Search Documents

By Guo Xian Jian

In this paper, an alternative process to recover the value metals from polymetallic gold ore by FeCh leaching was proposed. In the process, gold was recovered by direct cyanidation from the leaching residue, the isolative electrolyte in chloride solution was selected to recover lead, the cementation with copper powder was used to recover silver and the solvent extracting was applied to recover copper and zinc. The total recovery of gold, lead, copper, silver and zinc in the process is 90.8%,96.05%,84.3%,81.98% and 54% to the bullion of gold, lead and silver and sulfate of copper and zinc, respectively. The process conditions selected for FeCh leaching are the temperature of 104°C, leaching time of 6 hours, Fe3+ content of 140 g/l and stoichiometry of FeCl3.

Jan 1, 1996

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By H. Bernier

The Noranda Inc., CCR Division, copper refinery located in Montreal-East, Québec, Canada, has expanded over the years to reach a capacity of 410,000 metric tons of cathode production per year. The expansion process resulted in nine, parallel, 200 m. long bays each equipped with its overhead cranes and manually operated washing machines. Anode scrap washing and piling was done manually. The mechanization of the tank house involved the elimination of 18 cells at one end of each of the bays in order to install transfer conveyors where anode scrap and cathode loads are deposited by the bay cranes. The cathode loads are brought by new transverse cranes to new machines where cathodes are washed, piled in predetermined bundle weights, check weighed, strapped then shipped in trucks or railroad cars. Suspension bars are automatically removed, stacked in magazines and sent back to the starting sheet machines. Anode scrap loads are brought to machines located near the anode furnaces where they are washed and piled in bundles for easy charging. The mechanization has eliminated numerous hazardous jobs and has realized a reduction of 0.2 man-hours/ton. After these modifications, the refinery production capacity now stands at 370,000 metric tons per year.

Jan 1, 1987

By Junji Shibata

Extraction behavior of Ti(IV) and other metal ions, such as Fe(III), Fe(II), Cu(II), Zn(I1) and Co(I1) from acidic solutions like sulphuric acid and hydrochloric acid was studied in order to recover titanium from the waste solution in Ti02 production. Extractant used was tri-alkyl phosphine oxide whose trade name was Cyanex 923. Then, a study was made of the idea of simulating a countercurrent multistage extraction system, using the results of batch extraction. The simulation was camed out on extraction and saipping behavior for a Ti(1V)-H$O,-Cyanex 923 system. From the simulation result., the optimum operating condition of the system was considered.

Jan 1, 1994

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

By A. A. Trickett

In the treatment of gases from pyrometallurgical processes prior to acid manufacture, volatile components, sulphur trioxide and particulates ,are removed in wet gas cleantng systems. In the process a weak acid stream is generated, typically less than 10% H2S04, contaminated with volatiles such as arsenic, fluoride and chloride', plus metallic particulates. This effluent stream has, in the past, been disposed of in a variety of different ways. As a result of changing environmental legislation, smelters are having to review alternative solutions for treating this effluent stream. This paper' will describe a process developed by Chemetics which treats this effluent stream, generating a small dry metal sulphate stream plus a clean acid stream which is suitable for recycling to the smelter acid plant.

Jan 1, 1992

By K. G. F. Janssens

In the process of annealing a deformed metal the microstructure changes due to concurrent recrystallization, grain growth and precipitation. It is common knowledge that all three of these microstructural transformations show a strong dependence on each other, and that an overall model must take the relevant interactions into account. Aiming at the development of an approach which is useful in the more general case, a computational model is being developed which allows the prediction of the three dimensional grain topology and orientation distribution function of any metal submitted to subsequent deformation and annealing, taking into account concurrent recrystallization, grain growth and precipitation and starting from a statistical representation of the deformed microstructure. In this contribution a case study is presented which illustrates the potential and limits of the state of the art in the field. Keywords: Microstructure Evolution Modeling, Irregular Cellular Automata, Deformation, Precipitation, Recrystallization, Grain Growth

Jan 1, 2003

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By Zhiqiang Han, Anil K. Sachdev, Baicheng Liu, Guomin Han, Alan A. Luo

The growth of precipitate phase ,B-Mg11Al12 in Mg-Al alloy is closely related to interface anisotropy and elastic interaction. The aim of this work is to investigate the effects of the interface anisotropy and elastic interaction on the morphology evolution and growth kinetics of the precipitate. In the work, the precipitation of ,B was studied using phase field modeling. In the model, the chemical free energy of the precipitate and the matrix were obtained via thermodynamic calculation. It is demonstrated that the interface anisotropy results in lath-shaped precipitate and the elastic interaction affects the shape of the end of the precipitate. The interface anisotropy causes uneven growth in different directions and the elastic interaction influences its preferential growth orientation. By combining the interface anisotropy and elastic interaction in the phase field modeling, the results showed that the precipitate phase has a lath-shape with lozenge ends, which is in agreement with experimental observations.

Jan 1, 2013

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Grigore Matei

The thermodynamic properties of CU2S-FeS system are important not only in the case of copper smelting but also in the case of general pyro-mctallurgy, However there are not many reported activity data In this study, activities of FeS and CU2S in the CU2S-FeS system were calculated using the Darken's method from the activity data of the CU2S-FeS-Sb2SJ systems measured by the transportation method at 10S0°C. The activities of CU2S and FeS in the CU2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation,

Jan 1, 2003

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By Chang Wei, Zhigan Deng, Jiqiang Liao, Minting Li, Hongsheng Xu, Yan Song, Cunxiong Li, Xingbin Li

"Abstract: Direct ?otation of oxidized zinc-lead ore is characterized by recovery of zinc and lead only around 55% and 50%, respectively. Mineralogical analysis shows that the sample used in the present study is a carbonate hosted zinc-lead ore, with a zinc and lead carbonate content that accounts for 80.14% and 75.63% of the total minerals, respectively. The carbonate hosted zinc-lead ore was hydrothermally sulfidized with elemental sufur and the experimental data indicated that under the conditions employed up to 75% zinc and 82% lead sulfidation extent were achieved. As a result of pre-sulfidation followed by flotation, the recoveries of zinc and lead into flotation concentrate were over 90%. A flotation concentrate was obtained with 52% Zn and 37% Pb from the materials which was treated by sulfidation.IntroductionSulfide ores are the primary source of zinc and lead, and they are becoming depleted; thus, metallurgical investigators are interested in using abundant oxidized zinc-lead ore reserves. The high-grade zinc-lead oxidized ore, which normally has a zinc content higher than 15%, can be disposed of by acid leaching and electrolysis. However, the low-grade ore, which has a zinc content lower than 10%, is difficult to smelt with pyrometallurgy and hydrometallurgy, and the processes are very complicated and expensive in terms of production flow and energy consumption. Therefore, making the low-grade oxidized zinc-lead ore more beneficial has become more important in recent years. Flotation is the most common process, and the primary method of recovering zinc and lead from sulfide or oxide minerals. It is well known that there is a difference between sulfurized and oxidized minerals regarding their separation by flotation. Flotation of zinc and lead oxidized minerals is extremely complex because of the similarities in the physicochemical and surface chemistry of the constituent minerals. There are no known direct-acting collectors capable of producing single metal concentrates [1-3]."

Jan 1, 2012

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002

By Noritaka Horii, Katsuyoshi Kakinuma, Hiroshi Yamamura

"ZrO2 and Y2O 3-doped ZrO2 gel film were obtained by spin coating of sol from Zr-n-propoxide, n-propanol, acetylacetone, nitric acid, and water on a silica glass as a substrate. ·Dried gel films crystallized to monoclinic, tetragonal, cubic and their mixed phases, depending on the chemical composition of sol, .firing temperature, and coating cycles. ZrO2 films with highly preferential orientation were successfully obtained from a solution containing a large amount of n-propanol. The highly oriented ZrO2 film was found to have high transparency compared with non-oriented 'films. Electrical conductivity of 8 mol% Y2O 3 doped ZrO2 film was also measured.Introduction3 mol% Y2O 3 doped ZrO2, which has a tetragonal symmetry is ·well known to have a strong mechanical property and a high toughness. (1) On the other hand, 8 mol % Y 2O 3-doped ZrO2 is high oxide-ion conducting material and is applied to oxygen sensor, oxygen pump, and solid oxide fuel cell (SOFC). (2) Sol-gel methods using metallic alkoxide are widely applied for synthesizing ceramics such as high-purity fine particles, thin film, and fiber. (3) For ceramics films, many reports have been made on SiO2, (4) TiO2, (5) and PZT. (6) Several case studies have been done on zirconia film based on the sol-gel method, (7) - (11) but very few on preferentially oriented film and on systematic Y zO3 doping. Almost zirconia ceramic· films reported were prepared by means of dip-coating. Kamiya et al. (12) and Ganguli et al (13) converted zirconia into fiber. Sol from Zr alkoxide is usually very unstable, and a stabilizing agent such as glycol or ß-keton is used beforehand (7) (14)."

Jan 1, 2000