Search Documents

By R. B. Lawrie

Diesel powered underground mining equipment is presently the most productive, safest and efficient equipment used in underground mining operations. The widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel missions with particulate traps and filters.

Jan 1, 1985

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU'S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964

By-products are of greater importance in lead and zinc mining than in any of the other major base metals. While I think most mining people would accept that statement, you would probably get some widely varying estimates when attempting to quantify the value of by-products in lead and zinc mining. We are now able to do this with our lead-zinc mine cost model. This model was originally developed as a zinc mine cost model to help us forecast long-term zinc supply and price as part of a study we completed in late 1979 entitled "Zinc - The Next Decade". Before demonstrating the importance of by-product revenue to lead- zinc mines, let me first explain how the cost model was constructed. I will discuss the model as it was originally constructed - as a zinc mine cost model. It has subsequently been expanded to include lead only mines and now can Be run either as a zinc or a lead mine cost model.

Jan 1, 1980

By Ed L. Schrader

Kaolin of the Georgia-south Carolina "Clay Belt" are used in a wide variety of filler and extender applications. Sane applications specifically require the performance enhancement delivered by incorporating kaolin into the product formulations. Other applications are less specific in requirements for an inert mineral filler. In order to be a feasible candidate for filling and extending, a mineral or mineral product must be generally inert (except where specific interaction with the filled medium is desired), inexpensive, easily handled and transported in a variety of forms, accessible to a broad segment of the desired market, and must exist in sufficiently large ore reserves as to assure production for many years. Of course, more precise requirements are necessary in specific applications of a prospective filler material.

Jan 1, 1985

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors: (1) sample collection and preparation, (2) counting techniques, and (3) operational definitions of asbestos in use. Three different definitions have been used in the study of environmental samples and are summarized in Table 1. The analytical procedure and detail required in the analysis vary with the definition of asbestos. Accordingly, this may be the only type of environmental analysis where the definition of a substance dictates the choice of analytical methods, and the rigor demanded of the analysis. Lead, arsenic, or beryllium are sub- stances having a constant definition and the method of analysis chosen depends on the concentration and precision required. However, the meaning of the term asbestos fiber is dependent on the eye of the beholder. Macroscopically, asbestos has certain physical properties that make it highly useful. Rockforming minerals do not display similar characteristics. Now, the question arises as to how three definitions of asbestos came into being. This is a result of two factors: (1) the definition of asbestos on any scale intrinsically involves the morphology or shape of the material, and (2) the advent of the transmission electron microscope permits detection of asbestos fibers and other mineral fragments in a size range where the physical properties of asbestos such as tensile strength, flexibility, or thermal resistance are difficult, if not impossible, to measure. There is a good deal of controversy about which definition is most appropriate for regulatory purposes because of a lack of appropriate health effects data (Cooper, 1978). Most differences of opinion center on the questions surrounding the following: 11 Morphology-Is a 3:l aspect ratio an appropriate medical or physical lower limit for the definition of an asbestos fiber? 2) Length-Are asbestos fibers shorter than some arbitrary length (5 pm) as hazardous as longer fibers? 3) Mineralogy-Is the mineralogical distinction between asbestos and nonasbestos minerals medically significant? While these questions are directly resolvable only with the biological and health effects data, ultimately such data reflects the ability of analytical procedures to fully characterize the materials used in health effects studies on animal models, and to monitor the exposure to particulates with different physical attributes in the workplace or community (Cooper, 1978). The following sections outline the analytical problems involved in distinguishing the asbestos and nonasbestos varieties of the same mineral; the analytical procedures available for identifying asbestos and measuring its concentration in environmental samples; the ability of these methods to distinguish asbestos fibers from nonasbestos particles; and their precision and reproducibility. Finally, we suggest some future directions in terms of definition and procedure that would greatly improve the quality of such analyses. ASBESTOS VS. NONASBESTOS Asbestos that is mined commercially belongs to two mineral families; amphibole and serpentine (Zoltai, 1978, Wylie, and Steel, 1978). The

Jan 1, 1986

By T. Yukimasa

Hachinohe smelter, a zinc-lead blast furnace complex with the annual capacity of zinc plus lead of 100,000 tons, had originally treated normal zinc and lead sulfide concentrates. However, it is currently handling a great variety of raw feeds ranging from complex sulfides to oxidic recycled materials in view of resource economy, most of which are unsuitable for zinc electrolysis. This paper reports on some significant efforts recently carried out on improving sintering operation, i.e., the increasing use of secondaries against harmful ingredients like halogens, and the substantial reduction in energy use as the results of various modifications and improvements.

Jan 1, 1982

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980

By H. Huang, R. N. Gow

"Previously, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. Diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals (tennantite, sinnerite, and lautite) and compared to enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. INTRODUCTION A comprehensive thermodynamic review has recently been conducted on the aqueous copper-arsenic-sulfur system (Gow et al., 2014a-d). The free energies of over 100 species were collected from various authors and thermodynamic databases to produce mass-balanced EH-pH diagrams, using the thermodynamic equilibrium calculation software, STABCAL (Huang, 2014). The full database was listed and discussed by Gow et al. (2014A). Resulting diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2014a), acid conditions (Gow et al., 2014b), and alkaline sulfide leaching conditions (Gow et al., 2014c). In this study, additional mass-balanced EH-pH diagrams are generated by changing the copper-arsenic-sulfur stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species are shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions, and sulfur oxidation states."

Jan 1, 2015

By Jessica M. Wempen

"Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has application for monitoring subsidence with high resolution over short periods. DInSAR uses radar images to measure centimeter-level surface displacements. In the images, ground resolution can be relatively high, with each data point (pixel) representing the average displacement over an area of several square meters. The image data are acquired regularly which allows subsidence to be monitored sequentially over short periods; imaging periods typically range from weeks to months.Monitoring subsidence over short periods with high spatial resolution has potential to provide insight into the dynamics of subsidence and into relationships between mine advance and subsidence. In this study, for three longwall mines in the western United States, initial subsidence occurring at the start of longwall advance is quantified over short periods (12 to 72 days). C-band interferometric wide swath Synthetic Aperture Radar (SAR) images from the Sentinel satellites are used to quantify the subsidence. Overall, the data show initial development of subsidence, expansion of the subsidence trough, and the advance of subsidence in the direction of mining.INTRODUCTIONApplied Differential Interferometric Synthetic Aperture Radar (DInSAR)Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique that can be used to quantify small displacements of the Earth’s surface. Using data from the Seasat satellite, which was launched in 1978 (Jet Propulsion Laboratory, 2018), studies by Goldstein, Zebker, and Werner (1988) and by Gabriel, Goldstein, and Zebker (1989) applied Synthetic Aperture Radar (SAR) interferometry to topographic mapping and displacement monitoring. These studies established the potential for broader applications of radar interferometry. Studies by Foxall, Sweeney, and Walter (1998), Wright and Stow (1999), and Carnec and Delacourt (2000) represent some of the earliest evaluations of DInSAR for mine subsidence monitoring. All three of the studies demonstrated the application of DInSAR for quantifying mine subsidence. They also demonstrated difficulty accurately measuring subsidence over long periods due to data decorrelation. DInSAR continues to be evaluated as a tool to quantify surface deformation related to active and historic mining. For example, see Vervoort and Declercq (2018), Wempen and McCarter (2017a), Chen et al. (2013), and Liu et al. (2013). Technologies associated with SAR interferometry continue to develop. Recently launched satellites have relatively high spatial and temporal resolutions, and data processing methods and data accessibility are improving."

Jan 1, 2019

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electric field (E-field) sensing to send text based communications using two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multi-site evaluation of available TTE systems in an effort to determine their operational sensitivity. INTRODUCTION Wireless, Through-the-Earth (TTE) communication technology is designed to achieve point to point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. This ability allows TTE communication to function without the need for intermediary communications infrastructure, such as repeaters. As a result, such communication systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers 1924; Pittman, Church and McLendon 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker 2006; Wadley 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer 1973; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Jakosky and Zellers 1924; Large, Ball and Farstad 1973). Although commercially developed TTE systems have demonstrated the ability to communicate through a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker 2006; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Ilsley, Freeman and Zellers 1928; Jakosky and Zellers 1924; Yenchek et al. 2012)."

Jan 1, 2016

By Jürg Künzle

The use of the underground space has been a recurring issue in human history, whereas the reasons for building subsurface structures have changed over time. In the decades to come, the world will be marked by a variety of underground projects never before seen. This paper describes a series of characteristic challenges of designing and building underground freight transportation systems, with reference to the example of Cargo sous terrain, a privately funded underground logistics project in Switzerland. It provides an overview of contracting practices that allow these challenges to be addressed with success.

Jun 13, 2021

By David Hatem, Paul Madsen, Daniel Adams, James Morrison, Randall Essex

Managing commercial risks associated with subsurface construction may be the greatest challenge the underground industry faces. The Geotechnical Baseline Report (GBR) was developed in the U.S. to help manage those commercial risks, and to stem increasing litigation in the industry. A guidelines document by the American Society of Civil Engineers was published in 1997 and was updated in 2007. This paper provides an historical perspective, overviews the main objectives of a GBR, presents issues and trends that instigated the need to update the 2007 publication, and describes the process that will lead to a new GBR guidelines publication in 2022

Dec 1, 2022

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By Craig Allan

Underground construction environments, especially those with limited airflow such as shafts, cross passages, and stations, necessitate effective dust control. This requires combining existing measures with adapted approaches for more efficient and productive operations, cleaner jobsites, and decreased worker exposure to contaminated air. This paper will discuss new configurations and trends in dust collection on Australasian infrastructure projects including WestConnex, Melbourne Metro Tunnel and City Rail Link, all of which have applied innovative methodologies for mobile at-source dust collection. Mobile dust collectors can be track-mounted dust collectors operate alongside equipment, use hydraulic stepping systems to advance with roadheaders, or compact castor-mounted units are used within cross passage confines.

Dec 1, 2022

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022