Search Documents

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999

By J. C. Agarwal

Major scientific discoveries cannot be programmed. New or frontier technology, however, can and should be planned. It is the vital force underlying the business strategy of a vigorous and profitable mining and metals company. Generally, a radical departure from existing technology is required to 1) Enhance the competitive value of ore reserves, i.e., to turn low grade or marginal reserves into competitive reserves. 2) To increase yield and decrease costs. 3) To decrease investment. 4) To increase mine life. 5) To improve product quality to meet market demands. The very definition of frontier technology implies that it is so different that the old plant, if already in use, will not be directly suitable to use the new technology. Therefore, a priori, we know that the commercialization of frontier technology would very likely involve new investment. The recommended technique of economic and technical analyses, I propose to call "Success Analysis.'' Simply stated, it forces us, by step- by-step procedure, to ask "what is needed to succeed in this particular project." Therefore, the first step is to identify what is meant by "success." The definition of "success" requires an agreement with top management or sponsors of the project as to what constitutes "success" in their minds as contrast to the technical people perception of "success." In general, top management would define success as meeting: 1) The technical objectives, i.e., technology being developed would produce the desired product at the acceptable quality. 2) Financial objectives, i.e., when commercialized, the project's capital cost, operating costs and return on investment are better than the projects they would normally fund. The return has to be better because new technology is inherently riskier. 3) Marketing objectives in that the project will produce product of acceptable quality in timely manner, i.e., scale-up to commercial plant would not cause undue delays in start-up and that large fix-up expenditure would not be required to protect the projected return on the investment. Many projects are started in the laboratory to develop "Frontier Technology" in mineral processing. Most of these efforts are never commercialized. There are many causes of these failures. The major causes are listed below: 1) Inadequate communication with the sponsors of the project so that project objectives are defined and agreed to by all. 2) Ill-defined technical problems. 3) Incomplete development of technology. This has two major components: a. Incorrect scale-up and engineering. b. Inadequate start-up and maintenance planning. 4) Incomplete and over-optimistic process economics. 5) Lack of understanding of the future behavior of the marketplace. 6) Failure to complete R&D effort by the time it is needed. 7) Incorrect projections of human resources required; that is, technical, managerial and operating. 8) Lack of realistic forecast of the expenditures required for commercialization of the R&D effort. These pitfalls can be avoided by comprehensive planning and the use of success analysis technique. The major elements in "Success Analysis" are: 1) Identification of the "need" for new technology. 2) Unbiased and complete scale-up engineering. 3) Acceptable economic feasibility with enough margin of error in the sale prices and operating costs to justify the inherent risks in frontier technology. 4) Timing for availability of investment capital and markets. Many failures in the development of frontier technology are preordained because the initial selection of the research project has been without adequate attention to the needs of the industry. Many very innovative hydrometallurgical processes for recovery of copper from concentrates were developed in the past twenty years. They have not adapted except to a very minor extent because they did not satisfy the success analysis criteria. The copper industry in North America needed a process to compete against high grade ores and to avoid

Jan 1, 1985

By James R. Arnold

Gold Fields Mining Corporation started processing ore from it's Chimney Creek operation in northern Nevada in November, 1987. Since that time production has averaged about 200,000 ounces per year from the milling and dump leaching circuits combined. The events that led up to commissioning of the plant started in January of 1985 when the Gold Fields exploration team drilled their first hole in an area now known as Discovery Hill. The major orebody was located later in the year in what is currently the major focus of activity, the North Pit. Subsequent drilling since plant startup has found another 14 million tons of ore two miles south of the original orebody. This South Pit orebody is currently being stripped and metallurgical testing is underway. Engineering Engineering on the Chimney Creek plant started in earnest in May, 1986. Davy McKee Corporation from San Ramon, California, did both the engineering and the construction management. Before engineering began the entire senior staff of the Plant Department was hired and assigned to the project. Senior staff included the Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist. Gold Fields does not employ an internal central engineering staff to design their plants. We feel that the people who design the plant should be the ones who will be required to run it once it has been commissioned. This philosophy affords a continuous accountability from start of design through commissioning and operations. All four of the senior staff spent the most critical phase of the engineering stage at Davy McKee, so the plant is truly a reflection of all four disciplines. In bringing on the Maintenance General Foreman from the start, there was a focus placed on ease of maintaining the plant. Another philosophy that was adopted from the start was that the plant be easy to work in and maintain for both operators and maintenance personnel. Numerous design criteria were given to Davy McKee to ensure this. For example, we required that every piece of equipment could be reached easily with a crane or fork lift. All conveyors were required to have walkways on both sides for ease of maintenance and a minimum of 30 inches of clearance under them for ease of cleanup. Visibility for operators was considered very important and the control rooms and general plant layout were designed with this in mind. A list of about 100 general rules were given to Davy McKee during the early layout meetings and these were held as the general design criteria throughout engineering and construction. While engineering was progressing in San Ramon, California, dump leach test work was being done at the site. Three 6 foot diameter fiberglass columns were constructed and filled to a 20 foot height with low grade ore. Leaching characteristics were determined and the dump leach design was based on information collected from these columns. Construction The major contractors on the project were The Industrial Company for the bulk of the piping and structural, EMKO on the electrical/ instrumentation and Hunewill for most of the earth work and leach pad construction. All plant operating and maintenance personnel were employed eight weeks before startup for intensive training. Instructors were Gold Fields personnel, including foremen, and Davy McKee engineers. On occasion, selected suppliers representatives were brought in to discuss major pieces of equipment. Project completion was targeted for January, 1988 at a projected cost of 78.9 million dollars. Actual startup was about 1 1/2 months ahead of schedule and slightly under budget. Full design capacity was achieved the first full month of operation. Crushing Run of mine ore is delivered to the crusher and dumped into a 90 ton hopper which is topped with a 30" X 30" opening stationary grizzly. Ore is fed to a 50" X 60" Telsmith jaw crusher with a 5' wide apron feeder. The closed size setting of the

Jan 1, 1989

By J. B. Gwiazda

In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the .u factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the .u of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves.

Jan 1, 1987

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

By Mohammad Ranjbar Hamghavandi, Mohammad Ranjbar, Zahra Manafi, Mohammad Hassan Fazaelipoor, Mahin Schaffie

The present study introduces a new approach to understand the copper dissolution rate and to find an adapted mathematical statement for particle shrinkage rate in a batch bioleaching system. Four size classes of a chalcopyrite concentrate, namely [D1 : (−54 + 44)μm, D2 : (−44 + 38)μm, D3 : (−38 + 25)μm and D4 : (−25)μm], were used in the batch bioleaching tests by applying a mixed culture of moderately thermophilic microorganisms. The pulp density and temperature were 8 (%w/v) and 50 °C, respectively. Findings delineated that the bioleaching time can be divided into two specific time intervals: first, the surface reactions were the prevailing controlling step; second, the prevailing mechanism was diffusion through the product layer, whereas the overall rate of the process may be related to both through a Q factor using a mixed model. A mathematical model was developed based on particle size distribution (PSD) and a kinetic model. Experimental validation of the mixed model was accomplished by the representative sample with d80 = 54 microns. Results showed that the PSD of the specific sample was in good agreement with Rosin–Rammler function. Besides, the simulation result of the conversion fraction had the best conformity with the experimental data (with a maximum error of approximately 7%). This paper should be considered as an initial part of a larger, global model for chalcopyrite concentrate bioleaching.

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By Dal Negro Enrico, Andrea Picchio, Boscaro Alessandro

"The Doha Metro Project is one of the most relevant ongoing tunneling projects. The whole project consists of about 100 km of tunnels with 21 EPB TBMs working in the same period. Due to the variability of the geological formations, the soil conditioning is a relevant aspect of this project because the parameters should be frequently adjusted to achieve the best performances of the TBMs. The study of the soil conditioning has been carried out accurately to obtain the best results on site. The study of the geotechnical data, the choice of the most suitable foaming agents and polymers and the laboratory study of the soil conditioning has been a fundamental part of the job. The application of the soil conditioning products on site with the analysis of the TBM data have confirmed the preliminary study results with some correlation between the features of the ground and the soil conditioning parameters to be used. INTRODUCTION Phase 1 of the Doha Metro Underground project is composed by 3 lines able to bring passengers to all the points of interest in the Qatar capital city. The Red Line, also called coastal line, connects the north of the city to the south, and to the new Hamad International Airport, following the coast line. The Golden Line, called Historic Line, will connect the southern area of Doha to the “Aspire zone” the area of the city where many state of the art sport centers are located, passing through the old city center. The Green Line, named education line, will connect the old city center to the Doha Education City. All the lines are realized with 2 tubes, single track. The whole underground project is realized with 21 TBMs, excavation diameter of 7.10 m. The project has been divided in 4 packages, for a total excavation length of more than 100 km. The need to underpass roads, existing buildings, and to excavate, in some areas, at less than 100 m from the coast line, forced the choice of a tunneling system with Earth Pressure Balance (EPB), that involves in the project another fundamental aspect of this tunneling system: the soil conditioning. The soil conditioning has multiples functions in the EPB system such as to make the soil suitable to properly apply the pressure on the tunnel face and to be extracted effectively with the screw conveyor. To properly study this topic it was necessary to study the geological formations to be excavated, the hydrogeological conditions of the underground, the foam injection systems of the EPB TBMs and to perform specific tests to evaluate a suitable conditioning to be verified and adjusted during the real scale application."

Jan 1, 2016

By M. G. Skowroski, G. G. Eichholz, J. P. Ambrose

Introduction It has long been known that there are extensive deposits of phosphate-bearing deposits in the Coastal Plain of Georgia in many locations that are similar to those being mined commercially in central Florida. A major drilling program was conducted in 1966-67 by the Georgia Geological Survey (GGS). The economic potential of some of the material uncovered was evaluated at that time by a team at Georgia Institute of Technology led by Dr. J.E. Husted. There were some promising results. Since then, there has been little commercial interest in pursuing this matter, though the potential for development remains. In the long term, Georgia's phosphorite deposits could be a major source of income to the state if they were commercially processed. Phosphorite deposits contain significant levels of uranium and thorium. Uranium concentrations in Florida phosphate aggregates have been found to be 120 to 140 ppm. The presence of high concentrations of uranium means that there is a small but finite concentration of radium, which subsequently leads to radon gas emanation. It is the radon emanation and its progeny that may pose the largest health problem in many types of mining. Surface mining operations can possibly elevate the radon and radon daughter concentration in the vicinity. There is always some public concern whether any increase in the radon concentration in the atmosphere by mining (surface mining in the phosphorite case) could elevate the risk of cancer in the nearby population. At the present time, a great deal of attention has been devoted to the possible health effects of radon and its decay products in the inhaled air in mines and inside buildings built on mill tailings or uranium-bearing rock (Gesell and Lowder, 1980). Several evaluations have been published on the potential health effects of the Florida phosphate operations (Guimond and Windham, 1975; Roessler et al., 1980; Travis et al., 1979) and for buildings incorporating phosphate slag aggregates (Kahn, Eichholz, and Clarke, 1983; Roessler, Roessler, and Bolch, 1983). They all indicate that such potential effects are small, but tangible, compared with other radiation effects, for instance in the nuclear industry (Cohen, 1981). In view of the current concern, especially by the US Environmental Protection Agency (EPA), with the radiological consequences of large-scale mining of uranium-bearing phosphate rock (Guimond and Windham, 1975), it was decided to assess the potential radiological consequences if the Georgia deposits were developed. This paper presents an attempt to estimate the magnitude of any radon-based health effects that might arise from future mining operations in selected areas of the Georgia coastal region. To do this, a calculational model was developed that took into account the mining operations themselves, the atmospheric dispersion of the radon released, and the radon daughter concentrations in nearby towns. The model was applied to both extremes. The first application was a hypothetical mining operation in Echols County. Echols County is very sparsely populated and, unless living very close to the site, a person would probably experience little radiation exposure, if any. The model tries to prove this point. The second application was at a site near Savannah, Georgia. Both sites contain economically feasible phosphorite deposits and were not entirely hypothetical in that sense. Site selection In the course of the South Georgia Minerals Program (Furcron, 1967), an extensive series of drill core samples had been collected from various mineral occurrences in the coastal plain. It was found that the cores from the previous drilling program (Furcron, 1967), though carefully preserved, were not readily accessible. But the GGS reports did contain gamma logs of all the holes surveyed. With the cooperation of Dr. Neal Shapiro of the Survey, some core samples were selected and assayed, and used to calibrate the gamma log data. Samples from locations known to have detectable radioactivity were screened and counted. Their measured uranium content was used to calibrate the gamma log profiles for those same holes as obtained by the GGS. On this basis, two of the higher-level sites were selected and the calibration was used to obtain integrated uranium concentrations over the length of the borehole. It is customary to describe radon and radon-daughter concentrations in "working levels" (WL), where one WL represents a concentration of radon daughters capable of releasing 130 000 MeV of alpha particles, equivalent to 100 pCi of radon in equilibrium with its daughters per liter of air. A representative concentration is 0.15 WL, below which radon levels are widely considered to be negligible. For the mine sites selected, the surface area and rock volume were determined to estimate their radon content. Working-level values were then estimated for the assumed radon release from the crushed ore and the exposed surfaces of the mine pit. According to Kisielewski (1980), 93.4% of all radon released from open-pit operations is released from the ore zone; thus, the calculations assumed that those surface areas were the main sources.

Jan 1, 1987

By Haydn H. Murray, Fred G. Heivilin

The "Hormite Group" was proposed for palygorskite (attapulgite) and sepiolite for their complex magnesium silicate composition and elongate crystals (Martin-Vivaldi and Robertson, 1971). These minerals occur in close association with each other and more complex structural variations may exist (Bailey, 1972). In 1862 Savchenkov used the name palygorskite to describe a mineral from the Palygorsk locality (Hay, 1975), near the Ural Mountains. Ovecharenko and Kukovsky (1984) mention that when mountain leather deposits were prospected in the Palygorsk Division mine it was assumed this unusual mineral was a variety of asbestos. Early mineralogists used the terms "mountain cork" or "mountain leather" when referring to palygorskite. Robertson (1986) mentions that it appears palygorskite was known since Theophrastus&apos; time, ca. 314 BC. J. de Lapparent used "attapulgite" for clays from Attapulgus, GA, and Mormoiron, France, because he thought them different from palygorskite, but the two types were proved to be the same (Bailey et al., 1971). The name attapulgite is still used for the Florida and Georgia deposits when the crystal length to diameter ratio does not exceed 10:1(Merkl, 1989). Georgia palygorskite clays are of much shorter length compared to classic palygorskite. In 1847 Glocker first used the name sepiolite which was called "Meerschaum" by Werner (1788) and Hauy (1801) namedit "Ecume de Mer." Brochant (1802) described low density and white magnesium silicates adding the name Talcum Plasticum and Ecume de Mer. In the Meigs-Attapulgus-Quincy district palygorskite (attapulgite) commonly occurs in two distinct forms referred to as short length palygorskite (Meigs Member) and long length palygorskite (Dogtown Member) (Merkl, 1989). Long length palygorskite crystals (> 10 pm) are rarely observed in the Meigs and Dogtown Members, but when present are in association with dolomite crystals. The short length form is usually less than 2 pm in length and has a low magnesium content whereas the long length form has a high magnesium content and a length greater than 2 pm. The distinctions in morphology are not only important because of the relationship to the origin of the deposits, but also in relation to activity in causing membranolytic activity related to data on palygorskite samples from 9 locations ranging from relatively inert to active in work reported by Nolan et al. (1989). The > 10 pm lengths amounted to only 51 of 17,401 fibers sized. The shortest lengths (< 0.5 pm) were relatively inert. This study pointed out that surface activity, morphology, and chemical differences may be distinctly different within the definition of palygorskite, or for that matter for any individual mineral so that health and other properties must be measured because the name alone does not necessarily indicate uniformity. Palygorskite (attapulgite) fuller&apos;s earth was first sold for drilling mud in 1941. The market for this use expanded slowly and has maintained a level of 7 to 10% of the total US production during the last few years. Most of the fuller&apos;s earth sold for drilling mud comes from the southern part of the Meigs-Attapulgus-Quincy district of Georgia and Florida. Palygorskite clays produced in this area are superior to most other fuller&apos;s earth for mud used in drilling salt formations, but because of high water loss, they are inferior to bentonite where the rocks drilled contain no saltwater. According to Oulton (1965), more than 90 different grades of fuller&apos;s earth are produced. Some of these grades are used for pharmaceuticals designed to absorb toxins, bacteria, and alkaloids; for treatment of dysentery; for purifying water and dry cleaning fluids, dry cleaning powders and granules; for the manufacture of NCR (no carbon required) multiple copy paper; for the manufacture of wallpaper; and as extenders or fillers for plastic, paint, and putty. Fuller&apos;s earth mined near Ellenton, FL, was used for making lightweight aggregates for the construction of concrete barges during World War I1 (Calver, 1957). Still other uses of fuller&apos;s earth and its suitability for uses in new products are outlined by Haden, Jr., and Schwint (1967), Haden, Jr., (1972), and Haas (1970). One special use of fuller&apos;s earth is as a carrier of platinum catalysts that are made in the United Kingdom from sepiolite clays mined in Spain. Other uses of sepiolite fuller&apos;s earth (Chambers, 1959) are similar to those of the palygorskite (attapulgite) type mined in the United States.

Jan 1, 1994

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O&apos;Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By T. P. Lim, J. A. Cherry, A. J. Vivyurka, R. D. Blair

The first phase of an investigation of the chemical composition of subsurface water and the hydrochemical processes in and near the abandoned Nordic tailings at Elliot Lake, Ontario, was conducted in 1979. The Nordic area, which covers 85 hectares with an average thickness of 10 m and overlies deposits of permeable glaciofluvial sand, contains 15 million tonnes of tailings with 4-7% pyrite. Nests of standpipe piezometers installed at three locations on the tailings indicate that seepage through the tailings is predominantly downward. The water table in the tailings slopes from the north side of the tailings dam, where it is within a metre of surface to the south side near the tailings dam, where it is approximately 10 m below surface. When they were deposited during the period from 1957 to 1968, the tailings contained pore water at a pH of about 8 resulting from neutralization treatment in the mill. At the three piezometer nests, the pH increases from 3 near the water table to 7 near the bottom of the tailings. The pore water in the tailings is gradually becoming acidic because of oxidation of pyrite in the zone above the water table. The concentrations of Fe, Mn, Ni, Co, Zn and Pb are high in the shallow acidic zone and much lower in the deeper neutral zone. Concentrations of 226Ra range from 30 to 230 pCi/L. At the three sites concentrations of major ions in the permeable sand a short interval beneath the tailings indicate 226Ra presence of tailings seepage, but Ra concentrations are only 2 to 8 pCi/L. Greater downward penetration of 226Ra probably occurs in the area closer to the tailings dam. Monitoring of a network of multilevel bundle piezometers installed in permeable sand that extends southward from beneath the tailings indicates the occurrence of a plume of tailingsderived water containing high concentrations of Ca, Mg, Fe and S04 that extend 400 m downgradient from the tailings dam. The total dissolved solids decline from 20,000 at the dam to less than 500 mg/L at the identifiable downgradient periphery of the plume. A much smaller but distinct plume of water with high heavy metal concentrations and 226Ra in the range of 10 to 130 pCi/L extends from beneath the dam for a distance of 15 m. The pH of the groundwater in this heavy metal-radium plume is 4 to 5, whereas elsewhere in zone of groundwater with high dissolved solids, the pH is above 6. The results of this investigat, suggest that the heavy metals an 226 Ra are relatively immobile in the perme-

Jan 1, 1980