Search Documents

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer's inventions in the 1850's as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950's and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850's, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

By Liming Wang

One of the steps in the extractive metallurgy of lead is a refining process called drossing. Hot dross is mixture of impurity compounds that form on the surface during the cooling of lead blast furnace bullion, and in Missouri, the main impurities are copper and sulfur. The slow cooling of bullion throws out of solution all other minor impurity elements (or their compounds) which are much less soluble at lower temperatures (mainly nickel, arsenic, iron, and zinc). The transfer of bullion from the blast furnace to the refinery and the subsequent hot drossing step cause fugitive emission of lead-containing fume and dust, which creates a plant hygiene problem. One cause of the emissions is the high vapor pressure of lead and its compounds during transmission of = 1000 °C bullion to the drossing kettle. Another cause is the lifting of dross dust during manual skimming of dross. The environmental problems associated with the traditional hot drossing process provided an incentive to investigate a new drossing process that avoids contact between plant air and hot bullion or dross. A key aspect of the process development was a detailed mineralogical examination of dross from two different bullions. The bullion samples were cooled at different rates, and the dross filtered out and examined. The morphology, phase identification, and composition of the dross was examined by optical and SEM microscopy. The principal dross phases were copper and cuprous sulfide, galena, a complex sulfide containing copper, nickel and lead, and speiss (containing nickel, cobalt, iron, copper, lead, and arsenic compounds). The copper was acicular, with nickel and arsenic in solid solution. The cuprous sulfide was largely digenite in a granular or dendritic form. A substantial part of the dross was solidified matte with a eutectic microstructure, consisting mainly of CU2S and PbS. Small particles (some of which had a eutectic microstructure) never floated to the surface of the lead during the slowest cooling rate, thus indicating that flotation of tiny matte droplets and dross crystals is exceedingly slow. The success in separating dross and lead by centrifugal filtration suggests its application in industry as a replacement for traditional hot drossing.

Jan 1, 1995

By P. Chris Pistorius

An example is presented to illustrate the joint effect of local reaction equilibria and mass transfer limitations, for reactions during ladle refining of steel. The example relies on some of the kinetic principles that David Robertson has employed to quantify many metallurgical processes. In calcium treatment of alumina inclusions in aluminum-killed steels, solid CaS forms as an intermediate reaction product. During subsequent reaction, CaS disappears and calcium aluminate forms; at the same time, aluminum and sulfur dissolve in the steel. Kinetic analysis shows that the rate of this reaction is not limited by mass transfer of dissolved aluminum and sulfur away from the reacting inclusions. The reaction rate is likely limited by transport of dissolved calcium. This example also illustrates the use of FactSage macros for kinetic modeling.

Jan 1, 2014

By P. A. Metz

The Fairbanks mining district has produced in excess of 7.5 million troy ounces of placer gold and 250,000 troy ounces of lode gold since gold was discovered in the area in 1902. The Fairbanks mining district is in the northwestern part of the Yukon-Tanana Upland Schist Terrane, an area of approximately 240,000 square km that has produced in excess of 21 million troy ounces of placer gold. All lode gold production from the terrane has been from the Fairbanks mining district, and all of this production has come from high-grade gold-quartz polymetallic sulfide veins. Gold grains in the vein systems range in size from several microns to several millimeters. The veins are localized in a complex metamorphic rock assemblage which includes greenstones and felsic metavolcanic and volcaniclastic rocks, meta-exhalatives and metasediments. Gold occurs in the metamorphic host rocks in association with arsenopyrite and arsenic-antimony sulfides which occur in lenses and disseminations within the host rock. Gold grains occurring in the metamorphic host rocks range. in size from sub-micron to a few microns in diameter.

Jan 1, 1987

By D. Lui, B. G. Thomas, B. Ho

"Results from mathematical models and plant experiments are combined to quantify the effect of transverse depressions and oscillation marks on heat transfer in the continuous casting mold. A heat transfer model has been developed to calculate transient heat conduction within the solidifying steel, coupled with the steady-state heat conduction with the continuous casting mold wall. The model features a detailed treatment of the interfacial gap between the shell and mold, including mass and momentum balances on the solid and liquid powder layers. The model predicts the solidified shell thickness down the mold, temperature in the mold and shell, thickness of the resolidified and liquid powder layers, heat flux distribution down the mold, mold water temperature rise, ideal taper of the mold walls, and other related phenomena. The important effect of non-uniform distribution of superheat is incorporated using the results from previous 3-D turbulent fluid flow calculations within the liquid cavity. Results from plant experiments confirm that transverse surface depressions and oscillation marks form at the meniscus and move down the mold. Measurements of mold thermocouple temperatures and breakout shell thickness were used to calibrate the models. The results indicate that the surface depressions and oscillation marks are filled with mold flux, but still have a significant effect on decreasing heat transfer. The predicted mold temperature fluctuations are consistent with measurements. If the depressions become filled with air, their effect is greatly increased. These results should be useful in the difficult task of interpreting transient mold thermocouple signals for on-line quality monitoring.IntroductionMany different types of intermittent surface defects on steel slabs arise during initial solidification in the mold of the. continuous casting machine. These defects include deep oscillation marks, surface depressions, and cracks. They may lead to quality problems, such as slivers, in the final rolled product. In severe cases, breakouts may occur, where liquid steel bursts through a thin section of the shell and drains over the casting machine below the mold."

Jan 1, 1997

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By Xiang Zhu

Xidagou is the largest waste water discharge channel of the Anshan Iron and Steel Complex (AISC) with average flow rate of 8000 cubic meters per hour, which is about 75% of the total effluent of the AISC. The waste water from Xidagou seriously polluted the Taizi River Basin. In order to meet the Chinese Class V Standard for Surface Water Discharge and the Standard for Recycled Industrial Water Reuse, with the aid of the World Bank, the AISC began the treatability studies in 1991. Based on the bench-scale test, the AISC carried out pilot-scale treatability studies on three different treatment processes and five different chemical coagulants for more than half a year in 1992. The study results show that the processes of primary sedimentation- chemical mixing and flocculation-secondary sedimentation-filtration can meet the requirement and that PFS and PAM are effective and economic chemical coagulants.

Jan 1, 1994

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993

By J. Brent Hiskey

Recently basic concepts of semiconductor electrochemistry and solid-state electronic structure theory have been applied to the dissolution of mineral electrodes. In this paper, fundamental aspects of semiconductor electro- chemistry and interfacial charge-transfer processes are reviewed. Information regarding the electronic and semiconductor properties of chalcopyrite is summarized. The electrochemical response of chalcopyrite in acidic solution is analyzed in terms of initial dissolution processes. The initial charge- transfer reaction involves the consumption of holes. It has been shorn that Fermi level pinning is consistent with observed electrochemical and dissolution behavior. Semiconductor electrochemistry has proved helpful in explaining the formation of intermediate surface films produced during the initial stages of chalcopyrite dissolution

Jan 1, 1993

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015

Al2O3,-WC Composite powder for cutting tools was synthesized by self-propagating high-temperature synthesis using A1 powder as a reducing agent. WC, W2C and Al2O3 were concurrently formed in WO3Al-C system. It was found that the complete reaction was achieved with excessive addition of carbon and appropriate processing parameters such as degree of dilution, particle size of aluminum, compaction pressures of green pellets and carbon source. The final product which was leached by 50% HN03+HF diluted solution was consisted of Al2O3-55wt% WC having 2-3um of mean particle size.

Jan 1, 1999

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

By Richard D. Hagni

Process mineralogy has not been given adequate attention in years past, because geologists have not been sufficiently interested in applying mineralogical techniques to industrial processes, and most process engineers are not adequately trained to use them. Although some individuals and institutions have made efforts to improve the situation, it is only in the last few years that the significance of applying the methods of mineralogy to a wide variety of industrial processes has been fully appreciated. Presently, the formation and organization of several groups devoted to applied mineralogy have created a more amenable climate for the development of process mineralogy. As a result, the presentation, discussion, and publication of the results and case histories of process mineralogy have become fairly common. Short courses affording hands-on experience with applied techniques are now available to the many geologists and process engineers engaged in industrial mineralogical processes. The future role of the process mineralogist is viewed as an expanded one, which will increase in value.

Jan 1, 1982

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By Guy Deschênes

In spite of the wide use of lead compounds to enhance cyanidation of free milling sulphide-bearing gold ores, an industrial control method was only implemented four years ago. This study presents the results of the investigation that led to the development of the on-line control technology. Two free milling sulphide-bearing gold ores and high purity minerals were used to develop and test the concept. The first ore contains 2.8 g/t Au, 6.2% pyrrhotite, 2.1% pyrite 0.6 % arsenopyrite, 0.1% chalcopyrite and 0.1% organic carbon. The second ore contains 10.4 g/t Au, 3.2% pyrite, 0.8% pyrrhotite and 0.38% chalcopyrite. The first ore showed a much higher oxidation rate in the pre-leach than the second one and consumed seven times more cyanide. A relation between the formation of thiosulphate and thiocyanate and the additions of lead nitrate were quantified. The ?reducing power?, a titration with permanganate, predominantly determines the concentration of thiosulphate and thiocyanate in cyanide solution. The relation between the reducing power and the addition of lead nitrate at various concentrations of pyrrhotite and chalcopyrite in the ores was established, providing a monitor/control strategy for lead nitrate addition.

Jan 1, 2006

By Godwin J. Igwe

For soil remediation technology to be effective, a thorough understanding of the interactions between a targeted contaminant and the soil matrix is crucial. Proper selection of remediation technology, based on understanding the bonding/binding characteristics of the soil and contaminant, can often result in significant remediation cost savings. Contaminated soil cleanup is complicated by both the physical nature of the soil formation and the behavior of contaminants introduced into the formation. Contaminants can exist in the subsurface in different phase attached to the soil surfaces, dissolved in the ground water, or occupying pore spaces as a separate gaseous or liquid phase. Contaminants properties and how they exist in the subsurface influence their toxicity, mobility and treatability with different remediation technologies A soil characterization study was performed to provide information for remediation technology selection for an inorganic lead contaminated soil. The soil pH, TCLP analysis, thermogravimetric analysis, the soluble anions and cations present, equilibrium leaching tests, analysis by x-ray fluorescence, sequential extractions and speciation analysis using scanning electron microscopy, were all used. Results provided many insights into contaminant behavior in the soil, indicating ultimately whether soil washing or solidification/ stabilization remediation technologies were applicable.

Jan 1, 1994