Search Documents

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Albaharna O. T., Argyropoulos S. A.

"This paper describes the development and the implementation of process control in a variety of instruments used in metallurgical laboratories. These instruments are used for different research projects in extractive metallurgy. Hardware and software aspects for this implementation are described and analyzed. Extractive metallurgy applications where process control was .used are presented. IntroductionMicroprocessors are invading almost every area of our lives and are turning up in unexpected applications. A great deal of new equipment which is coming into the market have built- in microprocessor systems. Nevertheless, the area of upgrading existing processes has been slow to develop. There are a variety of reasons for this, and many of these are economic. One of the principal reasons, however, is the general reluctance on the part of many organizations to commit a strong effort to put this new technology into their existing processes.Microprocessor systems developed ""in lab"" are capable of not only measuring thermophysical events which are taking place in metallurgical furnaces, but simultaneously controlling these furnaces. In this paper software and hardware aspects in the implementation of microprocessor control for resistance and for induction furnaces are presented. In addition to this, metallurgical results are given from experiments where this furnace control was applied."

Jan 1, 1989

By R. Reed von Gal

The majority of zinc strip produced in the world today is cast on the Hazelett twiri-belt continuous casting machine. Ten of these machines are currently operating worldwide, and one machine is under construction for the People's Republic of China. The caster, which was first patented in 1947, was originally developed for aluminum and copper alloy casting. In the early 1960s, the design was expanded into zinc casting and within ten years the industry had essentially converted from casting and rolling ingots to twin-belt continuous casting with in-line rolling. The casting process employs two parallel, moving. water-cooled belts as the major mold surfaces. Together with two strings of side dam blocks, the design offers a four-sided moving mold which produces a continuous strip or bar. This paper will cover a bit of, the history, as well as the current technology surrounding this high production process for zinc strip production.

Jan 1, 1990

By Ulises Crossa Archiopoli

We describe a technique that allows rapid imaging of the thermal diffusivity of the sample by a modified photo-thermal technique. The thermal diffusivity in hardened steels strongly correlates to the hardness. Hence in a noncontact manner and with optical microscope resolution, a 2D map exhibiting the crystallographic phases and hardness of the sample can be retrieved. Two almost collinear laser beams scan the surface, one as a modulated pump and a second as a CW probe. The deflection of the probe carries information on the thermal expansion of the sample and with it, on the thermal diffusivity. It is shown that a single determination of the time delay of the modulation of the probe beam can be used to retrieve the thermal diffusivity.

Jan 1, 2010

By Pengfu Tan

Xstrata Copper at Mount Isa in Australia has operated one copper Isasmelt furnace and four P-S converters. The phenomena of foaming occur in above 10% of converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow. The model predicts the chemistry and viscosity of copper skims during copper blow. The effects of oxygen potential, charge of dirty materials, slag carry-over, under-blowing, over-blowing, and temperature on the foaming and viscosity of copper skims have been discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2006

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By A. E. M. Warner

At the Copper Cliff Smelter, Inco Limited has extensive experience in converting primary smelting mattes over a broad range of nickel/copper ratios and compositions. In the past 35 years, technology developments at Inco have reduced the number of Peirce-Smith converters in Nickel/ Bulk (nickel-copper matte) service from 13 to the current 5. This paper will discuss: ? The performance and life of ?stretch? 13.7m shells versus conventional 10.7m converters. ? Process control and information system development from the early 1980?s to view converter aisle status on a continuous basis to the recent central control of the stretch shells. ? Nitrogen cooling of finishing matte from plant testing to implementation in the early 1990?s to replace the dedicated cooling converters. ? The impact on converting of changing the smelter flowsheet in the early 1990?s. ? A current program to develop a converting strategy for the future to address environmental issues and profitability.

Jan 1, 2005

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By Aline Maria dos Santos Teixeira

Serpentinite is an ultra basic and metamorphic rock consisting mainly of magnesium, calcium and silicon oxides. The rock under study is a host rock of chromite mine located in Andorinha, BA. The objective of this paper is to evaluate the rock's physical and chemical characteristics to be used as an additional fertilizer of acid soils. After comminution, rock samples were submitted to chemical analysis, XRD, SEM-EDS and TGA. Afterwards, particle size distribution was determined. Result analysis confirms that our rock consists mainly of dolomite, calcite and diopside. According to the result obtained, it can be said that the serpentinite rock has promising applications in agriculture for the correction and additional fertilization of acid soils. However, it is necessary to study the characteristics of the rock such as its dangers and toxicity as well as evaluate them according to the legislation for corrective acidity.

Jan 1, 2010

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By José R. Parga

In some parts of the Comarca Lagunera with population of about 2.5 million people, situated in the central part of northern México, chronic arsenic poisoning is endemic and severe adverse effects attributed to As exposure have been reported. Lifetime exposure to arsenic will develop classical symptoms of arsenic poisoning such as skin pigmentation changes, gastrointestinal disturbances and neurological changes. There are several methods available for removal of arsenic from well water in large conventional treatment plants, however a very promising electrochemical treatment technique that does not require the addition of chemicals or regeneration is Electrocoagulation (EC). The EC operating conditions are highly dependent on the chemistry of the aqueous medium, especially conductivity and pH. In this study, Powder X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Mössbauer Spectroscopy (TMS) were used to characterize the solid products formed at iron electrodes during the EC process. This study will provide an introduction to the fundamental concepts of the EC method. Finally the results of this study suggest that the presence of maghemite and magnetite particles can be used to remove arsenic (III) and arsenic (V). In the field pilot plant scale study more than 99% removal of As species from groundwater is achieved.

Jan 1, 2005