Search Documents

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores' as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By John J. Friel

The addition of dolomite to iron ore pellets improves their high-temperature reduction properties primarily by increasing their reducibility and raising their softening temperature. In this study we prepared dolomite-fluxed pellets from three different concentrates; Hibbing, a magnetic taconite, Knob Lake, an earthy hematite; and Carol Lake, a mixture of specular hematite with magnetite. The composition n of the concentrates is given in Table I. The pellets were subjected to standard physical tests and the following reduction tests: low temperature degradation, swelling, softening, and thermogravimetric analysis. Petrographic examination and electron microprobe analysis allowed us to evaluate the effect of composition and firing on the phase assemblage. Further, we were able to interpret the test results in terms of chemistry and microstructure. This approach enabled us to determine which fluxed composition best suited each of the concentrates.

Jan 1, 1980

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today's market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By John A. Patterson

There are certain data handling techniques used by statisticans that can help one to calculate the size of an orebody and to develop some of the relationships between size, cutoff grade, average grade, mining cost, and profit. Knowing the relationships amongst these factors can help determine the most desirable operating conditions. A statistical technique that we will use is data grouping. This allows us to work with relatively few groups instead of many samples, If we were able to segregate the ore in an orebody into grade groups, add the amounts in each group, and plot the sums as a curve, we would get something like Figure 1. A smooth curve develops when the grade classes are small enough, otherwise a "stair step? histogram results. The area under the curve, being the sum of the tonnages in all of the grade classes, is proportional to the total number of tons in the orebody. If we take the data of a distribution such as Figure 1 and add the tonnages above a specific grade we have in effect a cutoff grade

Jan 1, 1958

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By Paul A. Gerding

PURPOSE: Presentation to Society of Mining Engineers, Technical Session, Wednesday, February 19, 1958 - 2:00 P.M. General Industral Minerals - Penn Top South The silica industry is relatively small and in general is made up of small plants located near the consumer. In the United States there are approximately 155 established operating plants located in 37 states, extending from coast to coast. Silica, in varying degrees of chemical purity, enjoys a very diversified market. Silica is the basic ingredient of glass, bothcontainer and flat glass, and is used for grinding and polishing of flat glass up to the final polishing stages where rouge is generally used. Silica is used for foundry molds and cores, sandblasting, stone cutting, refractories, placing sand in furances, glass coatings and linings, laboratory glassware, construction, oil well fracturing for increased oil flow, filtering purposes, silicate of soda, silicon carbide, and others.

Jan 1, 1958

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By Francois E. Heuze

We demonstrate a new capability to analyze the behavior of circular shafts in jointed rock. This was made possible by the development of a new, axisymmetric, joint finite element (2). Whereas the only previously reported such element was singular (1) and inadequate at some orientations, the current element has been extensively validated (3). The need for including discontinuities in a shaft analysis comes from two sources. First, the various rock formations may have discrete jointing, bed- ding, and interface between them. Second, there is a joint at the boundary between a concrete liner and the rock, and possibly between the various segments of the concrete liner. To demonstrate the applicability of the new model, we analyze a vertical circular shaft 5.4 m in diameter, in a series of horizontally bedded sandstones and siltstones. The shaft excavation is followed through three initial steps: 6 m, 15 m and 24 m deep.

Jan 1, 1979

By Charles Bruce

Although much has been said about the high cost of exploration, both at home and overseas, little of a specific nature has been published on actual finding costs, if indeed such data has been developed. This contrasts sharply with our sister industry, petroleum, where finding costs for oil and gas are available for virtually any country In the world. The reason is largely attributable to the genetic complexity of the hard minerals, as opposed to petroleum, and the increasing difficulties we are facing in the search for new orebodies. We have available to us data on the annual exploration budgets of most of the major mining companies which show them to run into the tens of millions of dollars. My co-panelist, Dr. Walthier, Director - Corporation Exploration, St. Joe Minerals Corporation, New York, NY, summed up the feelings of many explorationists in a recent keynote address when he stated, "I would not recommend a mineral exploration program of a general nature in North America budgeted at less than three to four million dollars annually, spread over four to five years -- or smaller amounts for more years". We have the fact that many of the major companies now prefer to "buy into" a new mineral discovery, particularly overseas, because of the high-risk and high-cost of exploration. Is there, then, a place for the small investor, let us say with a budget of under $200,000 per year and, if so, where and how? This paper is directed toward the above question and is based on experience gained while managing a limited international exploration program, on a shoestring, over the past three years.

Jan 1, 1976

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By M. C. Radomsky

Approximately sixty, small, surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the safe standards of worker behavior and work conditions. Data were collected through the use of operation-specific, on-site safety records covering seven major occupational units. Workplace events observed (acts and conditions) were assigned a hazard classification; feedback, both immediate and delayed was initiated to improve safety performance. The experiences drawn from this pilot project have proven the need to continue to pursue this behavioral approach; however, a stricter methodology needs to be adopted in the collection and analysis of data.

Jan 1, 1987

By Thomas J. Neil, O&apos

Mine land reclamation is a comparatively new science-Although some mining companies point with pride to reclamation efforts of 20 to 30 years ago these were the exception rather than the rule. In the last ten years the skyrocket of environmental awareness has been awesome to behold. Future shock gripped mine operators everywhere as they struggled to cope with rapidly changing and escalating demands. The initial result was that two divergent points of view became dominant. Environmentalists said, "Put it back the way it was," and the miners responded, "Let's grow some weeds and hide it." These views are not surprising as they represent rather obvious alternative responses, albeit at opposite ends of the decision spectrum. The former case has prevailed more often than the latter, as most state and federal legislation -- both proposed and passed -- has required drastic alteration of the post-mining landscape so that evidence of prior mining is largely obliterated. An exception to this has been in porphyry copper country where the infrequent abandonment of mines has given emphasis to the second philosophy -establishing vegetative cover on mine waste materials. Now, it should come as no revelation to most mining people that both of these approaches to mine reclamation suffer from serious drawbacks when applied to open pit copper mines. First, whereas waste dumps and tailings dams can be vegetated with some aesthetic benefit, the massive presence of copper mining operations remains very prominent. It is difficult to conceal an open pit copper mine. Second, returning open pit copper mines lands to their original topography and productivity is simply not a reasonable alternative.

Jan 1, 1976

By A. C. Alexander

Chevron Resources Company owns and operates an open pit phosphate mine and mill 11 miles north of Vernal, Utah. The plant currently produces 500,000 tons per year of concentrate and has the capacity to produce 750,000 tons per year. The operation is currently being expanded to 1,300,000 tons per year of concen¬trate in order to supply a new fertilizer plant being constructed by Chevron Chemical Company in Rock Springs, Wyoming. A 10-inch, 96-mile pipeline is being built to transport the concentrate from Vernal to Rock Springs. The present and expanded operation will be discussed. HISTORY In 1915, Harry Ratliffe staked nearly 15,000 acres of low to medium grade phosphate rock along the southern flank of the Uintah Mountains. This deposit became the largest privately owned phosphate deposit containing approximately 700 million tons of reserves. Initial development of the deposit began in 1958 by San Francisco Chemical, a joint venture between Stauffer Chemical Company and Mountain Copper Limited. In 1968, Stauffer Chemical Company bought out Mountain Copper Limited and became sole owner and operator. In 1981, Chevron Resources Company bought the property from Stauffer and has operated the mining and milling operations since.

Jan 1, 1985

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company's Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979

By Homer S. Anderson

To clarify what r mean about this long title, I would like to define the term technology. A standard definition of the word "technology" is "a technical method of achieving a practical purpose". Incidently, another definition of the term is merely "technical language". The same dictionary defines the word "technology" as "having a special, usually practical, knowledge of mechanical or scientific subject." Naturally, the practical purpose of the subject with which we are concerned is solving of problems we encounter in the mining industry. I might further describe the subject of this discourse by defining the term "manager". An old definition, "one who dispenses the duties of his position with care and economy." In line with the above definition most of the technology with which we in the mining industry are confronted with deals with some form of cost reduction. This may be related to the speed of doing an operation or to saving of labor or supply costs. These can be improvements of an existing method or the result of new processes or inventions, such as new machinery.

Jan 1, 1974

By Floyd L. Prestridge

A test of a solvent extraction (SX) pilot plant featuring electrostatic coalescence has been performed by C-E Natco at the United Nuclear uranium mill in Church Rock, New Mexico. Operating in parallel with the United Nuclear SX system, the C-E Natco electrostatic SX pilot plant exhibited comparable extraction efficiency to the United Nuclear system which utilizes conventional mixer-settlers. The C-E Natco pilot, however, operated at much higher liquid loading rates and exhibited less communication between the aqueous phases of the extraction and stripping circuits.

Jan 1, 1983