Search Documents

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By Robert Pack

INTRODUCTION SOONER or later in the development of any natural resource it becomes highly desirable to know the quantity of this resource in the country as a whole, as well as of the part that is being developed, for the general course and. conduct of the development work must be governed to some extent by the total supply available. An accurate estimate of the quantity of any natural resource is difficult to make; yet if one is diligent enough one can obtain a pretty accurate idea of the quantity of marketable timber, the acreage of tillable land, or the horsepower that may be developed from the streams, for these are things that may be measured. But any attempt to estimate the quantity of some mineral in the ground appears to enter the realm of imagination and it seems that the estimate can be nothing more than a blind guess. It may appear to be especially futile to attempt to determine the quantity of oil and gas that is available in the ground, for these minerals are so vagrant that even if the quantity now available should be known quite exactly, the quantity that will eventually be obtained may be much less, for certain losses in the extraction of both oil and gas are unavoidable, and just what these losses will be cannot be predicted. Though necessarily inaccurate, estimates of such mineral reserves are, however, of distinct value, for they summarize the existing knowledge of the deposits of the mineral and thus enable those who are interested in some industry that depends in one way or another on this mineral to formulate a rational commercial policy. Some time ago, when the price of gasoline suddenly rose in a rather spectacular manner, the writer was one of the U. S. Geological Survey geologists called upon to help to estimate the quantity of oil that could be obtained in the United States, for the fear had become widespread that perhaps the rate of increase in the price of gasoline was a measure of the rate of depletion of the supply of petroleum. It thus became his

Jan 8, 1917

By William F. Hahn

The Bureau of Mines recognized the problems encountered in low seam mining illumination systems. It was determined that the best way of implementing an illumination system is to integrate the design during the design and fabrication of new machinery at the factory. The purpose of this program was to integrate an approved lighting system in a low seam battery powered scoop and evaluate its performance. This report documents the work performed on this program and the results obtained.

Jan 1, 1980

By R. M. Santmyers

Of the sand and miscellaneous silica produced in the United States , ordinary sand and gravel are , of course , the most important, at least as regards volume of output . The building- construction industry absorbs approximately 75 per cent of the total value of all quartz and silica , as shown in Table 2 of Quartz and Silica, Part I, under "General summary . " Because of their unusual physical properties tripoli and diatomite find extremely wide uses in industry, and as the commercial deposits of these ninerals , especially tripoli , are scattered, large quantities enter into interstate commerce . Whereas ordinary sand and gravel are bulky commodities , these specialties have a fairly high unit value and hence can be transported relatively long distances .

Aug 1, 1931

By P. A. Kennedy

An environmental assessment or impact statement for onshore waste disposal under the Notional Environmental Policy Act is expected to occur with the development of commercial deep seabed mining. An environmental assessment was conducted in order that testing and refinement of nodule waste disposal techniques can he completed prior to 1988, when commercial seabed mining can begin under U.S. legislation. Within this study three classes of process and four classes of waste disposal technique were identified, and five sites were selected as representative of first-generation nodule operations. Each realistic site/process/disposal technique combination was compared against potential effects to determine important characteristics of the rejects and the sites. Regulatory requirements were also considered at each site to identify important issues and their effect on the permitting process. Principal conclusions in the report are the following: (1) uncertainties exist in the regulatory regimes for hydrometallurgical process tailings, primarily regarding classification as hazardous waste; (2) slogs from nodule processing are expected to be inert and relatively easy to dispose of at all sites; and (3) additional physical and chemical information on properties of rejects from all processes is necessary to predict environmental effects.

Jan 1, 1982

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health are investigating technologies that could be used to detect objects, small vehicles, and pedestrian workers that may be in the blind areas of haulage equipment used in mining and construction. A detection system that warns the equipment operator that there is an obstacle nearby could prevent collisions and save many lives each year. One popular technology for collision warning systems is radar. Several different types of radar have been tested in the laboratory and on mining equipment. Early in the study, questions arose concerning the best way to test radar systems. Many factors affect the performance of radar, including the size, shape, and composition of the object that is to be detected; the height of the radar antenna(s); and the relative motion of the radar system and/or object. This report discusses several different test procedures and test targets and recommends methods to determine how effective a radar system will be in detecting a person near heavy equipment.

Jan 1, 2002

By Wilson G. L, Lord J. H

A detailed analysis of faulting indicatcs that blocks of "greenstone" have been thrust beneath the southern end of the Mt. Isa orebodies.This "greenstone" basement is considered to be a major structural control in the localization of these orebodies.INTRODUCTIONThis paper is based on exploration carried out by Mining Corporation (Aust.) N.L. from 1956 to 1960 in the area immediately south of Mt. Isa, Queensland. During this period over 20,000 ft of diamond drilling was completed together with costeaning and geochemical exploration.Early in 1959, it became apparent that diamond drill information could not be correlated with the current geological concepts of this area and a detailed geological appraisal became necessary. In all, sixty square miles were mapped at a scale of 1 in. to 500 ft, using enlarged aerial photographs. All drill core was logged and sections re-interpreted.Professor K. C. Dunham of the University of Durham consulted on this project and contributed through valuable discussion. Dr. A. Day of the University of Sydney carried out a gravity survey in February 1960 and Dr. H. Wilshire of the same University undertook microscopic examination of rocks from the area. Certain sections of the area were investigated geochemically by Mr. K. K. Hughes of New Consolidated Gold Fields (Asia) Pty. Limited in 1960.In outlining a theory of ore genesis in the area the writers have drawn heavily on the invaluable data published by many previous workers on the Mt. Isa field, in particular...

Jan 1, 1963

By Luciano Almeida de Freitas

Este artigo tem como objetivo verificar os resultados da aplicação de ações que almejam a excelência no processo de carga, descarga e transporte de minério ferro de uma empresa situada na Região do Médio Piracicaba em Minas Gerais. Esta pesquisa é um estudo de caso de natureza exploratória e documental. No desenvolvimento deste estudo foram analisados os documentos da empresa, que referem-se às atas de reunião e relatórios gerenciais. As reuniões foram realizadas pelos gestores e supervisores do processo de carga, descarga e transporte de minério para identificar falhas e apresentar ações que almejassem a excelência no processo produtivo. Por fim, os resultados foram verificados e identificou um aumento no índice da utilização física dos caminhões de 11,46%, aumento da produtividade horária de 27,5% e um crescimento da movimentação total de produção dos caminhões de 23,92%. Com isso, pode-se verificar os ganhos com a aplicação das ações implementadas, que almejam a excelência nas operações.

Oct 30, 2017

By Eileen Ashworth

Computer-assisted instruct ion is now being used in areas as diversified as training handicapped children to preflight simulation for airline pilots. This paper reports on two courses that have been developed at SDSM&T on the PLATO system for miner safety training. Advantages of computer-assisted instruct ion for this type of training is discussed. (Figures show examples of actual use.) A discussion will be given on other applications such as maintenance troubleshooting, training of engineers and managers at remote sites and training of local people for working in the mine.

Jan 1, 1983

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990