Search Documents

By Linda K. Killoran

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomographic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First¬arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Y. Luo

An extensive subsidence research program conducted by the authors has greatly improved the accuracy and the capabilities of subsidence prediction under complicated mining and surface conditions. The techniques developed for assessing and mitigating subsidence influences on various surface structures have been applied in numerous cases with a very good re- cord of success.

Jan 1, 1997

By Steve P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39 instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6 m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor varia¬tions in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

Jan 1, 2001

By Christopher Phillips

In light of recent events in the mining industry, there has been an increasing demand for technology to detect underground voids and abandoned mine workings. This paper summarizes the use of geophysical methods for this application. Geophysical methods have been successfully employed in the detection of underground voids in several disciplines, including foundation analysis, road and infrastructure analysis, and darn analysis, but is not yet being widely employed by the mining industry. The principal reasons are that the combination of the complex geological setting of a mine, mine design, surface conditions, and improper choice of geophysical method often makes the task of locating abandoned mine workings with geophysics a frustrating, time consuming, and often unsuccessful venture. While there are several geophysical methods that have been demonstrated for the successful detection of abandoned mine workings, there is still no 'silver bullet' to solve the problem in every case. The choice of geophysical method to detect abandoned mine workings should be made on a site specific, and sometimes target specific, level. This paper reviews current methods, and introduces recently developed methods, for the detection of underground voids and abandoned mine workings.

Jan 1, 2003

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By Thomas L. Hutchinson

The mechanical design of a roof support is basically a matter of a statics and dynamics problem, assuming of course, that the imposed loads and mining conditions are known. Here in the Appalachian coal fields the general conditions are known well enough to allow the majority of the proposed new faces of longwall to be furnished with standard commercially available supports equipped with suitable variants and options. While not trying to negate the primary importance of thoroughly investigating a potential face and the selection of the correct equipment for that face, it still becomes clear that an equally important aspect of the design of an adequate ground control program has in the past too of ten been overlooked, having been overshadowed by the ?endless? selection process of the roof supports proper. The equally important aspect which this paper discusses is the overall design of a mining system, which design incorporates not only the size and capacity of the equipment but the following points as well, namely: Equipment adaptability to mining scheme, Equipment va. human constraints, Operation at the designed levels, and Coordination of operation, maintenance and support design. Unless the coordination of these factors is considered in the design and selection of the equipment, a lopsided and inefficient operation is possible. How can we afford to put an 8-10 million dollar investment up to chance as to whether it will yield optimum results or not?

Jan 1, 1981

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSI-I), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the root and Moor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right minethrough and should provide beneficial case study information fur other longwall backfilling applications in the future.

Jan 1, 1998

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration's (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990