marketplaces will likely evolve to create an integrated supply chain solution, layer in value-added services, and develop mining community portals with industry content. Significant opportunities to help reduce costs and create value are available in mining e-procurement as well as in on-line product sales. The supply chain for the industry is highly fragmented and many mining companies have numerous inefficiencies in procurement. An e-procurement marketplace (or "exchange") can immediately address these inefficiencies and offer numerous benefits to buyers and suppliers. These benefits include improved sourcing options, inventory cost reduction, transaction cost reduction, access to value-added services, lower customer and supplier acquisition costs, improved reach, and improved information flows.

Jan 1, 2001

By J. M. Dean, R. L. Grayson, R. D. Begley, G. L. Winn

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1998

By Victor Rudenno

Cut-off grade is one of the most critical parameters affecting project cash flow. Its sensitivity is due to the number of other parameters that are correlated with any change in its value. Changes in cut-off grade, average grade and ore tonnage vary and they in turn can affect such parameters as capital and replacement costs, recovery, life of the project and operating costs. Perhaps one of the best definitions of cut-off grade is that of Taylor (1), "... any grade that, for any specific reason, is used to separate two courses of action, e.g. to mine or to leave, to mill or to dump ... . Obviously the most likely specific reason is one governed by economics, involving the return of investment and sufficient profit to motivate development and mining of the deposit. In this paper the cut-off grade is defined as that mining limit which will maximise the economic return for a projected mining venture. The following brief literature survey indicates that when computing the optimum cut-off grade there is a need to be able to directly compute the Discounted Cash Flow Rate of Return (DCFRR) or Net Present Value (NPV), as economically as possible, while allowing for parameter dependencies and variation in project structure.

Jan 1, 1979

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986

By J. A. Herbst, J. E. Bohrer, Y. C. Lo

A systematic approach has been developed to analyze a phosphate grinding circuit with a view toward determining promising alternatives for increasing mill capacity. This analysis was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills and classifier systems. Model development and verification was performed using data obtained in a series of batch tests and two plant test campaigns. The effects of feed rate, percent solids, ball size, and mill material filling, etc., on grinding were investigated in the laboratory and plant. Residence time distribution tests were also performed to determine the transport behavior in the mill. The population balance models were found to provide accurate predictions of full-scale grinding circuit performance. Based on the findings of this study, additional capacity in excess of 25% was predicted for these ball milling circuits by a proper combination of ball size change, mill dilution, and adopting screen classification in place of hydro-cyclones. These predictions have been confirmed by plant tests in which the recommended operating changes have been implemented. Understanding the effects of operating variables on breakage kinetics and the interplay between kinetics, transport, and classification has contributed significantly to increasing the mill capacity.

Jan 1, 1988