Search Documents

By Bahne C. Cornilsen, X. Shan, David H. Carlson, John H. Johnson

The air in three U.S. underground coal mines has been sampled. The data developed show the relative importance of the various pollutants and quantify the need for control. Total respirable particulate matter (TRPM) was found to be the critical pollutant (the one requiring the most dilution for control). TRPM is considered to be "respirable coal dust" by procedures approved for sampling in U.S. underground coal mines. However, this "respirable coal dust" also includes diesel particulate matter (DPM) and particulate from other sources. While "respirable coal dust" was the critical pollutant, Raman spectroscopic analysis showed that more than half of this "respirable coal dust" was DPM. The DPM in the samples ranged from 22 to 152% of the 2 mg/m3 limit for respirable coal dust. Thus DPM was the critical pollutant using the 2 mg/m3 respirable coal dust limit. SO2 gas produced by the combustion of diesel fuel containing sulfur was the second-most critical pollutant. Characteristic curve slope (CCS) values were calculated to determine the quantitites of the various pollutants generated per unit of diesel haulage activity. Mine 1 had the highest TRPM CCS values with 29 mg/m3/%C02 for the Ramcar and 57 mg/m3/%C02 for the Haulageway location. The highest coal particulate CCS measured was 30 mg/m3/%CO2 and the highest diesel particulate CCS measured was 27 mg/m3/ %C02. Both of these high values were measured in the Mine 1 haulageway location. Calculations were made to determine the controlling CO2 concentrations (CCC) at which all other measured pollutants would be within their limits. These CCC values, which, for the mines sampled, were based on TRPM, varied from a low of about 0.07% for the Mine 1 haulageway location, to a high of about 0.15% for the Mine 2 Ramcar and haulageway locations. Weekly average CO2 concentrations measured in these mines ranged from 0.09 to 0.11 % for the Ramcar, from 0.05 to 0.09% for the haulageway, and from 0.08 to 0.11 % for the return. The concentrations of TRPM ranged from 1 and 2 mg/m3 in mine areas frequented by personnel, and to greater than 4 mg/m3 in returns where personnel are not exposed.

Jan 1, 1991

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By R. C. Emmett

Gravity sedimentation is one of the most widely used unit operations in mineral processing and hydrometallurgy. Properly selected and operated sedimentation equipment can provide probably the most economical means of concentrating solids or clarifying solutions. Because of the variety of different approaches possible, including the use of modern flocculants, it is easy to overlook the optimum approach in selecting equipment. The different types of sedimentation systems that can be used in the minerals field and the sizing methods that are currently employed will be discussed here. Sedimentation applications usually fall into two areas, clarification or thickening. While the two operations are basically similar, the difference in emphasis (a well-clarified overflow as opposed to a highly concentrated underflow) results in significant differences in testing, equipment design, and operation. Clarifiers may be merely simple settling vessels with no special features, other than ample volume to provide the detention time needed for suspended solids to settle out of the feed slurry. Or, they can be designed to employ elaborate solids-contact techniques utilizing coagulants or flocculants to achieve more rapid clarification through the growth of particle agglomerates. Thickeners also are available in a wide variety of designs, with the main differences concentrated in the design of the raking mechanism. Thickeners operating in series (continuous countercurrent decantation or CCD) are used to recover valuable solution or purify the insoluble solids. Tray thickeners are used for recovering fine particulate solids such as alumina seed, but in other applications have been supplanted largely by unit thickeners or inclined plate units. Thickeners and clarifiers sometimes are used for storage of either solids or overflow liquor, or employed as precipitating reactors, such as in desilication applications. The use of flocculants and coagulants is much more common in modern processing plants, primarily due to the reduction in capital costs rendered possible through the use of these reagents. The terms flocculant and coagulant are often used interchangeably; generally, it is understood that flocculants refer to organic, high molecular weight synthetic or natural polymers which are useful in flocculating most suspended solids, but generally are ineffective on colloidal suspensions. Coagulants refer to chemicals such as those commonly used in water treatment, alum, ferric salts, lime, etc., which are usually far more effective on colloidal solids but cannot achieve the degree of agglomeration that is possible with the polymers. In some cases, both coagulants and flocculants are used in order to achieve optimum results.

Jan 1, 1986

By John W. Rushton

Maintenance and inventory are usually the last items considered in mine development. They need to be addressed properly and early. The micro-computer brings sophistication within the reach of even the smallest mines. Maintenance and inventory programs, if properly installed, will reduce costs 15 to 25% and allow management time to address the mining and metallurgical problems at start up. Shops and warehouses are rarely designed properly. Large engineering firms spend 5 to 20 times more than is necessary for first class facilities. There is an optimum design, size, and layout. Take the time necessary to assure you get the right people, programs, and facilities in that order. Maintenance, inventory, and inventory control must be addressed early if a small mine is to have a chance at optimizing costs during the first two years of operation. This is hard work and is usually put on the back burner until the mine is in some degree of trouble. Hiring an experienced maintenance superintendent is important but it is not the complete solution. Maintenance systems, design of facilities, and use of computers are not skills that maintenance people usually have. In addition, the work of ordering spare parts and working with erection people is a full time job and any maintenance people on site during construction are quickly recruited. The end result is that few mines start up with an adequate Maintenance or Inventory System in place. The months, and in some cases years, that the mine attempts to operate without a system are both painful and expensive. Designs of successful integrated maintenance and inventory programs are virtually 100% supported with some outside assistance. Our system is the approach that we are most familiar with and this paper will isolate how Rushton International would go about setting up systems and designing support facilities. Micro-computers are the only way for a small mine to go. ~ini-computers cost more originally and operating costs are many times higher than even the most sophisticated micro system. Micro- computer software is developed further and recent advances in hardware makes medium priced units equal to most mini's in RAW COMPUTER POWER. Mines in general, and especially small mines, have no need for main frame power. MAINTENANCE A good maintenance program has: 1. Equipment Master List a. Equipment Detail Reports 2. Work Order and Backlog Control Program 3. Component Control Program 4. Tire Program 5. Wear Materials Program 6. PM Control Program 7. Maintenance History Program 8. Performance Program We also track miscellaneous items such as MSHA training and inspections, timekeeping, etc. Rather than going through the program step-by-step, it makes more sense to go through a typical Maintenance Day and show how the programs are used. The first thing maintenance supervision needs to know is "how we are doing." We

Jan 1, 1987

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: 1) as a diverse group of fine-grained minerals, 2) as a rock term, and 3) as a particle size term. As a rock term, clay is difficult to define because of the wide variety of materials that comprise it; therefore, the definition must be general. Clay is a natural, earthy, fine grained material comprised largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates comprised mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic, e.g., halloysite and flint clay. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 pm. as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 pm. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1988, 1989, and 1990 productions according to the US Bureau of Mines (Ampian, 1992). As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this section these commodities are organized as follows: 1) bentonite, 2) common clay, 3) hormites, and 4) kaolin. Fuller's earth is discussed in both the bentonite and hormite chapters. Fuller's earth is a term based on use, and both bentonites and hormites are sold as fuller's earth. The overlapping is particularly evident where both bentonite and non-bentonite fuller's earth are used for the same purposes or products, such as in drilling mud, bleaching or clarifying fats and oils, and carriers for insecticides and fertilizers. Kaolin, ball clay, halloysite, and refractory clays are grouped together because they consist mainly of minerals of the kaolin group. Common clay is a grouping of several fine-grained materials, including shale, sometimes referred to as miscellaneous clay. The scientific and technological publications pertaining to clays

Jan 1, 1994

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam&apos;s operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer&apos;s Office and in accordance with recommendations in a report done for the Corps of Engineer&apos;s Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By M. Kung, D. Schwegler-Berry, V. Castranova, D. Lewis, H. Abrons

Pulmonary responses to coal mine dust exposure were investigated by analysis of bronchoalveolar lavage specimens from non-smoking coal miners (n-12, mean age-43 ± 2 years, mean underground exposure-17 ± 2 years) and from non-smoking normal volunteers (n-18, mean age-43 ± 2 years). Spirometric and diffusion capacity indices were monitored as part of a physical exam. Lavage was performed in a subsegment of the right middle lobe by instillation of 200 ml of warmed saline solution in 50 ml aliquots and recovery by gentle suction. Specimens were centrifuged at 500g for 5 minutes at 2°C. Total and differential cell counts were recorded. Secretion of oxidants measured by chemiluminescence, surface morphology (spreading and ruffling), and lymphocyte parameters were determined. Lavage fluid was analyzed for the presence and quantity of acute phase reactants and immunoglobulins. Pulmonary function measurements as well as recovered lavage volume, total lavagable cells, and differential cell counts were similar in both miners and controls. Both resting and phorbol myristate acetate-stimulated chemiluminescence were also similar in miners and controls. In contrast, particle-stimulated chemiluminescence was significantly decreased in the alveolar macrophages from the miners (48% of control values). Morphometric analysis of scanning electron micrographs indicate that phagocyte surface spreading was similar in miners and controls. However, surface ruffling was 127% greater in the miners compared to controls. Lymphocyte subpopulations were similar in miners and controls. Protein analysis of the lavage fluid revealed lower total protein content in the lavage fluid of miners. However, the concentration of albumin, IgG, and IgA were similar in miners and controls. We conclude that most indices were normal in underground miners working under the current dust standard of 2 mg/m3. The decrease in particlestimulated chemiluminescence and the increase in surface ruffling in miners may suggest the beginnings of particle overload and activation of the macrophages. In addition, a decrease in total protein was noted in lavage fluid from miners.

Jan 1, 1991

By Richard M. Bennett

Twelve linear test foundations were constructed over an advancing longwall panel in southern Illinois, six were located along the centerline, and six in the maximum tension zone. One footing in each set was a control foundation constructed according to conventional practice. It suffered severe damage. Footings with reinforcing bare and post-tensioning had much smaller elongations, with the post-tensioning preventing cracking of the footing. Footing-soil interface treatments of plastic-on-sand and plastic-on-soil served to reduce damage. The addition of steel fibers to the footing had about the same effect as an interface treatment. Sill plate construction (butt-jointed versus lap-jointed) appeared to significantly affect the behavior.

Jan 1, 1986

By V. S. Znamensky, R. V. Stewart

This chrysotile asbestos ore body is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 miles) north of Montreal, 480 km (300 miles) north of the tree line, and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1% mile) in length, some 61 m (2OO ft) in width and plunges at 25o to 30 o below surface to a vertical depth of at least 610 m (2000 ft). The ore body was originally evaluated by programs of surface mapping, diamond drilling, and bulk sampling. The fiber is semicrude, possesses excellent strength, and good fiber length distribution. GEOLOGICAL SETTING, LOCATION, AND DISCOVERY The chrysotile asbestos mineralization at the Asbestos Hill mine occurs in serpentinized ultrabasic rocks of Precambrian age. These intrusive rocks are found in older volcanic sedimentary rocks known as the Cape Smith-Wakeham Bay belt and are shown in Fig. 1. The rocks comprising this belt overlie older basement rocks composed of granite and granite gneiss. This belt has a width of 32 to 64 km (20 to 40 miles), and trends in a general east- west direction, a distance of about 370 km (230 miles) from Wakeham Bay on the east coast of the Ungava Peninsula to Cape Smith, located on the east side of Hudson Bay. Two sequences of rock have been recognized in this belt. The lower (oldest) rocks are known as the Povungnituk group, and consist principally of massive lavas and sediments. The upper (younger) rocks are known as the Chukotat group, and are composed of pillowed lavas with interbedded sedimentary rocks. Sills of ultrabasic rocks exist in both younger and older rocks, but are more often found in the Povungnituk group. Concentrations of chrysotile asbestos, as well as nickel and copper minerals are found at or near the base of ultrabasic sills, and are most common where a change in dip occurs. The mine is situated about 1818 km (1130 miles) north of Montreal, approximately 1126 km (700 miles) north of the start of continuous permafrost, and about 482 km (300 miles) north of the tree line. The depth of permafrost at the mine site has been calculated to be approximately 549 m (1800 ft). This rich deposit of asbestos was discovered in 1957 during extensive exploration for nickel in the Ungava nickel belt. During that year, traverses conducted by Murray Watts spotted interesting looking ultrabasic rocks, and followup ground examination disclosed rich surface showings of asbestos mineralization near the present open pit. In 1958, a two-man prospecting party returned to the discovery site and a mineral exploration license was granted to Fig. 1. Location map Keewa Quebec Mines Ltd., a wholly owned

Jan 1, 1986

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV&apos;s) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV&apos;s. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman&apos;s daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today&apos;s highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.&apos;s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative&apos;s 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By L. G. Stolarczyk, R. C. Fry

In coal-bearing formations, seams are often bounded by sedimentary layers of mudstone, claystone or shale. When the electrical conductivity of the surrounding sediment layers is greater than the conductivity of the seam, a natural parallel plate waveguide forms in the strata. For frequencies below the AM broadcast band, the waveguide can be used for the transmission of electromagnetic (EM) waves. In a uniform seam, the primary wave travels in the coal layer along paths between a radiating antenna and a distant receiving antenna. The travel distance increases with seam height and the conductivity of the surrounding sediment layers. The distance decreases with increased coal conductivity. In Cretaceous western bituminous coal, the distance may exceed 549 m (1800 ft). Anomalous geologic disturbance zones such as faults, shear zones, paleochannels, sills and dikes significantly alter the values of EM wave propagation constants (attenuation and phase) expected in a uniform seam. In the neighborhood of an anomaly, EM wave energy is scattered (reflected and diffracted). Scattering creates secondary waves in the seam wave guide. A receiving antenna at a remote location in the coal seam can be used to measure the magnitude and phase of the EM wave at the end of the path. The measured data can be processed to determine the average value of the propagation constants along each path. Paths with anomalous propagation constants are used to locate and image geologic disturbance zones. Radio Imaging Method (RIM) instrumentation, survey procedures and data processing (tomography) algorithms have been developed to image geologic structure in advance of mining. The survey is conducted between gate roads of a longwall panel. Data processing constructs contours of constant attenuation rate (phase constant) across the plan view of the panel. In anomalous zones, the contours rapidly change with distance. The shape of the contour lines generates a visual image of the anomaly and suggests the type of anomalous condition to be expected in the coal seam. This paper briefly discusses the depositional environment and the formation of the imperfect waveguide in coal-bearing strata. The linkage between sedimentary geology and EM wave theory establishes an understanding of how the propagation constants depend on the anomalous geologic conditions. A case study compares in-mine geologic mapping with the tomographic image of a longwall panel.

Jan 1, 1991