Search Documents

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992

By Joni M. Barnes

A strain of Pseudomonas stutzeri isohted from selenium contaminated surface waters, was found to be effective . in reducing selenate (Se04 2) stoichiometrically to selenite (Se03 2 '), which was further reduced to elementaJ selenium (Se0 ). These reactions were concurrent with the microbial oxidation of lactate. In order to assess quantitatively the amounts of seilenate and selenitein solution, improvements to existing analytical methods (ion exchange chromatography and inductively coupled plasma atomic emission spectrophotometry technique) .were made.

Jan 1, 1991

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the 'half-life and the amount of work done, the 'half-life-tonne' are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983

By Wilhelm Brandstätter, Johannes Steiner, Alois Triessnig, Christian Redl

"The results of numerical simulations of bubble detachment from an orifice in a horizontal plate submerged in liquid are presented. The bubbles are created by forcing gas through this orifice into stagnant liquid. The simulations are performed with a two-dimensional incompressible Lattice Boltzmann (LB) scheme. In previous works the same problem was investigated by two-phase simulations in which surface tension effects were considered by an interaction potential formulation between the phases. In contrast, in the present work a volume of fluid (VOF) model consisting of a carrier fluid and a passively advected scalar function for the calculation of gravitational and surface tension forces, respectively, is used. The aims of this study are to examine the applicability of the one-phase LB method to the numerical analysis of bubble formation and to verify the theoretical and experimental predictions of the dependencies of the departure diameter on gravitational forces, surface forces and wettability effects. To this purpose the simulations were performed at different values of gravitational acceleration g, surface tension coefficient s and contact angle ß. Nonlinear fits to the data yield functional dependencies which are in good agreement with the predictions. IntroductionBubble formation behavior is an extensively studied subject, especially in chemical engineering, power industries and metallurgical processing. Knowledge of the underlying physics of bubble motion is, for example, required for the design of chemical reaction towers and agitation tanks. Another important application is the argon gas injection through the wall of the tundish nozzle into liquid steel stream to deter clogging with solid inclusions. Argon bubble motion and its effect on flow depends greatly on different parameters, e.g. gas flow rate and size of the bubbles. Thus, if these bubbles are not managed properly, they can become encapsulated upon solidification and result in undesirable impurities in the material [1, 2]."

Jan 1, 2004

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By Wayne C. Stewart

Freezing of high pressure air lines and pneumatic equipment has been a recurring problem in the Thompson Smelter. The particular severity during the winter of 1989-90 resulted in costly process disruptions and repairs. A process improvement team with representatives from operations, engineering and both maintenance supervision and the shop floor was established to develop solutions. Their mandate included process evaluation, design, equipment and in-plant commissioning. In 1990, upon recommendation of the team, we installed three Refrigerant/Desiccant air dryers with a total capacity of 20,000 S.C.F.M. to service the Smelter. This paper discusses processes and process improvements associated with this installation.

Jan 1, 1993

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues' by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions' selectivity.

Jan 1, 1993

By C. Pereira

Spent nuclear fuel (SNF) can be treated in a molten salt electro refiner for conversion into metal and mineral waste fonns for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed.

Jan 1, 1996

By N. Kanari

Reactivity of MgO towards C12+air, C12+N2 and C12+CO gas mixtures was studied up to 1000 °C. Carbochlorination of MgO occurs at temperatures lower than that of its oxychlorination. Effects of gas flow rate, temperature and partial pressure of the carbochlorinating gas mixture on the reaction rate were investigated. The apparent activation energy of MgO carbochlorination is 49 kJ1 mol between 425°C and 600°C. At 550 °C, the apparent reaction orders with respect to C12+CO, C12 and CO, are 2.37, 1.47 and 0.89, respectively. At this temperature, the maximum reaction rate was obtained using a C12+CO gas mixture having a Cl2lCO molar ratio equal to about 0.6.

Jan 1, 1998

By Alan P. Prosser

The heap leaching of gold ores by cyanide solution was simulated by computer program. The program uses only basic m1neralogical and chemical data; no process testwork data, such as column leach results, are required. The simulation can be used to forecast the consequences of various changes before and during the testwork, design and operation stages of a particular ore-process system. Also, data about the state of different parts of the heap at various times help create an understanding of what is happening. The effects of mineralogical and process variables on the overall performance of the ?heap leaching process are illustrated. Comparisons are made to column leach tests and production data. The potential of the simulation strategy is discussed for making better use of operating experience and for suggesting specific research objectives. It has become clear that more attention should be paid to other metals that dissolve in the solution.

Jan 1, 1989

By Jerold L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the ,soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1993

By Metehan Erdogan, Orhan Gökçe Göksu, Ishak Karakaya

"An experiment (mixture) design was created to optimize the process parameters of the electrochemical reduction of CaW04 to W in molten CaCl2-NaCl eutectic mixture. Temperature, applied voltage and the length of Kanthal wire winding of the CaW04 pellets were selected as the process parameters that were allowed to vary between the predetermined minimum and maximum values. The rates of the electrochemical reductions were interpreted from the variations of current and total charge vs. time graphs under different conditions. The analysis pointed out that 640°C and 2.81 V resulted in the fastest reduction. Itwas seen that the effect of Kanthal wire winding on the output current was less pronounced when compared to the other two parameters.IntroductionFFC Cambridge Process [1] has been applied to a number of metal oxides in laboratory experiments to produce metals. In nearly all of these studies, the electrolysis temperature was around 900°C, the electrolyte was pure CaCl2 or CaCl2 containing salt solutions and the anode was graphite. However, it was recently shown that the electrochemical reduction process of metal oxides in CaCl2 containing electrolytes at the mentioned high temperatures was not suitable for tungsten production [2], It was reported that as soon as WO3 contacts CaCl2, the following reaction occurs:"

Jan 1, 2012

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By Stig Petersson

Slag from the converting of copper matte is usually recirculated to the smelting furnace. This recirculation generally causes disadvantages as magnetite-build-up in the furnace, accumalation of impurities as antimony, lead, nickel etc in the process. The treatment of converter slag in a separate furnace in order to recover the copper and nickel content would be of advantage from several points of view. At the Mining and Metals Division, Boliden, testwork has been carried out to treat converter slag from the PS-converters in a separate furnace. The tests have been performed in laboratory and pilot plant scale. The pilot plant tests have been carried out in a TBRC with charges of 5 tons. Based on these tests a full scale TBRC has been projected in order to treat the slag from the PS-converters. This slag will be reduced with copper concentrates to give a matte and a final slag low in copper and nickel. The background and data from the testwork are presented. Also the lay out, technical data and flowsheets for the projected process are shown as well as some production data from the Rönnskär smelter.

Jan 1, 1976

By M. Friák, L. G. Wang, M. Šob, V. Vitek

"The paper gives an account of applications of quantum-mechanical (first-principles) electronic structure calculations to the problem of theoretical tensile strength in metals and intermetallics. First, we briefly describe the way of simulating the tensile test and the electronic structure calculational method. Our approach is then illustrated on calculations of theoretical tensile strength in W, NiAl and transition metal disilicides MoSi2 and WSi2 with C11b structure. In Wand NiAl, we consider uniaxial tension along [001] and [111] directions. Although tungsten is elastically nearly isotropic (C44 = C”), theoretical tensile strength exhibits a marked anisotropy (oth/001 = 29 GPa, o'th/111 = 40 GPa). Calculated results compare favorably with experimental value of 24.7±3.6 GPa obtained for tungsten whiskers grown along the [110] direction. Similarly, in NiAl, the 'hard' orientation [001] differs very significantly from the [ill] orientation (oth/001 = 46 GPa, oth/111 = 25 GPa). This anisotropy is explained in terms of higher-symmetry structures present or absent on the calculated deformation paths. In disilicides, the theoretical strength is calculated for [001] loading (oth/001 = 37 GPa and 38 GPa for MoSi2 and WSi2 , respectively). The role of relaxation of internal structure parameter is discussed and changes in bonding conditions during the tensile test are analyzed.IntroductionIn most engineering applications, the strength of materials is limited by the presence of internal defects. If there were no defects, then, for example, the tensile strength could be several orders of magnitude higher and its value would be comparable with that of shear modulus. Therefore, the strength of ideal (defect-free) crystal represents an upper limit of attainable stresses, which is called the ideal strength. While it may not be possible to achieve the ideal strength in practice, it is not possible to exceed it. However, the ideal strength is already approached in situations which are technologically relevant. These include the low-temperature deformation of inherently strong materials, such as diamond, Si, Ge and some of the transition-metal carbonitrides, deformation of whiskers, nanoindentation of materials with low defect densities, hardened thin films and coatings etc. The ideal strength sets the limits of elastic stability of a solid. Its knowledge is useful for estimation of the ideal work of fracture stresses needed for homogeneous nucleation of dislocations and for modelling of crack propagation."

Jan 1, 2001

By Singareddy R. Reddy, Ramana G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. An expression for the activity coefficient of a dilute solute, 2(oxygen), in a binary solvent 1-3 is derived. It is used to calculate the logarithmic activity coefficient of oxygen in Pb-O-Gu, Pb-O-Bi, AgO- Sn, Pb-O-Sn and Ag-O-Pb metallic systems. Self interaction parameter of the solute is derived from the partial Gibbs energy of solute using constant compositional path. The derived equation is used successfully to deduce the self interaction parameter of oxygen in Pb-O-Gu and Pb-O-Bi metallic systems. The predicted thermodynamic parameter data i.e activity coefficient and self-interaction parameters are in an excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionThe nature of solute interactions such as oxygen, nitrogen and sulfur with the metallic solutions are important for a number of chemical and metallurgical processes. Several theories [1-23] have been developed to evaluate fundamental thermodynamic properties of solutes constituting two elements. The activity of solutes has been calculated using statisticalor quasi- chemical approach.Wagner's [4] Ideal Solvent Model is based on one energy parameter to describe the compositional dependencies of the activity coefficient of nonmetallic solutes such as oxygen in binary metallic solutions. This model depends on a constant energy of interaction for the exchange of atoms from the coordination shell of an oxygen atom to the shell of an interstitial site and cannot account for properties of strongly interacting systems [4]. Therefore, several attempts have been made to improve the Wagner's model for the strongly interacting systems. [10-16]."

Jan 1, 1996

By Carla Lupi

NiMH sealed cells (portable cells) are today widely used in all consumer applications replacing primary alkaline batteries: wireless mobile communication, portable computers and camcorders, are the largest application segments. The Italian market. of NiMH cells is steadily growing, following the impressive penetration rate of the cellular phones. The organization of a national collecting system and correct recycling process are the key factors to prevent environmental impact associated to these wastes, while the metal values recovery can improve the feasibility of the recycling process The University of Rome, Texeco Engineering S.d, and MO.SMO.DE. S.a.s. have developed a combination of mechanical and hydrometallurgical processing to recover Nickel, and Cobalt salable products and rare earths intermediate products. A new plant located in South Italy, designed after this technology, is able to recycle waste Ni-MH batteries collected in the Italian territory, together with other industrial and portable batteries based on different chemistries. The process is able to treat both individual cells and plastic power packs and includes as basic steps an original crushing and elutriation treatment to separate plastic, metallics, and active mass components that are subsequently treated by a hydrometallurgical process to recover Ni, Co, and RE. The hydro metallurgical main steps are: acidic leaching, RE separation, multistage precipitation of Ni, Co and Fe and final solvent extraction on dissolved Ni and Co salts. For each operation the operative condition have been determined.

Jan 1, 2000

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011