Search Documents

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By Eli Curiel, Ingar F. Walder, Patrizia P. Schuster, Walt Keyes

Mansfield Canyon, of the Wrightson Mining District, Santa Cruz County, Coronado National Forest, Arizona, was actively mined in the late 1800's and early 19001s, with minor activity until 1953. The main products were lead, silver, copper, zinc, and gold occurring in polymetallic quartz veins. The canyon contains numerous adits and waste dumps, some of which generate metal-loaded acid. Samples of seeps, waste dumps and bedrock have been collected for various analyses: metal concentrations, acid base accounting (ABA), and water quality to evaluate the extent of oxidation and metal release from the start of mining until present, the potential impact, and reclamation options. Although the waste-rock piles within the canyon are small (2,000-10,000 tons), they have a high sulfide content with little or no neutralizing capacity. It is planned, therefore, to move the waste piles either to a constructed repository site within the canyon or to a copper leach facility to be used as an acid generator.

Jan 1, 2000

By C. Milne, T. M. Dyhr, T. E. Wilson

As time progresses, new concerns regarding long-term post-mining effects are identified, increasing mine closure costs. Regulators responding to public interest must take a “worst case” view and require post-closure monitoring or remediation processes. Although closure costs depend on the size and type of operation, general cost categories are defined, and median values (per acre, or per unit of production) are identified. Closure cost categories, as well as amounts, have increased with time. Except for increased efficiency in earth-moving and water management (surface or subsurface), there are no apparent offsets to a steady rise in closure costs. When the historical trend of closure costs is considered, it is probable that additional cost categories will come into being. For mine operators, the challenge will be to anticipate them and devise cost-effective remedies.

Jan 1, 2003

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Robert Sutton, Milan Sjaus

Conveyor pulleys are an important and integral component of a conveyor. Conveyors work in sequence to make up conveyor systems. Each conveyor system is only as reliable as its crudest component. If the pulley fails, then the whole material handling system stops. So what is the effect of this downtime? What are the costs of repair? How much are we willing to pay to solve the problem? What should we spend to prevent an unscheduled shutdown? Do we use the technological improvements at our disposal or do we ignore them to satisfy immediate cost savings? This study will focus on the cost of pulleys relative to the total conveyor cost, the cost of downtime, the maintenance costs and the costs for resolution of the problem. Some philosophic and design concepts are injected for illustration and discussion.

Jan 1, 2000

By Todd L. Hollingsworth, Jeremy K. Hobbs

In 2001, the Radomiro Tomic Mine located near Calamq Chile, added a tertiary crushing facility. An 84" wide mobile tripper is used to fill their tertiary crushing storage facility. This paper is a we study to demonstrate the drive and control systems in use on the tripper. Of special note is the design concept used to allow the system to operate multiple motors in both demand and regenerative modes through a single VFD. Also noted is the use of touch screen local controls, handheld radio controls, starting/stopping/ braking philosophies, safety device interfaces, and the local to remote control interface.

Jan 1, 2004

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The term unsaturated flow refers to the conditions in which soil pores are filled partially with water and partially with air. This situation constitutes a porous material filled with immiscible fluids. Immiscible fluids by definition exhibit a distinct interface when in contact with each other resulting in a pressure discontinuity across the interface due to surface tension. The fluid that tends to wet the solid particles is called the wetting fluid and the other is the nonwetting fluid. In the air-water sys- tem, air is the nonwetting fluid and water is the wetting fluid. A somewhat analogous fluid system is that in a petroleum reservoir in which there may be up to three immiscible fluids-oil, salt water, and natural gas. The degree of wettability of the fluids is salt water + oil + gas. That is, salt water is the wetting fluid at any interface and oil is the wetting fluid at an oil-gas interface but is the nonwetting fluid at a water-oil interface. Since the oil-water and air- water systems are similar, much of the theory and methods of analyses for the air-water system or unsaturated flow have evolved through the petroleum literature. In the two-fluid system the pressure difference across an interface depends on the size of the pore space in which the interface occurs. The equation commonly used to represent this dependence is

Jan 1, 1986

By W. S. Fyfe, G. Southam, T. J. Beveridge

Sporosarcina ureae was able to grow in the presence of tip to 10-ppm L-asparagine complexed gold. However, 10 ppm Au3+ was found to be highly toxic to Sporosarcina ureae, killing 109 bacteria/mL within a few seconds. To compare the effects of these responses on gold mobility, an in vitro bacterial biofilm model was developed to examine the interaction be¬tween Sporosarcina ureae and ionic gold or L-asparagine gold complexes in gravity fed columns. The immobilization of ionic gold was between 80% and 90% over a period of one week. But, as the available cellular reactive sites became saturated, immobilization decreased to 14% within two weeks. In the L¬asparagine-gold system, gold immobilization in the cytoplasm occurred at a high rate (80% to 90%) throughout the experi¬ment, with limited toxicity towards Sporosarcina ureae. The bacterial immobilization and detoxification of L-asparagine¬complexed ionic gold was associated with a low molecular weight, i.e, <5,000 dalton (atomic mass unit), intracellular protein fraction. This peptide-complexed gold would allow for the continued biogeochemical cycling of gold under ambient (<100°C) surface or near-surface conditions.

Jan 1, 2000

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995

By Robert A. Haney

Utilizing the recently developed laser velocimeter and a Pitot-static tube, the United States National Bureau of Standards (NBS), has calibrated various types of anemometers that are commonly used in the mining industry. This paper presents a summary of the performance characteristics including accuracy, precision, starting and stopping speeds of each instrument tested. The specific instruments that were calibrated by NBS have become Mine Safety and Health Administration (MSHA) primary reference instruments. These primary reference instruments are used in turn to calibrate secondary reference instruments for each Coal Mine Safety and Health District. Each District calibrates anemometers that are used by District engineers and inspectors. Calibration is accomplished through a substitution procedure in which the reading on the anemometer is compared to the true velocity determined by the reference instrument. Calibration is performed over the entire range of the instrument using an open jet wind tunnel to produce the various approximate velocities. Some specific details of the calibration procedure are presented in this paper.

Jan 1, 1980

By D. W. Fuerstenau

The success of industrial flotation separations has been the design of specific chemical schemes for regulating the bulk and the surface chemistry of the system. Highlights of fundamental research on the nature of flotation reagents and their mode of action in flotation, which has been carried on for about the past 65 years, is briefly reviewed.

Jan 1, 1995

By J. G. Henning, R. Edrissi

This paper describes a practical methodology, based on numerical modeling, for the prediction of progressive failure of underground-mine stopes having cable-bolt support. A case study of the 40-761 scope at the Kidd Creek mine, Timmins, Ontario, Canada is presented. Scope 40-761 was mined by blast hole open sloping in 1986 and was a lead scope within a mining block located between levels 36-1 and 38-2. Initially designed to peak at level 38-2, the scope back caved upwards =40 m towards level 36-1. After caving began, cable bolts were installed above the stope from level 36-1. The stope eventually stopped caving when the falling rock mass encountered a sufficiently high cable density. This paper provides details of the geomechanical data and modeling results of the case study. Numerical modeling of cable bolts around the mine stoke was carried out using a finite-element modeling software. The software, known as e-z tools, was developed by the first author.

Jan 1, 1996

By J. M. Kruger

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially-intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite&apos;s mushroom-shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1997

By Lynn B. Hales, Randy Ynchausti, Jeffrey D. Mckay

Many consider rougher flotation control to be more of an art than a science. Some have even thought it impossible to make process control decisions and changes without human interaction. Controlling flotation bank pulp levels to maintain consistent pulling rates in the face of changing feed slurry flow rates, varying mineral types, and inconsistent reagent additions can be daunting. However, an advanced supervisory control strategy was installed on the plant floor to control an industrial rougher flotation circuit with little or no operator interaction. Plant staff monitored the flotation circuit under supervisory control and reported benefits of up to 4% improvement in copper recovery above that achieved with an older supervisory control strategy. To accomplish this work, a novel use of instrumentation to solve a flotation bank pulp level control problem was employed, a new implementation approach was used to correct some flaws in the older approach, and careful attention was paid to a few key process control principles. This paper discusses important aspects of these activities.

Jan 1, 2000

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By Gordon M. Elliott

Health risk underlies all of today&apos;s environmental regulations. Mine Manager&apos;s are no strangers to risk, but risk in the context of mine management is not the same as risk in the context of environmental regulation. One of the risks facing the mine manager is whether the mining operations meet environmental compliance standards. These standards are defined in terms of the frequency of occurrence of adverse health effects in an exposed population (i.e., health risk). Demonstration of compliance necessarily involves mathematical modelling and selection of values for input variables. What is not immediately apparent is that the method of estimating the human health risk has a significant influence on remedy selection and the amount of money spent at suspected contaminated sites. Using a hypothetical, mining-related example, this paper illustrates the disassociation between the current deterministic approach to health risk assessment and cost-effective decision making. This paper also illustrates how the probabilistic approach to health risk assessment provides a more realistic characterization of health risk and enables mine managers to identify cost-effective remedial strategies for the site.

Jan 1, 1992

By Brian K. Failon

Scale formation is a problem that affects many mineral processing systems because the processes require the use of large volumes of water. Scale composition may vary from circuit to circuit, but the scale deposition mechanisms and needs for prevention are often somewhat similar. Likewise, there is a degree of commonality in the prediction, detection, and elimination of scaling conditions in various water systems. This paper briefly reviews some of the conditions which lead to scale formation, as well as some of the common problems associated with unchecked scale growth. The primary focus of the paper is on the variety of chemical scale inhibitors available for use in mineral processing circuits, and the actions of each type. The means of predicting and detecting scaling tendencies are also addressed, and include both direct and indirect methods, i-e., stability index determination and chemical analysis of deposits.

Jan 1, 1986