Search Documents

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By F. Woodcock, A. R. Laplante

A test to characterize the amount of gravity-recoverable gold (GRG) in an ore is described. Typical GRG results are given and possible uses are discussed. The overall database, which includes 68complete tests, is presented. The ore samples treated had an average GRG content of 63% of the total gold in the sample, with a standard deviation of 20% and a range of 3% to 97%. Both the F8(, of gold and the GRG content at a grind of 100% finer than 850 pm correlate well with the overall GRG content (at 80%finer than 75 pm). The primary use of the test is to determine whether gravity recovery should be used and how. Results can also be used to predict gravity recovery, as many of the ores tested are from plants employing gravity recovery. Gravity-circuit simulation can be used to refine recovery estimates or for optimization studies.

Jan 1, 2000

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By Johannes Wageneder

As a reaction to the fire accidents in tunnels in Europe Designers nowadays have to demonstrate the integrity of underground structures such as metro systems, railway and road tunnels in case of fire load wherever as a consequence of a lining collapse surface infrastructures or residential areas could be affected. To respond to this FLAMDOCS allows to calculate the stability of reinforced concrete structures during fire load for a series of prede?ned time steps. Elementary theories of non linear material properties and reinforced concrete structures are used.

Jan 1, 2003

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By Raymond E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental baseline studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months, and the first gold bar was poured in March of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitoring program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine's twenty year life. Nonmined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By A. De Daio, D. W. Fuerstenau, P. C. Kapur

Because of its pronounced tendency to undergo visco-plastic flow, coal ground in the energy- efficient high-pressure roll mill invariably comes out as a briquetted product which must be disintegrated in a conventional type of grinding device such as the ball mill. The aggregates comprise comminuted coal particles that are apparently extensively cracked and weakened during passage of the coal through the high-pressure rolls. Their deaggregation in a ball mill in the second stage is accompanied by further grinding of the coal with a relatively small expenditure of energy. Thus in spite of energy dissipation in briquetting in the roll mill and in disintegrating the briquettes in the ball mill, significant energy savings are possible in the fine grinding of coal in a two-stage serial grinding mode, as compared to ball mill grinding alone. It has been determined that for the best results the energy invested in the two grinding stages must be apportioned in an optimal manner, the energy consumption in the ball milling step is comparable to, even in excess of, the energy spent in the high- pressure roll mill; and 20 to 50 percent energy savings might be possible in grinding coal to minus 200-mesh size by this two-step process, as compared to conventional milling.

Jan 1, 1995

By Arafat Ghosheh, Yousuf Abu-Rish, Darwish Amara, Mohammed Baderkhan

The Jordan Phosphate Mines Company is one of the world's major phosphate rock and phosphatic fertilizers producers (the second largest phosphate rock exporter), with ore reserves exceeding 2 billion tonnes, mainly located in the Eshidiya area. The Eshidiya phosphate deposits, 120 km north-east of Aqaba, are of sedimentary origin (as are all phosphate ore in Jordan). Three exploitable beds (Al, A2, and A3) with variable content of P205, CaO, SiO2, etc., are processed in order to produce 68-70,73-75, and 75-77% TCP grades. The A3 bed, which is characterized as the most siliceous containing 40-48% TCP, requires physical beneficiation using wet scrubbing, screening, and desliming by hydrocylone, followed by anionic conventional flotation to achieve 75- 77% TCP grade. For the last 15 years extensive laboratory and pilot tests (including physical, chemical, and mineralogical studies) were carried out. After operating the industrial plant, certain modifications were deemed necessary to adjust the operational parameters and the final flowsheet, which was followed to obtain the targeted quantity and quality of concentrate.

Jan 1, 1999

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By A. P. Schissler, S. Badr, U. Ozbay, M. D. G. Salamon

Yield pillars are used in deep coal longwall mines, where the depth of cover is so great that a conventional chain pillar design tends to be unsuccessful. The design of yield pillars in deep U.S. mines has been based mainly on experience, pressure arch theories, numerical modeling, and empirical methods that originated in the eastern U.S. coal mines. This paper offers field experience based guidelines for the design of yield pillars through analysis and evaluation of numerous case histories. Case histories of yield pillar applications were collated and critically reviewed to identify trends in data that can be used to formulate the design guidelines. Convincing trends observed in the case of successful case histories indicate that yield pillars should have a width to height ratio in the range from 2.8 to 6.0, a stability factor during development between 0.4 and 0.6, and shed between 94% to 98% of the cover and abutment load, as provided by the Carr-Wilson (1982) method. Also, yield pillars should be utilized in coalmines only where the roof and floor rock have a CMRR rating of 50 or better.

Jan 1, 2003

By K. R. Weller, U. J. Sterns, P. S. B. Stewart

Complex sulphide ores usually require very fine grinding of the whole ore stream to achieve adequate liberation. Recent improvements to DSM screens have made this device appear competitive with cyclones in circuits treating these ores. A DSM screen and cyclones were tested in pilot-scale grinding of a copper, lead, zinc ore and the resultant data were used to establish a multi-component simulation model. The model was used to assess the influences of mill environment, circuit flows and pulp densities, final product properties (size, relative size and SG of the values, and liberation characteristics) and a second grinding circuit on capacity and product size distributions, and hence define conditions for which one device is better than the other.

Jan 1, 1992

By F. N. Kissell

The US Bureau of Mines undertook a study of those factors influencing worker escape from an outby coal mine fire. The results of this investigation were two-fold. First, those factors affecting escape from a mine fire were defined, and second, the relationships between these factors were identified. Although the individual components had been studied before, little information was available on their interdependence. Fault tree analysis was used to evaluate the miner escape scenario. After constructing the fault tree, a two-phase analysis of the tree was conducted. During the first phase, the minimal cutsets of the fault tree were identified and ranked. These sets were the smallest sequence of events leading to fatalities during the fire. This ranking revealed that reduced evacuation delays, improved self-rescuer training, and improved stopping construction were important in controlling fatalities during escape from the mine fire. The second phase involved additional analyses of the fault tree. These evaluations were started by first determining occurrence probabilities for each event in the fault tree. Two types of sensitivity analyses were then conducted. The first analysis dealt with changes in event probabilities and their impact on the likelihood of fatalities. The final sensitivity analysis considered dramatic reductions in the probability of fire fatalities. This revealed what event probability values were necessary to reach this level. These results have revealed various remedial actions that could be used to improve the survivability of an outby mine fire.

Jan 1, 1990

By Francis R. McAllister

SYSTEM ENGINEERING Years ago, while attending Harvard's Advanced Management Program, Professor Robert Hayes introduced our class to the, then not-so-familiar, concept of systems engineering. First assignment-dinner at The Benihana of Tokyo Restaurant! Delighted, but a bit mystified with the assignment; we had dinner at Benihana. Back in class, Professor Hayes inquired about the assignment and persuaded us; that Rocky Aoki's business formula for Benihana was not necessarily Japanese cuisine, but rather the systematic way in which he moves more people-if you will, processes more people through his restaurants than his competition, by systematically linking all restaurant functions. For instance, the bar is a holding area in which patrons ideally wait no more, or no less, than 20 minutes. When seated, your table, which accommodates eight, is filled with eight even if you are a party of two. The Japanese chef is also the entertainment, and when, at the end, he cleans the grill, you are being subtly prompted that dinner is over. The bill accompanies ice cream, systematically delivered shortly thereafter. You are expected to pay promptly and depart, as there are eight more, mostly unacquainted, people who have waited 20 minutes in the bar, and who are assembled ready to be seated at your table. For me-this was electrifying. I understood the concept, concluded it was very powerful and felt prepared to conquer whatever, by means of its application. That was years ago and I can safely say I have yet to fully realize on the euphoria of that moment. Why? Well, I simply conclude: • The concept of systems engineering is simple and not revolutionary, but The application of systems engineering is far from simple and is revolutionary.

Jan 1, 2004

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By V. Paul Keran

Design of the Bajo de la Alumbrera project started in June 1995. Concentrate production began early in the third quarter of 1997. The project is situated in northwestern Argentina. Alumbrera is being developed by Minera Alumbrera, which is owned by MIM Holdings of Australia (50%), North Limited of Australia (25%) and Rio Algom of Canada (25%). Alumbrera is Argentina's first modern copper mine. This article outlines the key process- and plant-layout features that were incorporated in the Alumbrera concentrator design. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity-gold circuits in both the primary and the regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By Robert R. McDougal, Anne E. McCafferty, Bruce D. Smith

Magnetic, electromagnetic, and radiometric airborne survey data have been used in regional and local (drainage basin) scales. In a regional geoenvironmental assessment of the state of Montana, magnetic and radiometric data compiled from airborne surveys were used along with other digital geologic and geochemical data to prioritize mining districts for potential acid water generation. Probability ratio mapping was done in order to integrate the interpretation of many different digital data sets. On a more local scale, the Animas (CO) and Boulder Basin (MT) watersheds have been studied using helicopter geophysical surveys. The airborne geophysical surveys show many more structural features than the geologic maps. Combined interpretation of the geophysical data sets using the probability ratio method has resulted in identification of areas of alteration. Airborne radiometric data in the Boulder Basin area suggests that rocks with high potassium and thorium also have a high acid water buffering capacity.

Jan 1, 2000

By J. Bigu

Ventilation conditions in working environments are usually studied by anemometry or, in complex cases, b using special tracer gases such as SF6 and 85Kr. in conjunction with chromatographic and radioactivity techniques, respectively. In some working environments, such as underground uranium mines, however, use can be made of the natural radioactivity environment (e.g.. 222rn. 220rn, and their progeny) to investigate mine ventilation conditions of practical interest. Theoretical studies and experimental data in several underground uranium mines and mine locations show that certain thoron progeny to radon progeny concentration ratios are very good indicators of ventilation conditions. Furthermore, the growth and decay of radon progeny and thoron progeny provide valuable information on mine air residence and clearance times. Some specific examples have been analyzed, such as bacterially-assisted uranium leaching operations in a partially enclosed stope, and the effect on the underground environment of turning ventilation fans on and off for a period of time. Air residence times and other variables of interest, determined from the mine radioactivity environment, were compared with more traditional techniques, such as anemometry and tracer gas chromatography. These studies were also extended to a wet non-uranium mine which exhibited relatively high concentrations of radon and its progeny.

Jan 1, 1989

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001