Search Documents

By J. A. Cervantes

A statistical model for assessing the risk of ground subsidence in abandoned mine areas is presented. The model is based on the relationship that exists between .the frequency and the location-of subsidence events in a given area and the physical conditions of the ground. These conditions can be described by a series of geological, mining, and physical variables. The model suggests the existence of regions in the multidimensional space of variables which are associated .with increases or decreases in the frequency of subsidence events. Regions associated with an increase in the frequency of subsidence events correspond to regions of higher risks, and vice versa. Risk assessment is based on the ability to express the limits of these high and low risk regions in the, space of variables, and on the ability to express the degree of membership of blocks of land within any of these regions. The theoretical framework for the model is extracted, from discriminant analysis. Risk is quantified by the probabilities of membership of blocks of land into any of these regions. Risk maps are produced by displaying membership probabilities in. appropriate contouring levels. The model has been applied in two urban areas where subsidence of the ground has been active in the past. The two areas are Penn Hills, near Pittsburgh, and Scranton/Wilkes-Barre in northeastern Pennsylvania. In this paper, only the results for the Scranton/Wilkes-Barre area are presented. Those for the Penn Hills area have been presented elsewhere (Cervantes, et al, 1990). In the- Scranton/Wilkes-Barre area, geostatistical estimates of variables likely to affect the stability of the ground were made using samples from 53 drillholes. The estimates were made for 2000x2000 ft squared blocks of land covering the study area. Discriminant functions were computed from the estimated variables and used to establish regions for classifying blocks of land into one of these two populations: 1) blocks not likely to have a subsidence event, and ii) blocks likely to have one or more subsidence events. The same, discriminant functions were used to compute membership probabilities for blocks of land to tall within any of these two populations. These probabilities were contoured to produce a risk map. The risk map produced compares well with the location of the subsidence events which have occurred to date in the area.

Jan 1, 1992

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By L. H. E. Weyher

The Bethlehem Mines Corp. is a captive mining subsidiary of Bethlehem Steel Corp. Its coal production is tied to the demands for and production of steel, a situation that has to balance between the following two extreme strategies: (1) either the mines are designed and operated for some optimum production level and the demand fluctuations within the steel corporation are met by supplementary corporate coal sales and purchases, or (2) the mines absorb all the demand fluctuations, regardless of the effects on mine costs. A rational definition of the best strategy between these extremes is, of course, needed but is very difficult to formulate in view of the complexity of the many factors that would have to be included in the analysis. Consequently, rather than setting profit targets for each given mining division and/or individual mine, the practice evolved to set production targets for producing specified tonnages of coking coal for shipments to the ovens located at the corporation's iron and steelmaking plants. This in turn leaves the mines with the dilemma of having to explain demand-related cost-per-ton fluctuations while essentially depriving them of the ability to control profit through tonnage optimization. In the early 1970's, the coal prices rose significantly, while other factors led to sagging productivity in underground coal mining. Thus, the role of Bethlehem's coal operations in the corporate profit picture gained in relative importance. This, in turn, sparked a closer attention to the coal mining cost structure and factors controlling productivity. At the same time, the drastic increase in the capital needed to open a new mine also increased the amount of planning required to minimize risks. All of this called for more well-defined, quantitative operating data. Bethlehem therefore launched, in the early 1970's, a number of innovative steps that, as the future may show, represented pioneering contributions to the growing sophistication of North American underground coal mine planning and management control practices. This case study describes the changes that led to the current implementation of a novel production reporting system at Bethlehem's coal mines. These changes took place in two distinctly different phases. The current system that resulted from the Phase II developments utilizes, of course, experience gained earlier and is expected to be amplified to incorporate more advanced concepts and technology as future experience dictates.

Jan 1, 1979

By Dean S. Rogers, R. A. Metz

The conventional role or exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1992

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993

By A. Bascetin

The human requirements have increased rapidly depending on population density and urbanization thus industrialization has grown steadily. As a result of the situation, the greenhouse gas emissions into the atmosphere and the global warming have increased slowly. Today this effect has continued to increase. Therefore, the effects of greenhouse gases in all areas of production must be controlled. The study presents the methods of determination the CO2 emissions (CO2-e) and energy consumption in aggregate production. The aggregate constitute approximately 70% by volume of concrete that has widespread use as construction material in the world. One of the most important elements in today's terms is sustainable use of resources and minimum CO2 emissions (CO2 + CO + NOx + CH4.vb.) at every stage of production of aggregate. Therefore, these elements must be taken into consideration in the aggregate production standards. The choice of production method of aggregate is very important for optimum use of energy and effects of greenhouse gas emissions. So the properties of the aggregate material must be known well to obtain the target. Within the scope of this study, the unit value of CO2-e that release when the production of aggregate in different formations is determined for our country. Thus, the effects of green house gas emission can be evaluated according to the characteristics of material in aggregate production planning. In this study, energies consumed during the production of aggregates at a quarry in Istanbul Cendere region were investigated by taking the different formations encountered at the quarry into consideration. The unit CO2 emission values per ton of produced aggregates were calculated as a result of this investigation. Besides, energy consumption values of previous months at this quarry were taken and the unit CO2 emission values were also calculated.

Jan 1, 2011

Fine coal is substantially more costly to process than coarse coal because of technical difficulties associated with separating fine particles and removing process water from both clean coal and refuse. Therefore, companies are often forced to discard coal fines to waste impoundments. According to a recent report published by National Research Council, the U.S. coal industry is discarding 70-90 million tons of coal fines annually to 713 active impoundments, most of which are located in Central Appalachia. On October 11, 2000, a 72-acre impoundment near Inez, Kentucky, accidentally released 250 million gallons of coal slurry into nearby underground mines, creeks, rivers, and schoolyards, thereby creating serious environ-mental concerns. Fortunately, recent advances in separation technologies make it possible to recover fine coal more efficiently from existing coal preparation plants and from waste streams previously discarded to impoundments. The availability of these new technologies allows companies to increase profitability and minimize environmental risks, which are conducive for achieving sustainable mining.

Jan 1, 2003

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By E. W. Geist, W. J. Bronkala

PRINCIPLES OF MAGNETIC SEPARATION The application of magnetic separators relies on the different behavior of individual mineral particles under the influence of magnetic forces. When exposed to a magnetic field, all materials are affected in some way. According to whether materials are attracted or repelled by the magnetic field, they are designated paramagnetic or diamagnetic, respectively. Paramagnetic materials are attracted along lines of magnetic force from points of lower magnetic field intensity to points of higher magnetic field intensity. The very strong response of some materials to a magnetic field is sometimes designated ferromagnetic and the particles attracted frequently retain magnetic properties after the applied magnetic field is removed. Diamagnetic materials are repelled along the lines of magnetic force from points of high magnetic intensity to points of lower field intensity. Only limited commercial use of diamagnetic effects has been made. For practical applications, the paramagnetic groupings are: 1. Strongly magnetic (ferromagnetic) 2. Magnetic 3. Weakly Magnetic 4. Non-magnetic The limits of these groupings are not well defined and will vary in some mineral species. Only a few minerals are ferromagnetic (magnetite is an example) and arbitrarily some investigators have selected 10,000 gauss, or 1 Telsa, as the dividing line between low and high intensity magnetic fields. I. S. Wells has developed a table indicating the magnetic intensity required to separate a selected grouping of minerals which is shown in Table 1 on page 2. A similar table has been developed by Carpco Inc. of Jacksonville, Florida in conjunction with the use of its high tension separators. This table, Table 2 on page 3 shows other minerals grouped in the broader categories cited above. Magnetic separation methods are used either to separate valuable minerals from nonmagnetic waste or magnetic impurities or other valuable magnetic minerals from bulk nonmagnetic values. Magnetically susceptible mineral particles occur as either individually discrete particles,

Jan 1, 1986

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By P. Kolettas

The development of novel methods for the investigation of the subsoil contributes to the improvement of geotechnical research, enhances the obtained geotechnical characterization and may reduce the investigation cost by reducing the number of required tests. Non-destructive testing methods, performed either in situ (i.e. electrical tomography, seismic refraction, etc) or in the laboratory can provide initial data and perhaps estimates of rock/soil properties. This study focuses on the development of rock material properties and/or characteristics based on non-destructive laboratory testing of a number of stones, ranging from porous (bioclastic) limestones to impervious marbles. Seismic velocity measurements as well as attenuation signals were digitally recorded using a digital oscilloscope. Data were processed using a novel technique of spectral analysis available through special Matlab packages employing Fourier transform methods. More specifically, the NFFT (Non Equispaced Fourier Transform) transformation was applied to seismic waves traveling through the subsoil using the Autosignal program (by Seasolve) and the Specgramdemo program included in the Signal Analysis toolbox of Matlab 6.5 (Mathworks). Results indicate a definite relationship between the frequency content of the signal and the rock type as well as the degree of saturation of the specimen.

Jan 1, 2008

By E. Topuz, Xing Wu

INTRODUCTION The air flow in the mine ventilation network can be categorized in three ways: natural splitting, controlled splitting, and semi-controlled splitting. In natural splitting, the air flow in branches of a ventilation network apportions itself according to the aerodynamic resistance of the branches. In controlled splitting, a prescribed quantity of air is circulated through each branch. In semi-controlled splitting, flow in some branches is fixed to a desired quantity while in other branches it is split naturally. In practice, the mine ventilation networks present the latter two situations. Usually, the resistance of each branch in the network is known and the quantity of air in the working place is predetermined by safety considerations. If the number of branches whose airflow quantities are known is equal to or larger than the number of the fundamental meshes in the network, then the network becomes a controlled splitting network (Wang, 1982 a). Otherwise, it is a semi-controlled splitting network. If no booster fans are used in the network, the problem can be solved as either controlled or semi-controlled splitting networks in order to determine the main fan pressure and regulator size and location. All techniques are based on Kirchoff's flow and energy conservation laws and Atkinson's Equation. Booster fans can be used in controlled and semi-controlled splitting networks. It has been proven both theoretically and practically that using booster fans in these ventilation systems can improve flow distribution and reduce consumption of power (McPherson et al., 1985). The current techniques used in determination of booster fan location and size include simulation, linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. These techniques can be classified into two groups. The first group, including linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing techniques, deals with controlled flow networks. The second, simulation, can be applied to the handling of semi-controlled flow networks. Mathematically, the problem of controlled splitting networks can be solved more easily than that of semi-controlled splitting networks. This is because the controlled flow network can be formulated as a linear programming problem, for the solution of which there are several sophisticated algorithms. Moreover, the semi-controlled flow network is usually modeled through nonlinear programming, for which there are no universally applicable solutions. The procedure described by Wu and Topuz, 1986, can be used to convert a semi-controlled network to a controlled flow network, and the problem can then be easily solved by the techniques used for solution of a controlled flow network problem. In practice, a mine ventilation network may change from controlled splitting to semicontrolled splitting with advancement of mining. This dynamic nature of mine ventilation makes the problem more complicated and necessitates development of new solution procedures which will consider the overall economics of the system. CONTROLLED SPLITTING NETWORK The problem in controlled splitting networks with booster fans is to determine the operational characteristic of the main fans, and the location and size of booster fans and regulators. The objective is to satisfy the air flow rate requirement for each branch while minimizing consumption of energy. The techniques used for the controlled splitting network problem include linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. The objective function and constraints can be expressed as follows (Wang and Pana, 1971): [ ]

Jan 1, 1989

By Taehong Kim, Changsoo (Kevin) Moon, Anil Parikh

"This paper presents an overview and performance evaluation for a reconditioned decades aged open type hard rock TBM utilized for the twin running tunnel excavations of the Second Avenue Subway Project in Manhattan, New York. The TBM tunnel lengths are approximately 2,370 m (7,800 ft, east TBM Tunnel) and 2,190 m (7,200 ft, west TBM Tunnel) with a 6.7 m (22 ft) bored diameter. This “senior” TBM mined through metamorphic rocks consisting of schist, granofels, and pegmatite, and encountered various adverse geological structures, including some relatively heavy groundwater inflows. The ground support was generally pattern friction rock bolts, and steel sets were used in poor ground. This paper presents TBM characteristics and the subsequent performance, such as machine utilization, downtime, cutter consumption rate, net penetration rate, and daily advance rate. Machine operating parameters including thrust, torque, gripping force, and cutterhead RPM, are compared with various accompanying ground conditions. The performance changes between the adjacent tunnel sections are also presented. INTRODUCTION Project Overview The Metropolitan Transportation Authority Capital Construction (MTACC)’s Second Avenue Subway (SAS) Program consists of four (4) phases from 125th Street to Manhattan Battery Park along the 2nd Avenue (see Figure 1) in Manhattan New York. As a part of Phase 1, Contract 1 was awarded to S3 JV (Skanska/Schiavone/Shea) to build a TBM launch box and subsequent twin TBM tunnels from 92nd Street to 63rd Street under 2nd Avenue. Contract 1 was one of the key contracts in Phase 1 to pre-excavate through the footprint of the follow-on underground stations (72nd St. Station, 86th St. Station, and 96th St. Station) by hard rock TBM excavation. The project team included Client MTACC, S3 Tunnel Constructors, Designer, Aecom-Arup JV, and Consultant Construction Manager, Parsons Brinckerhoff. The major elements of Contract 1 included construction of TBM Launch Box supported by secant pile and slurry walls and mining of twin TBM tunnels with a combined tunnel length of approximately 4,560 m (15,000 ft). The dimension of the TBM launch box was approximately 247 m (810 ft) long from 92nd Street to 95th Street, 21 m (70 ft) to 24 m (80ft) wide along the 2nd Avenue, and 18 m (60 ft) to 21 m (70 ft) deep from the ground surface. The launch box was later used for the follow-on 96th Street Station."

Jan 1, 2016

By Dan J. Van Roosendaal

A closely spaced grid of survey points was installed over the tensile zone of a longwall panel in southern Illinois and monitored daily during subsidence to document the complex ground-surface movements associated with dynamic subsidence. Vertical and horizontal displacements were used to calculate maximum tilts and principal strains within the grid. The dynamic nature of subsidence is made evident by changes in both the direction and magnitude of maximum tilts and principal strains. The maximum tilt (smax) of 0.036 and maximum tensile strain (Emax) of 0.027 were measured after subsidence and were oriented transverse to the longwall panel. Observations of surface fracturing were correlated with strain determinations to estimate a surface strain at incipient cracking (E;) of 0.006 to 0.009. Using shallow inclinometers, a linear variation of horizontal displacement with respect to depth was observed, suggesting a neutral¬axis bending mechanism for near-surface deformation. Horizontal displacements transverse to the longwall panel reduce to zero at a depth of 40 feet. A linear relationship between strain and curvature was used to estimate ground-surface curvatures associated with Emax (0.00068 ft-1) and E; (0.00015 to 0.00023 ft-1). The curvature estimates are consistent with published results.

Jan 1, 1986

By J. E. Lawver, F. S. Knoll

Introduction Electrostatic separation is the selective sorting of solid species by means of utilizing forces acting on charged or polarized bodies under the influence of an electric field. Electrostatic separation is effected by adjusting those forces acting on particles due to the electric field as well as co-acting forces such as gravity or centrifugal forces so that the different species will have different trajectories at some predetermined time. Electrostatic separations can be broadly defined as being either electrophoretic or dielectrophoretic. Electrophoresis is the separation of charged particles in an electric field, whereas dielectrophoresis is the separation of neutral particles in an electric field1. Examples of an electrophoretic separation can be found with sepa¬rations that use corona charging (ion bombardment), contact charging (triboelectric) and conductive induction. Dielectrophoresis motions are due to the stress and repositioning of charges, i.e. polarization of a neutral particle when exposed to a non-uniform electric field. Separations made using corona discharge devices are often called high-tension, electrodynamic or ion bombardment separations. These are the most prevalent in use today in mineral processing. Dielectrophoretic separation of most minerals is based on differences in dielectric constants of the solid species and usually requires the use of expensive intermediate dielectric fluids. Dielectrophoresis has not been employed for industrial mineral separations, though its effects pose interesting possibilities1, and pilot-plant units developed by the U.S.B.M. are available for testing2. Our discussion will be limited to the three forms of electrophoresis found in commercial practice. Typical Industrial Separations Typical industrial applications of electrostatic separation are: 1. Dry concentration of heavy minerals: ilmenite, rutile, zircon, monazite, xenotime, columbite-tantalite, cassiterite, hematite, scheelite and others. 2. Separation of salts: halite-sylvite, etc. 3. Purifications of foodstuffs such as the removal of impurities and

Jan 1, 1986

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985