Search Documents

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By María Guadalupe Sánchez-Loredo

Silver from nitrate aqueous solutions was extracted by commercial organophosphorous extractants (tri-n-butylphosphate, Cyanex 471x, Cyanex 301 and Cyanex 302). Quantitative silver extraction was obtained using the Cyanex reagents. After loading, aqueous solutions of several reducing reagents were used to prepare fine silver powders by reductive stripping. Only both extractants Cyanex 471x and tri-n-butylphosphate (TBP) could be reductive stripped and regenerated by aqueous solutions of ascorbic acid, and Cyanex 471x was decomposed to the corresponding phosphine oxide by using sodium borohydride as reducing agent. Silver was recovered as fine particles, which were characterised by means of scanning electron microscopy (SEM). Micrographs showed that the powder size and morphology were directly affected by the composition of the applied organic phases and aqueous reducing media.

Jan 1, 2003

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By Ahmad Umar

A variety of ZnO nanostructures such as sea-urchin-like structures composed of nanowires and nanorods, nanocombs, nano/micro spheres and cages, star-shaped ZnO nanostructures, flower-shaped nanostructures, needle-like nanostructures etc. have been synthesized applying two different fabrication techniques i.e. thermal evaporation and cyclic feeding chemical vapor deposition techniques at different reaction parameters such as reaction temperature, growth period, reactant concentrations, types of source material and substrates etc. It was observed from the experiments that the morphologies of the grown structures were highly influenced by the reaction parameters and fabrication techniques and specific morphology can be obtained at particular reaction parameters in a specific synthetic procedure. Extensive morphological investigations of the obtained products demonstrate that the grown structures are single crystalline and having a wurtzite hexagonal phase. Room-temperature photoluminescence spectra of all the deposited products exhibited good optical properties. Finally, the growth process of the fabricated structures were proposed and discussed in detail.

Jan 1, 2006

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

By Kongfang Feng, Fei Ruan, Zhiyu Liu, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jixu Wang, Jinyin Xie

"Mixing phenomena in smelting reduction furnaces with asymmetric side blowing were studied in this paper. Mixing phenomena in a smelting reduction furnace was represented as the mixing time by electrical conductivity measurements. Experiments were performed in a water model under various operating conditions to determine the effects of horizontal angle, radial angle, inserting depth, flow rate of the upper and the lower side nozzle, the included angle between the upper side nozzle, and the lower side nozzle on mixing phenomena in smelting reduction furnace. Comparing mixing time and mixing phenomena, the optimal conditions were obtained for an asymmetric side blowing process.IntroductionIn recent years, many countries have put forward development strategies for saving resources and environment-friendly, the development of various industries had to face its influence for resources and the environment .As we all know, the steel industry is a pillar industry of the global economy, in which ironmaking is an important part of it. In the modern ironmaking process, the blast furnace is regarded as the most important equipment and tool. But with the increasing scarcity of metallurgical coke resources and considering the environmental impact of such processes, metallurgists proposed the concept of smelting reduction. Smelting reduction processes to produce hot metal from iron ore and coal were being developed as a possible alternative to the traditional blast furnace. At present, a number of smelting reduction processes had been developed all over the world, they were mainly included COREX, HISMELT, FINEX, DIOS, etc."

Jan 1, 2012

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By N. E. Ablesimov

Electron probe X-ray microanalyser of a coating deposited with "Elitron¬22A" electrospark alloying (ESA) set (anode - Cr, base-catode - chrome vanadium steel) has shown that the zone of phase forming can be divided into three parts: the coating itself, diffusion zone and a thermal affection zone in the base material. Waves of iron and chrome concentrations have been found in the diffusion zone. The authors interprete them as a phenomenon of substance self-organizing in the 30 pill deep diffusion zone, characterized by a change of compositions during the transfer of material from the coating to the base: coating - 20 µm (FeCr2), diffusion zone - 30 µm (Fe3Cr, FeCr, Fe4Cr, Fe2Cr), base - steel (Fe - 87 %, Cr - 12 %, V - I %). This ESA phenomen has been noted for the first time. It may be relative to the phenomenon of periodic formation of secondary products during the mutual diffusion of reacting substances in the case of a one-way reaction. Similar regular structures may appear in the diffusion zone during ESA of vanadium steels with vanadium, manganese steels with manganese and so on.

Jan 1, 1999

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By Susumu Okabe

Top blowing lances are employed by the Mitsubishi Continuous Copper Converter for the continuous supply Of reaction gases into moken bath. In order to minimize the refractory wear caused by the interaction between the furnace lining and the melt splash. optimum furnace design and blowing condition are? required. An empirical equation obtained by the physical model study enables the estimation of the splashing rate on a vel1ical plane at a certain distance from the lance.

Jan 1, 1996

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70&apos; s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By S. V. Ketov, V. P. Menushenkov, V. S. Shubakov

"The glass samples were obtained by melting of the oxides mixture SrO-Fe2O3-B2O3(Al2O3) at 1200-1250°C with subsequent quenching of the melt on quickly rotating steel roller. Submicronsized Sr(Fe,Al)12O19 particles were formed in glass-ceramic matrix during the crystallization aging of glass. The aging temperature Tag varied in the range 650-950°C. The submicron-sized hexaferrite powder was obtained by removing of the matrix phases using etching. The samples were characterized by X-ray diffraction, scamiing electron microscopy and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10 kOe. The samples of magnets were obtained by pressing of the hexaferrite powder at RT and subsequent aging in the range 900-1200°C. The aged samples exhibit coercivity value up to 8 kOe.IntroductionStrontium M-type hexaferrites have been widely used in technology and industry mainly for production of permanent magnets owing to their appropriate magnetic properties, chemical stability and low cost [1,2]. The SrFe12019-based compounds are characterized by high magnetocrystalline anisotropy and single easy magnetization axis. The highest coercivity is received for monodomain, defect-free single crystal particles with size D - 100 mn. Finely grained strontium hexaferrite prepared by chemical methods such as sol-gel pyrolysis and oxide glass crystallization exhibits high coercivity up to 6-8 kOe [3-5]. Owing to the partial substitution of Al for Fe in the strontium hexaferrite leading to the increase in the magnetic anisotropy field Ha=2Ki/M,, the increase in the coercivity may be received [6]. The notable results were achieved using the SrO-Fe2O3-AlzO3-B2O3 glass crystallization and formation of perfect submicron crystals of alumina-doped hexaferrite [ 6, 7]. The coercive force of glassceramics reached values of up to 10 kOe. Hexaferrite particles are well faceted and have the shape ofhexagonal bipyramids with truncated vertexes [7].In the present paper, we report results of our investigation into the SrO-Fe2O3-B2O3(Al2O3) glass crystallization, hexaferrite powders and permanent magnets, which were prepared by pressing submicron-sized hexaferrite powders at RT and subsequent sintering at 900-1200°C."

Jan 1, 2012

By Mingchun Lu, Zhijia Liu, Xueqi Zhang, Jianliang Zhang

"In order to solve the problem of shortage of scrap, especially high quality scrap, a new substitute for scrap or DRI has been developed. The decarbonization mechanism of granular pig iron has been analyzed and the technical process and decarbonized granular pig iron have been evaluated in this paper. The research result shows that this new process is superior to direct reduction process in product quality, construction investment, operation flexibility, production efficiency etc. Decarbonized granular pig iron (DGPI) not only can be used as conventional scrap but also can be charged into EAF as high purity .burden equivalent to heavy scrap:IntroductionIn the past years, with the universal application of continuos casting technique in China, the amount of scrap generated inside steelworks has been reducing continually. On the other hand, the EAF steel proportion is increasing and this gives to the obvious change in structure of steel product. At present, the requirement on both scrap quantity and scrap quality is being paid more and more attention. Because China is a country which is devoid of scrap and poor in resource (nature gas and high grade iron ore) for developing direct reduction iron (DRI) so that sponge iron can not be produced cosmically in China and has to be mainly imported. Instead of part of scrap, some cold pig iron in cold state has been charged into EAF in China. However the high carbon content in pig iron has limited its proportion in EAF metal burden. Because the price of pig iron is lower than that of imported DRI in China, the technique of granular pig iron decarboniztion is hopeful to become effective way to produce substitute for scrap or DRI."

Jan 1, 2000

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By Fathi Habashi

The behavior of pyrite, covellite, and arsenopyrite during leaching is different from other sulfides due to the presence of the disulfide ion, Sl. Arsenopyrite contains in addition, the diarsenide ion, Asl. The disulfide ion undergoes auto-oxidation in high acidity leading to elemental sulfur and sulfide ion formation: The sulfide ion may oxidize further by oxygen to elemental sulfur if high acidity is maintained. In neutral medium, the disulfide ion does not undergo auto-oxidation but oxidizes to thiosulfate then to sulfate: This leads to the two overall reactions observed experimentally: In acid medium and in neutral medium Covellite and arsenopyrite behave similarly.

Jan 1, 1995