Search Documents

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Matthew Jeffrey

Due to the increasing environmental and public concerns over cyanidation, there has been a large amount of research into viable alternative lixiviants. Despite these studies, there is little published data directly comparing the kinetics of gold leaching for each of these alternatives: most of the literature is concerned with gold extraction from ores. This paper presents a detailed kinetic study of gold leaching in cyanide, armmonia/thiosulfate and chloride/hypochlorite solutions. The gold leach rates were measured using a rotating electrochemical quartz crystal microbalance (REQCM). This instrument allows the mass of a gold sample to measured in?situ, with a sensitivity of less than 10 ng. From the results of these studies, it is possible to select experimental conditions where the leach rates of the alternative lixiviants are similar to that for the traditional cyanide system.

Jan 1, 1998

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Evan O. Jones

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions.

Jan 1, 1995

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By S. Viswanathan, Q. Han, A. S. Sabau

"In spite of recent advances in the mathematical modeling of fluid dynamics for materials processing applications, no significant advances have been made in the numerical discretization of these equations. In this work, the application of two-step projection methods for the numerical simulation of interdendritic flows is discussed. Unlike previous methods, the methods presented here are constructed for the exact equations which are characterized by variable density and volumetric fraction of the liquid. The drag terms, which describe the momentum loss due to the flow around and through the dendrite structures, are treated implicitly. Numerical examples for shrinkage-induced flow during solidification of an Al-4.5% Cu alloy bar is used to illustrate the effectiveness of the proposed algorithm.IntroductionLiquid contraction during solidification plays an important role in the formation of casting defects such as shrinkage voids, microporosity, and macrosegregation. Owing to their importance, the study of transport processes during solidification have received considerable attention during the past years [1, 2]. By the use of volume-averaging techniques, the mass and momentum equations for flow through a stationary dendritic structure were derived [3]. By using the volume-averaging techniques for multi-phase systems, two-phase transport equations for solidification problems were derived [4]."

Jan 1, 1999

By V. V. Satya Prasad, A. Sambasiva Rao

Electroslag melting technologies have recently been developed for recycling light scrap of valuable metals and alloys such as superalloys and oxygen free high conductivity (OFHC) copper at Defence Metallurgical Research Laboratory (DMRL), Hyderabad. Conventionally, electroslag melting processes use consumable electrodes. Because of the difficulty in compaction of scrap into a consumable electrode of satisfactory quality, non-consumable electrodes such as graphite and water-cooled copper have been designed. Electroslag remelting using a water-cooled non-consumable electrode was developed to melt scrap of a nickel base superalloy. Sound ingots with smooth surface finish and properties comparable to vacuum melted superalloys could. be obtained from scrap using this process. A modified electroslag crucible melting process using graphite crucible and graphite electrode was developed for recycling OFHC copper scrap. Copper ingots with less than 10 ppm oxygen and electrical conductivity"" 100% IACS could be produced. The same process was also utilized to produce copper-based alloys such as copper-chromium and copper-titanium starting from copper scrap.

Jan 1, 2000

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By Qiang Zhong, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Viscosity of slag determines the production efficiency, energy consumption and distribution of elements between metal and slag, which is very important for pyrometallurgy. Slag of goldantimony ore blast furnace smelting has seldom been studied. In this paper, the viscosities of gold-antimony ore smelting slags of different composition have been studied by the rotating cylinder method. The results showed that, for a slag of 38.95% SiO2, 16.17% CaO, 25.97% FeO, 10.25% Al2O3, 5.17% MgO, the viscosity can be decreased by reducing 3.24%-8.5% SiO2 or increasing 3.31%-9.56% CaO content. Complex SixOy z- from SiO2 acts as the main cause for the high viscosity in a slag of high SiO2. The increasing of CaO causes the decreasing of the amount of SixOy z- and the O2- dissociated from CaO breaks the complex SixOy z-, which can decrease the viscosity. Viscosity of different composition slag in the appropriate range temperature can be calculated from the Arrhenius equation.

Jan 1, 2015

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By André Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Mines Camchib Inc.. It is characterized by very fine first generation gold and very coarse second generation electrurn. Successful milling required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented. As a result of the circuit modifications, gold recovery increased from 65 to 81% in flotation and cyanidation. Overall gold recovery increased from 77% to 88-89%. These improvements are mostly attibutable to the recovery of -10 urn gold, whose presence in the Joe Mann ore and original circuit tails had been identified by process mineralogy.

Jan 1, 1989

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By H. H. Kellogg

The Process Fuel Equivalent (PFE) for nine different flowsheets for production of anode copper from sulfide concentrates has been evaluated and compared for a set of uniform conditions and a "standard" concentrate analysis. The processes considered are: reverberatory smelting, (wet-charge and hot-calcine charge), electric furnace smelting, Outokumpu flash smelting (2 versions), mom flash smelting, Noranda Continuous Process (2 versions), and the Mitsubishi Continuous Process. The energy required for the numerous processes auxiliary to the principal smelting processes-¬roasting, drying, air compression, gas handling, dust collection, slag cleaning, acid manufacture, etc.--are separately evaluated and incor¬porated into the process comparisons. The factors in process design that lead to important energy savings are: use of fuel rather than electric energy; use of oil or coal rather than natural gas; maximum use of oxygen enrichment of the process air; drying of charge before smelting, or, even better, drying and preheating of charge by partial roasting in a fluid-bed; recovery of waste heat from all major hot process gases.

Jan 1, 1976

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By Kenneth L. Nash

The control of solubility of waste actinide ions, by conversion to highly insoluble mineral phases has been demonstrated in the laboratory. Actinide metal ions are removed from neutral pH solutions by a combined ion exchange-decomposition-mineralization process based on the application of the naturally-occurring hydrolytically unstable.polyphosphate organic compound phytic acid.

Jan 1, 1999

By M. S. Moats

Galvanic stripping, in conjunction with solvent extraction, has been proposed as a technical option to the challenging problem of iron removal in certain hydrometallurgical processes. The galvanic stripping process is based on the ability of a solid metal to directly reduce ferric ion to the ferrous state in an organic media. Stripping the iron into the aqueous phase is then easily accomplished. Previous work has shown the reaction kinetics and efficiency are affected by such operating parameters as water and oxygen contents, temperature, time and metal reductant. In this study, the optimum operating range for some of these variables was determined. Both zinc and iron metal were used in the separate stripping of iron from D2EHP A. Reasons for the differences in the extent of the reaction obtained using the various conditions are discussed.

Jan 1, 1996

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012