Search Documents

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

Evaluation of the Iron Blast Furnace Process using Heat and Material Balances of the Flame-Zone

Sep 13, 2010

By P. A. Rey

Water recycle is an important part of the coal preparation process. This study was directed toward: (1) a survey of current practice and an evaluation of both the solid and liquid components of blackwater, (2) an experimental study of blackwater flocculation, and (3) a fundamental analysis of the flocculation process. The solids contained in the blackwater discharge to the fine refuse thickener of a coal preparation plant were found to contain, on average, 56% coal and 44% mineral matter. The mineral matter was largely illitic clay, while the water phase contained relatively large amounts of S04 and Ca++. Detailed studies were made of both natural and synthetic flocculants and the influence of polymer type and pH on the settling rate, turbidity of the supernatent liquid and sludge volume of the settled solids. More tundamental studies were made that clearly indicate the need for controlled mixing of polymer into the suspension to be flocculated, and the need to evaluate, more closely, the structure of the flocs formed during the process. Research recommendations are given.

Jan 1, 1983

By E. R. Maize

[In %-port of Invcstiptionn 7452 ,g dcniing with roof ~wet,ent in the Cmcibla r~ine, rof&apos;erence .,as m.da to the f~ct tiwt timker decny war, bsing studied at tho tine of writing. Thic napor, written a3er completion of that ~tudy, describ~s t1l.e ~mrl&apos;: and sunlharizea the fiats obtained. Ifhen tlle stu* oi roof novement bras be,- at Cxcible tw igeas \%.ere a6-r;incsd. on decay of tiriber Q: scne of :he olficialr;: (I.) 9:la.t timber decay v:as unustmlly rapid in ,tho Ciuoiblc mins, ,m?. ((2) that timber coated with rock ri..~st deixiyad morrl mpirlly thnn those %hat vsrc not so coated. Thsx ::ore no records by which tkeso &apos;iaeas could &apos;L;e tertcc?, ard it cnpsarefi vise to make a limite6 in- vo3tiption, p~.rticu!.ai.ly of +.he effect of roc!< dusting on decny, as rock ductirg is nn importnnt mer-ns of ~rc-,rcnt?;~g cad-dust eql-osions. ]

Jan 1, 1941

By Karl E. Burgher

Since World War II, the need for the use of explosives with testing, construction, demolition, mining and quarrying near urban areas has increased dramatically. Once remote, testing areas have been encroached upon by commercial and residential areas. Evidence has been found that overpressure levels near these areas can be estimated using meteorological conditions. This paper reviews a study where 205 test shots were fired, meteorological conditions recorded, and over-pressure levels estimated using multiple regression techniques.

Jan 1, 1988

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

Study on Mineral Processing of Refractory Copper-Nickel Ore

Sep 13, 2010

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By B Mohanty, G Yamin

A number of parameters, aside from blast design and pre-existing rock conditions, can change the performance of the explosives system in actual blasting practice. Sympathetic pressures caused by detonation of preceding holes have been identified as a major contributor to explosive system malfunctions, leading to uneven blasting performance. These effects can occur both within a hole or across several holes. These can consist of high transient pressures related to the shock phase of the explosion or the relatively longer or quasi-static pressures associated with the explosion gas expansion phase. This study presents the findings from an on- going investigation on measurement and analysis of these pressures between donor and receptor holes in a granitic outcrop for representative inter-hole distances and borehole conditions, employing single cartridges of emulsion explosive in 45 mm diameter holes. The results, despite wide scatter in the measured values, show the very short duration pressures to range up to 7 MPa and arriving within a few milliseconds after detonation, whereas the much lower amplitude pressures arrive after tens of milliseconds. Both have the potential to seriously affect the performance of an explosives system.

Jan 1, 2005

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By Wolfgang Gütter

India is targeting to boost its electrical capacity from 100 GW to 200 GW within the next 10 years. The National Hydroelectric Power Corporation (NHPC) has decided in2001 to take execution of the 800 MW Stage-II of the prestigious 2,051 MW Parbatihydrol electric project in Kulu district of the northern province Himachal Pradesh. Two parallel 30° inclined underground pressure shafts of 1.542m in length each will be excavated in different geological formations and lined with hexagonal concrete segments by a hard rock double shield TBM. That kind of heading will be a novelty to India and an innovative method for inclined pressure shafts. The 4.88m Mitsubishi DSTBM will be assembled underground on a swivelling steel platform especially designed for the launching as well as for the acceptance of the TBM in the upper cavern of each shaft. The hexagonal segmental lining system causes a significant higher job safety than an open TBM with conventional support. Each ring consists of four honeycomb segments with 20 cm thickness. After finalisation of the excavation a steel liner will be installed and concreted. The Joint Venture Jäger-Seli will perform the two pressure shafts as a sub-contractor for the Indian company Gammon India Ltd.

Jan 1, 2005

By Aline da Luz Pascoal

A crescente preocupação com a produção e descarte de rejeitos advindos da exploração mineral, principalmente no que diz respeito aos fatores econômicos e ao meio ambiente, tem aguçado a procura por novos métodos de processamento que ajudem a minimizar este fato. De maneira que, serão avaliados e discutidos os dados de produção de um concentrado (sinter feed fino) em um circuito de concentração magnética na empresa Pedreira Um Valemix em Catas Altas/MG, tendo como alimentação da planta de beneficiamento um blend composto pelo rejeito outrora gerado nesta mesma planta (teor 40,0%) Fe e o ROM (teor de 42,0% Fe). Os resultados encontrados mostraram-se promissores, alcançando uma recuperação mássica e recuperação metalúrgica de, respectivamente 60,15% e 79,75%, e também geraram maior estabilidade do processo, prolongamento da vida útil da mina e maior receita devido à utilização de um produto que outrora era considerado como rejeito.

Oct 30, 2017

By M. F. Koehler

[THE LITERATURE contains relatively few thermodynamic values for interoxidic compounds, and these often are unreliable. This is especially true of data for ferrites and aluminates for which heat of formation determinations may involve extreme experimental difficulties. This report contains the results of new experimental work for obtaining the heats of formation of five ferrites (Ca2Fe2O5, CaFe2O4, MgFe2O4,, NaFeO2, and LiFeO2) and one aluminate (CaAl4O7), and a review and revision of previous similar work of this laboratory on five aluminates (Ca3A12O6,, 12/7 CaO-Al2O3, CaAl2O4, NaA1O2, and LiAlO2), The results for the 11 compounds are combined with entropy and high-temperature heat content data to derive tables of heats and free energies of formation (both from the oxides and from the elements) for the temperature range 298° 1,800° K, The relative stabilities of the compounds are discussed. The presented data all have application to ceramic reactions, and those for the calcium and sodium aluminates are applicable in considering soda-lime sintering processes for extracting alumina from silicate minerals such as day and labradorite.]

Jan 1, 1961

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l&apos;étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L&apos;étude de champs a démontré l&apos;interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l&apos;influence d&apos;augmenter de dimension de l&apos;excavation. La raideur de piliers overburden, la proportion d&apos;extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d&apos;influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d&apos;un pilier a reçu l&apos;influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L&apos;impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d&apos;interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By A. Dean, J. Roberts, I. Stone, J. R. Merefield

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 11 refs. No completely reliable method for characterising and quantifying airborne dust risk exists. A new monitoring technology has been developed whereby dust collected from four-way directional and high volume samplers is analysed for mineral content and particle size for integrated dust mapping. A dust database was set up for the area surrounding the Ffos Las open cast coal site in South Wales. It included XRD directional traces from 17 gauges over 20 months, XRD traces from window ledges in the nearby communities, the major soil types in the area, dust data from haulage roads and public roads and reference-type mineral samples. The database can be accessed relationally to compare and analyse the data using mineral, direction, time, weather and geographical relationships. The data has been used to assess areas of low, intermediate and high levels of risk from dust fall-out

Apr 1, 1995

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments with surface support liners which includes shotcrete and thin spray-on liners (also referred to as sealants, coatings and membranes) from a ground control perspective. The proper selection and use of a surface support material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is to evaluate the preliminary findings of a long-term underground study of various types of surface support liners, and to examine installation practices that are critical for an effective liner material application. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and thin spray-on liner materials. Liner material performance to date was evaluated on a regular basis over a three year period. Although the study is still ongoing, critical mining practices were identified that may seriously affect the bond of the liner material to the mine roof and rib.

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994