Search Documents

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987

By I. K. Kapageridis

Digital photography combined with three dimensional models of topography, mining operations and restoration plans can lead to extremely realistic images and animations of the current and future states of a mine or quarry. The amount of work and the time required for the successful modeling of a mine and its restoration plan are surprisingly low nowadays. All this means that the visual impact of mining and quarrying operations can be easily assessed using common computer hardware and some dedicated software packages. LAVA Mining and Quarrying SA is a company committed to strive continuously for the highest possible environment protection at the company?s quarries. The pozzolanic rock quarry located at Xylokeratia is one of the company?s quarries on the island of Milos and the subject of the study presented in this paper. A thorough restoration plan of the Xylokeratia quarry is being completed by the company. For its purposes, a complete visual impact assessment study was performed at the Department of Geotechnology and Environmental Engineering of the Technological Education Institute of Western Macedonia. The procedures used in this study and the produced visual results are presented in this paper.

Jan 1, 2006

By J. Richard Kyle

Salt domes, their cap rocks, and the adjacent sedimentary strata represent a major economic resource in the Gulf of Mexico basin. Gulf Coast salt diapirs formed in response to sediment loading of the "mother" Louann evaporite sequence of middle Jurassic age, an effect that is caused by the buoyant nature of the lower density salt. Halokinesis progresses from nonpenetrative deformation that creates broad "pillow" structures into discrete high-amplitude diapirs. Because of its buoyancy, the top of the salt diapir remains near the land surface or the seafloor during much of its history as the basin floor subsides. The salt within the Gulf Coast diapirs is deformed complexly and commonly shows subvertical banding that represents modified sedimentary layers with different contents of nonhalite components. The most abundant impurity is anhydrite, which occurs as individual millimeter-scale crystals or as deformed clasts that generally form about 5% of most salt stocks. Many mature salt diapirs are mantled by a "cap rock" that consists of a lower anhydrite zone and an upper calcite zone, commonly separated by a discontinuous gypsum-bearing zone. The anhydrite zone forms as accreted layers of anhydrite grains and clasts that are left after episodes of halite dissolution. The calcite zone is a product related to petroleum destruction accompanying bacterial reduction of aqueous sulfate. Calcite-cemented siliciclastic strata occur above or alongside diapirs. The mineral resources of the salt-dome setting are remarkably diverse. Major economic products of the salt-dome environment are salt and cap-rock-hosted native-sulfur deposits, as well as petroleum resources that occur on the dome flanks and in the cap rock. Native sulfur forms as a result of bacterial sulfate reduction accompanying petroleum destruction to form hydrogen sulfide, which is subsequently oxidized to elemental sulfur, major amounts of which have been produced by the Frasch process from Gulf Coast salt-dome cap rocks. Some cap rocks have produced limestone, gypsum, and anhydrite for a variety of construction uses. Although traditional industrial-mineral resource production from Gulf Coast salt domes is shrinking, some cap rocks host potentially commercial concentrations of celestite and barite, as well as the metals Zn, Pb, and Ag. Furthermore, caverns, excavated within the salt stocks, serve as major storage facilities for crude oil (including the Strategic Petroleum Reserve), liquefied petroleum gas, and natural gas. These resources are products of fundamental geologic processes that are integral to the evolution of the Gulf of Mexico basin. Whereas production of some industrial-mineral resources, such as elemental sulfur, has declined in recent years, ample reserves of salt will allow production to continue into the foreseeable future. Further, there is potential for other mineral-resource production from cap rocks under favorable economic circumstances. Expanded use of caverns, excavated in the salt masses for material storage and disposal, is likely to continue into the next century.

Jan 1, 1999

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By M. O. Woodburne

The Mojave Desert province is comprised of a diverse group of mountains that range in elevation from about 2,000' (600 m) to 3,000' (900 m), separated by tracts of alluvial cover. The province is bounded on the southwest by the San Andreas fault, on the north by the Garlock fault, on the east by the Death Valley- Granite Mountains fault. Rocks preserved in the Mojave Desert Province collectively record a rich assemblage of Precambrian crystalline basement' ranging in age from ca. 1.8 to 1.35 Ga, upper Precambrian and Paleozoic Cordilleran miogeoclinal sediments and platform rocks, Mesozoic backarc and interarc shallow marine and continental sequences, locally emplaced Permian- Triassic syenitic plutons, extruded hypabyssal volcanic rocks of the ?Jurassic "Sidewinder Volcanic Series," and regionally intruded late Mesozoic granitoid batholithic rocks (Dokka et al., 1988). The Mojave block apparently was a high-standing element for much of the early Tertiary, with strata of Late Cretaceous or early Tertiary age preserved only on its margins. Beginning about in the late Oligocene an intense episode of regional north-south extension was developed in a roughly east- west trending belt that traversed the central part of the province. This extensional belt has been termed the Mojave Extensional Belt. The extensional regime lasted from about 22-17 Ma, and is generally divided into two phases. The first, from about 22-20 Ma records intense extension via the activity of crustal-scale, simple shear, low- angle normal faults, high-angle normal faults, and extensional fracturing, along with intrusion of intermediate to silicic volcanic rocks, including episodes of explosive volcanic activity. The Peach Springs Tuff, a major regional marker unit that extends across the Mojave from Arizona to about Barstow, forms an effective stratigraphic lid on the extensional interval, (i.e., is not rotated) and is dated isotopically at about 18.5 Ma. The extensional episode was followed by an interval of high- angle normal faulting and dike emplacement from about 19 to 17 Ma, and was accompanied by at least local uplift and volcanism. Most volcaniclastic and epiclastic sedimentary units of the central Mojave block post-date the interval of extension and normal faulting, and occur as a complex of marginal alluvial and more interior lacustrine facies that formed as recently as late Miocene (ca 13 Ma). Local sequences (e.g., Lava Mountains) record deposition up to about 8 Ma, but there appears to be a regional "gap" from then until at least local successions record Pleistocene deposition. Magnetic and isotopic age studies indicate a complex history of crustal rotations, distributed across a number of discrete domains, during the past 10 Ma. Some of the youngest volcanic and geomorphic features apparently developed at "holes" formed at the edges of rotated blocks.

Jan 1, 1995

By Wilbur C. (Original by) Helt

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being-looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals.

Jan 1, 1981

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982

By Marshall D. Himes, Erich U. Petersen

The Sheep Creek deposit near White Sulfur Springs, Montana, is a middle Proterozoic stratabound and strataform sediment- hosted massive sulfide containing 4.5 million tonnes (5.0 million tons) averaging 2.5% copper, and 0.1% cobalt in the upper sulfide zone (USZ) and 1.8 million tonnes (2.0 million tons) averaging 6% copper in the lower sulfide zone (LSZ). Mineralization is hosted in lower Newland shales and debris flow conglomerates in the graben controlled Helena Embayment of the Belt Basin. USZ mineralization is characteristically high in Cu, Co, Ni, Ba, As, Pb, and Ag. Mineralogically it consists of barite, pyrite, chalcopyrite, and tennantite with minor amounts of marcasite and various cobalt minerals. By contrast, the LSZ is higher in Cu, Ni, and Au and lower in Co, As, Pb, and Ag. Mineralogy of the LSZ consists of dolomite, pyrite, and chalcopyrite. In both zones significant amounts of cobalt, nickel, arsenic and copper are incorporated in pyrite rims. Tennantite controls the abundance of numerous trace elements in the ores. Fluid incluison data from hydrothermal USZ barite suggests that mineralization took place at temperatures in excess of 250°C, under relatively oxidizing conditions (f02 = 10-32+1) from moderately saline (1.1-3.5m), metal rich brines. The absence of barite in the LSZ suggests mineralization under more reduced conditions (f02 = 10.38+2). Mineralization was initiated following basin subsidence in excess of 400m. Contemporaneous with movement along a growth fault(s) was upward migration of hot metal-bearing fluids which permeated the loosely consolidated sediments and may have vented on the sea floor. The differences in the two zones may be explained by the effects of variations in local basin morphology and solution chemistry.

Jan 1, 1990

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

An open pit production planning method for stage mining is presented in this paper. The method brings solutions to the four most important parameters in stage mining : 1) the number of stages, 2) the size and geometry of each stage pit, 3) the mining sequence of the benches in the stage pits, and 4) the time of transition from one stage to the next. The method can also simultaneously optimize the ultimate pit, mine life, and production rate in each stage.

Jan 1, 1996

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017

By Y. C. Guan

The dissolution behavior of silver and copper form their elemental states and Ag/Cu alloys in ammoniacal solutions has been studied using rotating disc electrodes. The variables studied included concentration of ammonia, oxygen partial pressure and rotating speed of the disc. The results have been interpreted in terms of the mixed potential theory. The effect of local current resistance on the overall current has also been examined as a part of the governing theory of the dissolution. It was observed that the dissolution potential and the rate of dissolution were very much affected by the composition of the alloys.

Jan 1, 1995

By Q. Xu

The adsorption behavior of gold in ammoniacal solutions on to activated carbon has been studied. The gold loading capacity of the activated carbon used in the system and the recovery efficiency by the adsorption were examined. The parameters affecting the adsorption of gold on to activated carbon included temperature, agitation speed, concentration of &apos;cation and anion as well as that of ammonia. It was found that the maximum gold loading on activated carbon used was about 10 kg of gold per ton of carbon. The recovery of gold by the adsorption from ammoniacal solutions was dependent upon the initial gold concentration in the solution. A recovery of 98% of gold was obtained on to the activated carbon under experimental conditions after 120 hour adsorption. It was also found that the initial adsorption rate was relatively fast compared to the whole period of the adsorption. The apparent activation energy for the adsorption was measured to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on activated carbon was controlled by pore diffusion.

Jan 1, 1995

By Valerio Violo, Antonio Raschilla, George Kafantaris

"The Cityringen project in Copenhagen, Denmark will form a new circular line in the city center and will consist of 21 new stations (17 + four transfer stations) and approximately 31 km (19 miles) of earth pressure balance (EPB) twin-bored tunnels.The new tunnels passed under the historical building of Magasin du Nord, McDonald’s and two pubs in the heart of the city with a minimum cover of about 4 m (13 ft).To minimize the movements, a complex system of compensation grouting and jet grouting soil treatment was performed. A detailed action plan between the parties involved allowed coping with the critical tunnel boring machine’s (TBM) successful passage.The Cityringen is an extension of the existing metro line underground Copenhagen and will include the City Circle Line, 15 km (9.5 miles) of twin tunnels looping around the city. The City Circle Line will form a new circular track inside the city center and will intersect the existing M1 and M2 lines at Kongens Nytorv and Frederiksberg stations, as well as suburban train services at København H, Østerport and Nørrebro. It will extend the Metro network to the Nørrebro, Østerbro areas and the central station at København H (Fig.1). The two new lines M3 and M4 will run on the same tracks, but the M3 will be a circle route running around the entire line, whereas the M4 will drive from the station to the north side of the city.The €1.5 billion design-build contract was awarded by Metroselskabet in January 2011 to the Copenhagen Metro Team (CMT), a joint venture (JV) between the Italian companies Salini, Tecnimont Civil construction and Seli SpA. Since the bankruptcy of Seli SpA and Tecnimont, Salini Impregilo now owns 100 percent of the JV shares. Seli Tunneling Denmark ApS, a subcontractor to CMT, was initially constituted as a Seli SpA subsidiary and, following the economic difficulties of Seli SpA, was acquired in 2015 by Salini Impregilo. Seli Denmark is in charge of the tunnels excavation and lining and owns the four 5.84-m (19-ft) diameter Seli/Kawasaki earth pressure balance machines."

Jan 5, 2017