Search Documents

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By William E. Hole

The sand and gravel industry provides an enormous quantity of materials vital to the maintenance of low-cost construction. There has been little effort to conserve this valuable natural resource. In fact, existing regulations which affect sand and gravel operations act more to waste these materials than to conserve them. Another factor affecting the industry is new legislation requiring the reclamation of worked-out pits. Although such legislation creates many administrative headaches for a sand and gravel operator, there exists the possibility through such legislation of gaining some conservation measures that could be helpful to the industry.

Jan 1, 1974

By Muhammad O. Rahim

The importance of planning ventilation systems in modern coal mines cannot be overemphasized. Interconnected entries, airflows around and through mined-out areas, leakages through stoppings and other control devices, and the use of multiple fans all contribute to the complexity of ventilation network analysis. Fortunately, the availability of computer programs (e. g., Didyk et al., 1978; McPherson, 1966; Wang and Saperstein, 1970) has greatly reduced the difficulty in net- work analysis. However, to obtain a suitable solution to the practical problem, a ventilation engineer has to simulate various conditions based on the proposed ventilation layouts and the capacities of available fans. It is often a trial-and-error process, although engineering knowledge and judgement are required.

Jan 1, 1982

By R. M. Guymon, D. D. Lauriski

Safety management can best be described as how each company deals with the control of hazards (human or mechanical) to reduce costly accidents and employee injury caused by accidents. Properly used, effective safety management can mean the difference between being a highly productive, cost-efficient operation or one that "walks the fence," that is less productive with higher product costs. At Utah Power & Light Co's mining division, effective safety management has been used as tool to achieve this difference and remains as the number one priority to maintaining that difference.

Jan 1, 1990

By M. G. Hester, G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/ block-kriging shortcut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve-grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and which is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1997

Steady state simulation has become a highly effective approach to the optimization of existing mineral processing plants and the design of new facilities. Accurate phenomenological models imbedded in user-friendly software packages make this advanced technology available to the mineral processing engineer. The new version 2.0 of the USIM PAC software package contains many improved features, and a new Windows 3 graphics interface. The main features include Objective-Driven Simulation, new fields of application, improved data processing algorithms and improvements in the design and optimization capabilities.

Jan 1, 1992

By B. Ni, J. D. Robertson

A new radioactive tracer method for the measurement of airflow in inaccessible airways was developed. The method can be used in situations where studies of the mine-ventilation system are not possible using conventional flowmeters (anemometers). The method was tested in the ventilation laboratory at the University of Kentucky and in the US Bureau of Mines Experimental Underground Coal Mine and was utilized in leakage, dilution and flow-velocity measurements.

Jan 1, 1998

By Gordon E. Ager

A technique for the synthesis of mineral processing flowsheets from laboratory batch test data is described and examples of the application of the procedure are given. The procedure requires the collection of kinetic data, the optimization of the flotation time in each separation stage, then simulation of the material balance for a continuous circuit.

Jan 1, 1989

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By R. W. Smith, R. K. Mehta, X. P. Zheng, A. M. Raichur, M. Misra

Experimentation was per formed on the flotation of apatite and dolomite separately using anionic collectors in the presence of Mycobacterium phlei. Also, the flotation of mixtures of dolomite and apatite in the presence of anionic collectors and in the absence and presence of the bacterium were studied. It was found that M.phlei functions as a depressant for both minerals. However, it functions as a better depressant for dolomite than for apatite. Experimentation was extended to two different Florida dolomitic phosphate rocks. In this investigation a concentrate grade of less than 1.0% MgO was achieved with a 75% P2O5 recovery.

Jan 1, 1999

By A. W. Deurbrouck, W. W. Agey

Introduction The modern wet concentrating table is a rectangular or rhomboid shaped normally rimed-deck operated in essentially a horizontal plane (Fig. 23). A drive mechanism imparts a differential motion to the deck along its long axis while water flows by gravity along the short axis. Tables are currently employed for processing large tonnages of coal and lesser tonnages of barite, beach sands, chrome, glass sand, garnet, iron, manganese, mica, phosphate, potash, tantalum, tin, tita-

Jan 1, 1985

By M. Sengupta

Vast reserves of oil shale occur in the Green River formation in Colorado, Utah, and Wyoming. The room-and-pillar mining method is applied to flat-lying sedimentary deposits. Important elements in mine design include mine orientation, vertical location of the mining zone, selection of roof horizons, room span and pillar size, barrier pillar size, panel dimension, and layout of mains and submains.

Jan 1, 1988

By R. D. Willette

The Hector Mine deposit in the California Mojave Desert has a magnesium-rich clay that formed when lithium and fluorine were introduced into isolated fine lacustrine volcanic sediment during the Pliocene. The intensely deformed deposit has been supplying the highest grade thixotropic clay to the coatings industry for over half a century. A thixotropic clay displays the property of changing from a gel to a sol when shaken, and increases in strength upon standing.

Jan 1, 1995

By Michael L. Nave

An existing coal mine's raw coal 60 inch conveyor system had become productivity bound by a capacity of 3,500 tph. The existing conveyor drives were fixed speed wound rotor induction motor drives installed in 1983. The fast track upgrade installed variable speed medium voltage variable frequency drives to speed up the conveyor to a capacity of 5, 000 tph. The installation took place over a one week system shutdown during Christmas 2000.

Jan 1, 2002

By P. T. Luckie

More efficient classification with a single hydrocyclone through equipment and/or operating design changes does not appear possible. However, improvement in classification efficiency by increasing the sharpness index and decreasing the apparent by-passing while changing the cut size is possible through proper staging of inefficient hydrocyclones. But feasible multistaging requires achieving the necessary material balances around the units. Because of the interactions among the units, these balances require extensive iterations. The final step before commerical installation should be a laboratory demonstration, in order to define the control algorithm required to maintain stability. However, eventually a sufficient knowledge base should be developed that will permit simulation in place of laboratory testing as well as the incorporation of a feed forward strategy.

Jan 1, 1989

Health and safety issues are very important to the mining industry. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last three decades are presented and critically evaluated with respect to factors such as the number of workers and annual production. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greece are also discussed.

Jan 1, 2002

By H. F. Hennigar, D. L. Pawson, E. J. Foell

Results of an analysis of abyssal benthic megafauna based upon review of nearly 250 hours of videotape and 2149 bottom photographs are presented, and the utility and limitations of such analyses in deep sea biological studies are discussed. The images were acquired at depths of 4400-4800 m during a resource assessment cruise aboard the RV Prospector using a unique, deep-towed, television telemetry system coupled with 35-mm photography. The data review was carried out in support of NOAA efforts to provide adequate environmental baseline information before industrial exploitation of nodule deposits and concurrent monitoring begin.

Jan 1, 1991

By Greg Barfoot, K. Payne

Condition monitoring of conveyor belting has become an established tool for maintenance programming, replacement strategies and quality assurance for belt conveyor systems. What is less well known is that the condition of the conveyor belting is usually a symptom of problems in other areas rather than the problem source. This paper presents an overview of the state of the art in belt monitoring and the move towards on-line NDT systems. The use of belt monitoring data as an indicator for overall system design, maintenance and operation is also discussed.

Jan 1, 1996

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

Jan 1, 1997

By A. S. Polubinsky, V. P. Chernyak

A further development of the theory of heat- and mass transfer in the system “strata - mine opening" is necessary for an improvement of the existing technique of heat calculation of mines and other underground constructions. A generalized boundary problem of heat- and mass conduction in strata around an opening as a theoretical ground for that purpose and several particular situations, important from the point of view of an opening and surrounding strata heat state analysis, as well as results of numerical experiments executed for such analysis are presented.

Jan 1, 1997